Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C238832C19
0.177,0.698 0.656,1.021 0.479,0.323 1.24,1.521 0.958,0.76 false 0.375,2.729 0.75,1.604 false 2.813,1.5 3.021,0.76 false 0.24,0.177 0.458,0.448 0.219,0.271 10 *a 0.313,0.781 0.885,1.313 0.573,0.531 10 A49 0.208,2.75 0.5,2.906 0.292,0.156 10 +BS 0.823,0.583 1.104,0.74 0.281,0.156 10 IG1 2.771,0.583 3.177,0.74 0.406,0.156 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V
A49-25 (+BS) - A49-38 (GND1) Always 11 to 14 V
A49-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A49-28 (IG1) - A49-38 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1417 is not output. A
DTC C1417 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B