Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0076198 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions (A) through (C) is met (2-trip detection logic)
(A) Either of the following conditions 1, 2 or 3 is met:
1. Any 2 or more signals of the following are ON simultaneously:
·

P input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


2. Any 2 or more signals of the following are ON simultaneously:
·

N input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


3. Any 2 or more signals of the following are ON simultaneously:
·

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


(B) All switches are OFF simultaneously for P, N, NSW, R and D.
(C) When any of following conditions is met for 2.0 sec. or more in the S position:
·

P input signal is ON.

·

N input signal is ON.

·

NSW input signal is ON.

·

R input signal is ON.


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

Lower shift lever assembly (Transmission control switch)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, NSW, R or D). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C245326E02
6.094,5 6.448,5.167 0.354,0.167 10 ECM 5.708,0.823 6.042,0.99 0.333,0.167 10 67 5.708,1.333 6.063,1.5 0.354,0.167 10 71 5.719,1.833 6.083,2 0.365,0.167 10 66 5.75,2.292 6.073,2.458 0.323,0.167 10 70 5.656,3.042 6,3.208 0.344,0.167 10 E26 5.729,2.844 6.073,3.01 0.344,0.167 10 63 5.667,4.563 6.021,4.729 0.354,0.167 10 A25 6,1 6.24,1.167 0.24,0.167 10 D 6,1.521 6.24,1.688 0.24,0.167 10 N 6,2.021 6.24,2.188 0.24,0.167 10 R 6,2.521 6.24,2.688 0.24,0.167 10 P 6,3.042 6.604,3.208 0.604,0.167 10 NSW 5.969,4.563 6.208,4.729 0.24,0.167 10 S 5.708,4.385 5.948,4.552 0.24,0.167 10 27 3.052,1.104 3.292,1.271 0.24,0.167 10 7 3.052,1.615 3.292,1.781 0.24,0.167 10 8 3.052,2.135 3.292,2.302 0.24,0.167 10 2 3.052,2.646 3.292,2.813 0.24,0.167 10 3 3.052,3.156 3.292,3.323 0.24,0.167 10 4 1.875,3.156 2.115,3.323 0.24,0.167 10 9 1.875,1.938 2.115,2.104 0.24,0.167 10 1 1.875,4.667 2.115,4.833 0.24,0.167 10 4 2.781,1.104 3.021,1.271 0.24,0.167 10 DL 2.781,1.615 3.021,1.781 0.24,0.167 10 NL 2.781,2.135 3.021,2.302 0.24,0.167 10 RL 2.063,1.938 2.302,2.104 0.24,0.167 10 RB 2.781,2.646 3.021,2.813 0.24,0.167 10 PL 2.833,3.156 3,3.323 0.167,0.167 10 B 2.844,4.677 3.083,4.844 0.24,0.167 10 S 2.063,4.667 2.302,4.833 0.24,0.167 10 IG 0.167,1.51 0.698,2.302 0.531,0.792 10 from BKUP LP Fuse 0.052,4.208 0.74,5.01 0.688,0.802 10 from ECU-IG1 NO. 1 Fuse 0.323,3.042 0.75,3.583 0.427,0.542 10 to ST Relay 1.635,3.5 2.01,3.688 0.375,0.188 10 E4 1.604,5 4.073,5.188 2.469,0.188 10 Transmission Control Switch 2.073,3.156 2.24,3.323 0.167,0.167 10 L 3.052,4.667 3.271,4.833 0.219,0.167 10 5 1.635,3.667 3.406,4.063 1.771,0.396 10 Park/Neutral Position Switch Assembly 1.604,4.865 1.969,5.042 0.365,0.177 10 I44 5.667,2.531 6.01,2.698 0.344,0.167 10 E26 5.667,2.021 6.01,2.188 0.344,0.167 10 E26 5.656,1.51 6,1.677 0.344,0.167 10 E26 5.656,1 6,1.167 0.344,0.167 10 E26

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever is in P or N

·

OFF: Shift lever is not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever is in P

·

OFF: Shift lever is not in P


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever is in R

·

OFF: Shift lever is not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever is in N

·

OFF: Shift lever is not in N


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever is in D or S

·

OFF: Shift lever is not in D or S


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever is in S, "+" or "-"

·

OFF: Shift lever is not in S, "+" or "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 147,125,126,127,133,128


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C190067C01
0.469,1.573 0.813,1.833 0.344,0.26 1.656,1.594 2.094,1.063 false 2.125,0.906 2.427,1.094 0.302,0.188 10 RB 0.573,1.625 0.875,1.771 0.302,0.146 10 E4 0.823,0.677 1.031,0.865 0.208,0.188 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E4-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.
C190067C02
0.49,1.573 0.823,1.833 0.333,0.26 2.198,1.646 2.865,1.271 false 2.906,1.135 3.302,1.281 0.396,0.146 10 B 0.573,1.625 0.917,1.771 0.344,0.146 10 E4 0.698,0.75 0.885,0.958 0.188,0.208 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E4-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C275091C01
0.219,2.271 0.51,2.521 0.292,0.25 1.167,1.708 0.74,1.177 false 1.344,1.708 1.125,1.188 false 1.604,1.688 1.75,1.167 false 1.896,1.698 2.177,1.177 false 1.75,2.135 2.052,2.625 false 1.417,2.135 1.5,2.646 false 1.24,2.146 1.052,2.604 false 0.354,0.771 0.667,0.969 0.313,0.198 10 *a 0.281,2.313 0.594,2.51 0.313,0.198 10 E4 1.01,2.667 1.167,2.865 0.156,0.198 10 L 1.438,2.667 1.75,2.865 0.313,0.198 10 NL 2,2.667 2.313,2.865 0.313,0.198 10 DL 0.667,0.969 0.823,1.167 0.156,0.198 10 B 1.021,0.969 1.333,1.167 0.313,0.198 10 PL 1.667,0.969 1.979,1.167 0.313,0.198 10 RL 2.104,0.969 2.417,1.167 0.313,0.198 10 RB
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
E4-4 (B) - E4-9 (L) P or N Below 1 Ω
Except P and N 10 kΩ or higher
E4-1 (RB) - E4-3 (PL) P Below 1 Ω
Except P 10 kΩ or higher
E4-1 (RB) - E4-8 (NL) N Below 1 Ω
Except N 10 kΩ or higher
E4-1 (RB) - E4-2 (RL) R Below 1 Ω
Except R 10 kΩ or higher
E4-1 (RB) - E4-7 (DL) D, S, "+" or "-" Below 1 Ω
Except D, S, "+" and "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C08
0.302,1.021 0.729,1.313 0.427,0.292 1.417,1.323 1.198,1.833 false 1.125,1.323 0.906,1.667 false 0.188,0.167 0.406,0.375 0.219,0.208 10 *a 0.802,1.677 0.958,1.854 0.156,0.177 10 S 1.073,1.854 1.26,2.063 0.188,0.208 10 IG 0.417,1.083 0.698,1.26 0.281,0.177 10 I44
*a Component without harness connected
(Transmission Control Switch)


Connect the park/neutral position switch assembly connector.


b.

Disconnect the transmission control switch connector from lower shift lever assembly.


c.

Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Position Specified Condition
I44-4 (IG) - I44-5 (S) S, "+" and "-" Below 1 Ω
Except S, "+" and "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.
C245085C01
0.531,0.948 0.99,1.167 0.458,0.219 1.917,2.531 2.229,1.875 false 0.646,0.979 1.031,1.156 0.385,0.177 10 A25 0.406,0.427 0.688,0.625 0.281,0.198 10 *a 1.833,2.542 2.156,2.75 0.323,0.208 10 S
*a Front view of wire harness connector
(to ECM)


Connect the transmission control switch connector.


b.

Disconnect the ECM connectors.


c.

Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Shift Lever Position Specified Condition
A25-27 (S) - Body ground S, "+" or "-" 11 to 14 V
Except S, "+" and "-" Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
C245086C01
0.365,0.802 0.76,1.031 0.396,0.229 0.698,1.802 0.49,2.49 false 0.771,1.802 0.979,2.333 false 1.073,1.813 1.396,2.563 false 1.146,1.813 1.677,2.344 false 0.156,0.375 0.448,0.573 0.292,0.198 10 *a 1.385,2.594 1.781,2.802 0.396,0.208 10 P 1.698,2.333 2,2.542 0.302,0.208 10 N 0.927,2.365 1.229,2.573 0.302,0.208 10 D 0.427,2.51 0.729,2.719 0.302,0.208 10 R 0.427,0.833 0.823,1.01 0.396,0.177 10 E26
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Shift Lever Position Specified Condition
E26-70 (P) - Body ground P 11 to 14 V
Except P Below 1 V
E26-71 (N) - Body ground N 11 to 14 V
Except N Below 1 V
E26-66 (R) - Body ground R 11 to 14 V*
Except R Below 1 V
E26-67 (D) - Body ground D, S, "+" or "-" 11 to 14 V
Except D, S, "+" and "-" Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E4-4 (B) - E26-63 (NSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E4-4 (B) or E26-63 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR