Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0073970 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E232249E10
6.162,3.289 6.499,3.436 0.337,0.147 10 ECM 5.812,3.289 6.148,3.436 0.337,0.147 10 A25 5.561,1.024 5.745,1.184 0.184,0.161 10 23 5.832,1.117 6.049,1.274 0.216,0.156 10 TC 1.053,3.261 1.439,3.408 0.385,0.147 10 DLC3 0.759,3.261 1.043,3.408 0.284,0.147 10 I39 1.272,1.127 1.491,1.274 0.219,0.147 10 TC 1.26,2.252 1.491,2.399 0.23,0.147 10 CG 1.555,1.024 1.739,1.168 0.184,0.145 10 13 1.597,2.146 1.695,2.291 0.098,0.145 10 4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A25-23 (TC) - I39-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - ECM)

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
E265513C07
1.49,0.396 1.781,0.594 0.292,0.198 0.917,0.479 1.583,1.063 false 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.542,0.417 2,0.615 0.458,0.198 10 false I39 0.688,0.396 1,0.594 0.313,0.198 10 false CG
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
E265513C08
1.49,0.396 1.771,0.594 0.281,0.198 2.406,1.958 1.771,1.625 false 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.542,0.417 2,0.615 0.458,0.198 10 false I39 2.458,1.885 2.771,2.083 0.313,0.198 10 false TC
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR