Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning and slip indicator lights.

WIRING DIAGRAM

C243628E06
5.97,0.689 6.369,0.842 0.399,0.153 10 CANL 5.505,1.807 5.785,1.959 0.28,0.153 10 A49 5.702,0.584 5.893,0.737 0.191,0.153 10 14 5.702,1.285 5.893,1.438 0.191,0.153 10 26 1.402,0.584 1.593,0.737 0.191,0.153 10 26 1.402,1.285 1.593,1.438 0.191,0.153 10 13 1.402,2.866 1.649,3.018 0.247,0.153 10 23 5.97,1.39 6.39,1.543 0.42,0.153 10 CANH 0.905,0.703 1.304,0.856 0.399,0.153 10 CANL 0.884,1.404 1.304,1.557 0.42,0.153 10 CANH 5.97,2.959 6.178,3.112 0.208,0.153 10 TC 1.097,2.973 1.306,3.126 0.208,0.153 10 TC 5.721,2.866 5.903,3.018 0.182,0.153 10 13 5.804,3.491 5.903,3.644 0.1,0.153 10 4 5.97,3.589 6.213,3.742 0.243,0.153 10 CG 6.17,4.12 6.469,4.273 0.299,0.153 10 I39 6.17,4.26 6.555,4.413 0.385,0.153 10 DLC3 5.505,1.947 7.133,2.296 1.628,0.35 10 Skid Control ECU (Brake Actuator Assembly) 0.732,4.26 1.108,4.413 0.376,0.153 10 ECM 0.732,4.12 1.015,4.273 0.283,0.153 10 A25

CAUTION / NOTICE / HINT

HINT:

When the indicator lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C207407C20
0.219,0.979 0.667,1.271 0.448,0.292 1.604,1.917 1.104,0.958 false 1.854,2.385 2.531,0.958 false 0.333,0.302 0.521,0.469 0.188,0.167 10 *a 0.958,0.76 1.198,0.927 0.24,0.167 10 CG 0.365,1.042 0.698,1.188 0.333,0.146 10 I39 2.438,0.76 2.677,0.927 0.24,0.167 10 TC
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I39-13 (TC) - I39-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C207407C20
0.219,0.979 0.667,1.271 0.448,0.292 1.604,1.917 1.104,0.958 false 1.854,2.385 2.531,0.958 false 0.333,0.302 0.521,0.469 0.188,0.167 10 *a 0.958,0.76 1.198,0.927 0.24,0.167 10 CG 0.365,1.042 0.698,1.188 0.333,0.146 10 I39 2.438,0.76 2.677,0.927 0.24,0.167 10 TC
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A25 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - A25-23 (TC) Always Below 1 Ω
I39-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C21
0.219,0.979 0.667,1.271 0.448,0.292 1.635,1.958 2.427,1.01 false 0.333,0.302 0.521,0.469 0.188,0.167 10 *a 2.313,0.813 2.552,0.979 0.24,0.167 10 CG 0.365,1.042 0.698,1.188 0.333,0.146 10 I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C207407C22
0.25,0.979 0.698,1.271 0.448,0.292 1.604,1.938 1.104,0.958 false 1.823,2.385 2.531,0.958 false 0.333,0.302 0.521,0.469 0.188,0.167 10 *a 0.958,0.76 1.198,0.927 0.24,0.167 10 CG 0.365,1.042 0.698,1.188 0.333,0.146 10 I39 2.438,0.76 2.677,0.927 0.24,0.167 10 TC
*a Front view of DLC3


Replace the ECM.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG