USING INTELLIGENT TESTER
Connect the intelligent tester to the DLC3.
Monitor the ECU data by following the prompts on the intelligent tester screen.
The intelligent tester has a "Snapshot" function which records the monitored data. Refer to the intelligent tester operator's manual for further details.
DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Mirror L or Mirror R / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 signal | ON or OFF | ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off |
- |
| Seat Memory Switch2 | Seat memory switch M2 signal | ON or OFF | ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off |
- |
| Seat Memory Switch3 | Seat memory switch M3 signal* | ON or OFF | ON: Seat memory switch M3 on
OFF: Seat memory switch M3 off |
Not applicable |
| Seat Memory Set SW | Seat memory switch SET signal | ON or OFF | ON: Seat memory switch SET on
OFF: Seat memory switch SET off |
- |
| Mirror Memory No.1 | Mirror position memorized in memory switch M1 | ON or OFF | ON: Memorized
OFF: Not memorized |
- |
| Mirror Memory No.2 | Mirror position memorized in memory switch M2 | ON or OFF | ON: Memorized
OFF: Not memorized |
- |
| Mirror Memory No.3 | Mirror position memorized in memory switch M3* | ON or OFF | ON: Memorized
OFF: Not memorized |
Not applicable |
| Mirror Vertical Sensor Vol | Vertical mirror position | MIN: 0, MAX: 4.98 V | Within range from 0 to 4.98 V | - |
| Mirror Horizontal Sensor Vol | Horizontal mirror position | MIN: 0, MAX: 4.98 V | Within range from 0 to 4.98 V | - |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 signal | ON or OFF | ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off |
- |
| Seat Memory Switch2 | Seat memory switch M2 signal | ON or OFF | ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off |
- |
| Seat Memory Switch3 | Seat memory switch M3 signal* | ON or OFF | ON: Seat memory switch M3 on
OFF: Seat memory switch M3 off |
Not applicable |
| Seat Memory Set SW | Seat memory switch SET signal | ON or OFF | ON: Seat memory switch SET on
OFF: Seat memory switch SET off |
- |
| Mirror Memory No.1 | Mirror position memorized in memory switch M1 | ON or OFF | ON: Memorized
OFF: Not memorized |
- |
| Mirror Memory No.2 | Mirror position memorized in memory switch M2 | ON or OFF | ON: Memorized
OFF: Not memorized |
- |
| Mirror Memory No.3 | Mirror position memorized in memory switch M3* | ON or OFF | ON: Memorized
OFF: Not memorized |
Not applicable |
| Mirror Vertical Sensor Vol | Vertical mirror position | MIN: 0, MAX: 4.98 V | Within range from 0 to 4.98 V | - |
| Mirror Horizontal Sensor Vol | Horizontal mirror position | MIN: 0, MAX: 4.98 V | Within range from 0 to 4.98 V | - |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock SW-Lock | Door control switch (power window regulator master switch assembly) lock signal | ON or OFF | ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| Door Lock SW-Unlock | Door control switch (power window regulator master switch assembly) unlock signal | ON or OFF | ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| FR Door Courtesy | Driver door courtesy switch condition | ON or OFF | ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed) |
- |
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | ON or OFF | ON: Mirror select switch in R position
OFF: Mirror select switch off or in L position |
- |
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | ON or OFF | ON: Mirror select switch in L position
OFF: Mirror select switch off or in R position |
- |
| Mirror Position SW (R) | Mirror adjust switch signal (Right) | ON or OFF | ON: Mirror adjust switch pressed right
OFF: Mirror adjust switch not pressed right |
Check with the mirror select switch in any position except neutral |
| Mirror Position SW (L) | Mirror adjust switch signal (Left) | ON or OFF | ON: Mirror adjust switch pressed left
OFF: Mirror adjust switch not pressed left |
Check with the mirror select switch in any position except neutral |
| Mirror Position SW (Up) | Mirror adjust switch signal (Up) | ON or OFF | ON: Mirror adjust switch pressed up
OFF: Mirror adjust switch not pressed up |
Check with the mirror select switch in any position except neutral |
| Mirror Position SW (Dwn) | Mirror adjust switch signal (Down) | ON or OFF | ON: Mirror adjust switch pressed down
OFF: Mirror adjust switch not pressed down |
Check with the mirror select switch in any position except neutral |
| Mem SW No. w/KeyID1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7* |
- |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Mirror L or Mirror R / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Up/Down | Mirror vertical operation | Up / Down | ·
Operate with engine switch on (IG) and the vehicle stopped. ·
This test activates the mirror up or down. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Right/Left | Mirror horizontal operation | Right / Left | ·
Operate with engine switch on (IG) and the vehicle stopped. ·
This test tilts the mirror right or left. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Up/Down | Mirror vertical operation | Up / Down | ·
Operate with engine switch on (IG) and the vehicle stopped. ·
This test activates the mirror up or down. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Mirror Right/Left | Mirror horizontal operation | Right / Left | ·
Operate with engine switch on (IG) and the vehicle stopped. ·
This test tilts the mirror right or left. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer | Buzzer built into the position control ECU and switch assembly | ON or OFF | - |