Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU.

·

The ABS control system is defective.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM

C243440E01
6.115,1.042 6.656,1.458 0.542,0.417 10 CANL 6.115,1.906 6.615,2.24 0.5,0.333 10 CANH 6.115,3.771 6.49,4.167 0.375,0.396 10 IG1 6.115,4.729 6.521,4.896 0.406,0.167 10 GND1 5.854,0.938 6.188,1.313 0.333,0.375 10 14 5.854,1.802 6.229,2.156 0.375,0.354 10 26 5.854,3.677 6.177,4.063 0.323,0.385 10 28 5.854,4.604 6.156,4.896 0.302,0.292 10 38 0.813,1.083 1.427,1.333 0.615,0.25 10 CANL 0.813,1.948 1.375,2.219 0.563,0.271 10 CANH 1.333,0.938 1.771,1.427 0.438,0.49 10 15 1.333,1.802 1.688,2.229 0.354,0.427 10 16 5.5,5.792 5.875,5.99 0.375,0.198 10 A49 5.5,5.958 7.031,6.469 1.531,0.51 10 Skid Control ECU (Brake Actuator Assembly) 0.229,5.792 0.552,5.958 0.323,0.167 10 I18 0.229,5.948 1.396,6.417 1.167,0.469 10 Combination Meter Assembly 4.24,3.948 5.344,4.302 1.104,0.354 10 ECU-IG1 NO. 1 1.969,3.792 3.458,4.135 1.49,0.344 10 from IG1 NO. 2 Relay 6.115,2.833 6.563,3.375 0.448,0.542 10 +BS 5.854,2.74 6.188,3.052 0.333,0.313 10 25 4.333,3 5.302,3.333 0.969,0.333 10 ABS NO. 2 2.51,2.833 3.552,3.115 1.042,0.281 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C238832C30
0.177,0.698 0.656,1.021 0.479,0.323 1.24,1.51 0.958,0.76 false 0.375,2.729 0.729,1.604 false 2.813,1.469 3.021,0.76 false 0.24,0.177 0.729,0.667 0.49,0.49 10 *a 0.313,0.781 0.865,1.156 0.552,0.375 10 A49 0.208,2.75 0.708,3.031 0.5,0.281 10 +BS 0.823,0.583 1.24,0.948 0.417,0.365 10 IG1 2.771,0.583 3.344,0.917 0.573,0.333 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A49 skid control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V
A49-25 (+BS) - A49-38 (GND1) Always 11 to 14 V
A49-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A49-28 (IG1) - A49-38 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C31
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.542,0.604 0.271,0.406 10 *a 0.333,0.802 0.865,1.167 0.531,0.365 10 A49 1.948,0.563 2.615,1.042 0.667,0.479 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the A49 skid control ECU connector.


b.

Perform an Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp ABS
50004 122 13

c.

Check the combination meter assembly.

OK:

The ABS warning light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY