Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2011.10–2015.04
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) W

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  CUSTOMIZE PARAMETERS  


HINT:

The following items can be customized.


NOTICE:
·

When the customer requests a change in a function, first make sure that the function can be customized.

·

Record the current settings before customizing.



Customizing with the intelligent tester


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body or Entry&Start / Utility / Customize / Wireless Door Lock, Entry&Start or Warning.


e.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back When the doors are locked by entry function, the hazard warning lights flash once.
When the doors are unlocked by entry function, the hazard warning lights flash twice.
ON 0:OFF,1:ON Main body ECU (multiplex network body ECU)
Open Door Warning The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open. ON 0:OFF,1:ON Main body ECU (multiplex network body ECU)
Auto Lock Time Function that regulates the interval between unlocking and automatic relocking of doors. 30 s 00:30 s,01:60 s,10:120 s Main body ECU (multiplex network body ECU)
Wireless Buzzer Resp Function that sounds the answer-back buzzer when an entry lock or unlock operation is performed*. ON 0:OFF,1:ON Main body ECU (multiplex network body ECU)
Wireless Buzzer Vol Buzzer answer back volume* Level 5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (multiplex network body ECU)
50006 1

*: w/ Wireless Door Lock Buzzer Answer Back Function


Entry & Start
Tester Display Description Default Setting ECU
Park Wait Time Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. 2.5s 00:0.5s,01:1.5s,10:2.5s,11:5s Certification ECU (smart key ECU assembly)
Ignition Available Area Function that sets the area that the key must be in before the engine switch can be operated. All 00:Front,01:All Certification ECU (smart key ECU assembly)
Trunk Open Mode Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the luggage door opening switch assembly. ON 0:OFF,1:ON Certification ECU (smart key ECU assembly)
Door Unlock Mode2 Function that chooses the doors to be operated by entry unlock operation. All 0:All,1:Driver Certification ECU (smart key ECU assembly)
Auto Entry Cancel SW Function that enables or disables the smart entry and start system. OFF 0:OFF,1:ON Certification ECU (smart key ECU assembly)
Touch Activation Over Threshold The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active 0:Active,1:Not Active Certification ECU (smart key ECU assembly)
Engine Start Indicator Function that turns the smart warning light on the combination meter assembly on or off. ON 0:OFF,1:ON Certification ECU (smart key ECU assembly)
50006 17
Warning
Tester Display Description Default Setting ECU
Key Low Battery Warning Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. ON 0:OFF,1:ON Certification ECU (smart key ECU assembly)
50006 7


Customizing with the multi-display (Navigation receiver assembly (w/ Navigation System))


a.

Turn the engine switch on (IG).


b.

Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.


c.

Select the setting by referring to the table below.

Display Default Content Setting Relevant ECU
Select doors to unlock All Doors Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly)
Entry and start system On Function that enables or disables the smart key system. On or Off Certification ECU (smart key ECU assembly)



Customizing with the multi-display (Radio and Display Receiver Assembly (w/ Audio and Visual System (for Radio and Display Type))


a.

Turn the engine switch on (IG).


b.

Enter the following menus: SETUP / Vehicle.


c.

Select the setting by referring to the table below.

Display Default Content Setting Relevant ECU
Entry and start system On Function that enables or disables the smart entry and start system. On or Off Certification ECU (smart key ECU assembly)



Customizing with the multi-display (Radio and Display Receiver Assembly (w/ Audio and Visual System (for Radio and Display Type))


a.

Turn the engine switch on (IG).


b.

Enter the following menus: SETUP / Vehicle.


c.

Select the setting by referring to the table below.

Display Default Content Setting Relevant ECU
Entry and start system On Function that enables or disables the smart entry and start system. On or Off Certification ECU (smart key ECU assembly)



Entry unlock mode switching function (manual operation)


a.

The following entry unlock modes can be selected when using the entry unlock mode switching function.

·

All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

·

Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.



b.

When customizing through manual operation:

1.

Turn the engine switch off.

2.

Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.

3.

Check the current setting.

HINT:
·

The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

·

The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.



Currently Selected Mode Answer-back (Wireless Buzzer) Answer-back (Buzzer in Combination Meter Assembly)
All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once

4.

Release the lock and unlock buttons of the electrical key transmitter sub-assembly.

5.

Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

HINT:

Repeat the procedure as necessary to select the desired mode.


6.

Unlock the doors with the wireless operation, and then open any door


B281958
3.646,6.146 3.646,6.469 3.646,6.469 3.365,6.469 false 1.594,0.698 3.323,0.844 1.729,0.146 10 false Wireless Door Lock Buzzer 4.375,0.948 5.938,1.094 1.563,0.146 10 false Multi-information Display 4.604,0.479 6.458,0.625 1.854,0.146 10 false Combination Meter Assembly 6.448,0.948 6.917,1.115 0.469,0.167 10 false Buzzer 0.281,2.188 1.021,2.354 0.74,0.167 10 false Driver Door 0.354,3.906 0.948,4.063 0.594,0.156 10 false All Doors 1.99,2.552 3,2.719 1.01,0.167 10 false Sounds 3 times 1.948,4.198 2.958,4.365 1.01,0.167 10 false Sounds 2 times 1.594,3.74 1.844,3.885 0.25,0.146 10 false ON 1.531,4.021 1.865,4.167 0.333,0.146 10 false OFF 1.365,2.375 1.698,2.521 0.333,0.146 10 false OFF 1.438,2.094 1.688,2.24 0.25,0.146 10 false ON 6.448,2.677 6.938,3.115 0.49,0.438 10 false Sounds once 4.865,1.365 6.104,1.708 1.24,0.344 10 false Driver door "OPEN" indication (for LHD) 4.865,2.396 6.104,2.74 1.24,0.344 10 false Driver door "OPEN" indication (for RHD) 4.865,3.51 6.125,4.031 1.26,0.521 10 false All doors "OPEN" indication 1.771,6.365 3.323,6.563 1.552,0.198 10 false Multi-information Display



Entry cancel function (manual operation)


HINT:

While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


a.

The following functions are disabled when the smart entry and start system is canceled.

1.

Entry unlock/lock functions

2.

Entry luggage compartment door open function

3.

Push start function

4.

Key lock-in prevention function

5.

Entry warning functions



b.

When canceling the system through manual operation:

1.

Make sure the following conditions are met:

·

The engine switch is off.

·

The driver door is closed.

·

The driver door is unlocked.


2.

Press the unlock button of the electrical key transmitter sub-assembly.

3.

Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

4.

With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

NOTICE:

If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.


5.

Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).

6.

With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

NOTICE:

If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.


7.

Close and open the driver door completing the step above (driver door: open condition → closed → opened).

8.

Close the driver door within 5 seconds of completing the above step.

9.

Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.


HINT:

Finish the step 5 to 7 within 30 seconds.



c.

Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

1.

Perform the procedures to cancel the smart entry and start system again.

2.

Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

HINT:
·

The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

·

The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.