Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2013.07–2015.04
RM19V0EQ _55 Steering _014597 STEERING COLUMN _0074064 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, do not overtighten it.

·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.



PROCEDURE

Hide 1.REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Smart Entry and Start System)

a.

Using a center punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) diameter drill bit, drill a hole in each tapered-head bolt.


c.
C239333

Using a screw extractor, remove each tapered-head bolt, and then remove the steering column upper with switch bracket assembly from the steering column assembly.


Hide 45020A 2.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)

a.

Using a center punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) diameter drill bit, drill a hole in each tapered-head bolt.


c.
C236195

Using a screw extractor, remove each tapered-head bolt, and then remove the steering lock actuator assembly from the steering column assembly.


Hide 8965A 3.REMOVE POWER STEERING ECU PROTECTOR

a.
C241687

Disengage the 2 claws to remove the power steering ECU protector from the power steering ECU with motor assembly.


Hide F1901 4.REMOVE ECU WIRE SUB-ASSEMBLY

a.
C236193

Disconnect the 2 connectors from the power steering ECU with motor assembly.


b.

Disengage the 2 wire harness clamps to remove the ECU wire sub-assembly.


Hide 5.REMOVE POWER STEERING ECU WITH MOTOR ASSEMBLY

a.
C236194C10
3.145,1.516 3.302,1.661 0.156,0.145 10 *1 0.553,1.717 0.709,1.862 0.156,0.145 10 *2 2.463,1.588 3.134,1.588 false 2.211,1.9 2.847,1.9 2.847,1.9 2.847,1.588 false 1.246,1.796 0.728,1.796 false
*1 Aluminum Plate
*2 Wooden Block


Secure the steering column assembly in a vice using aluminum plates as shown in the illustration.

NOTICE:
·

Do not overtighten the vice, as the steering column assembly may become deformed.

·

Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.




b.
C236197

Disconnect the 2 connectors from the power steering ECU with motor assembly.


c.
C236198

Remove the 2 bolts and power steering ECU with motor assembly from the electric power steering column sub-assembly.


d.
C239326

Remove the O-ring from the power steering ECU with motor assembly.


Hide 89650 6.REMOVE POWER STEERING ECU ASSEMBLY

Hide 89783 7.REMOVE TRANSPONDER KEY AMPLIFIER (w/o Smart Entry and Start System)

a.
C239339

Slide the transponder key amplifier, disengage the 2 claws and then remove the transponder key amplifier as shown in the illustration.


Hide 84052 8.REMOVE UNLOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.

Insert the key.


b.
C239341

Disengage the 2 claws and slide the unlock warning switch assembly to remove it as shown in the illustration.


Hide 85432 9.REMOVE KEY INTERLOCK SOLENOID (w/o Smart Entry and Start System)

a.
C239343

Remove the screw.


b.

Disengage the claw to remove the key interlock solenoid from the steering column upper bracket assembly.


Hide 10.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Entry and Start System)

a.
C239344E01
1.59,1.942 1.758,2.087 0.168,0.145 10 *a 1.315,1.426 1.483,1.571 0.168,0.145 10 *b

C239344C01
1.604,1.917 1.844,2.094 0.24,0.177 10 *a 1.271,1.438 1.479,1.625 0.208,0.188 10 *b
*a LOCK
*b ACC


Turn the ignition switch lock cylinder assembly to the ACC position.


b.
C241164C02
1.927,0.615 1.927,0.271 1.927,0.271 1.875,0.271 false 2.021,0.625 2.021,0.219 2.021,0.219 2.75,0.219 false 1.698,0.188 1.875,0.375 0.177,0.188 10 *1 2.76,0.146 2.99,0.333 0.229,0.188 10 *2
*1 Claw
*2 Stopper
V100135

Push
V100136

Pull


Insert a screwdriver into the hole of the steering column upper bracket assembly as shown in the illustration. Pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper bracket assembly.

NOTICE:

Make sure to pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper bracket assembly. Failure to do so will affect later work operations.



c.
C239345C01
1.271,2.333 1.271,2.833 false 1.198,2.323 1.198,2.656 1.198,2.656 0.74,2.656 false 2.823,2.375 2.823,2.708 2.823,2.708 2.302,2.708 false 2.948,2.427 2.948,2.802 false 1.188,2.833 1.406,3.021 0.219,0.188 10 *1 0.552,2.583 0.75,2.781 0.198,0.198 10 *2 2.854,2.802 3.073,3.021 0.219,0.219 10 *a 2.135,2.625 2.323,2.802 0.188,0.177 10 *b
*1 Claw
*2 Stopper
*a Claw disengaged
*b Driver Insertion Hole
V100135

Tilt
V100136

Pull out


Insert a screwdriver into the hole of the steering column upper bracket assembly. Tilt the screwdriver as shown in the illustration to disengage the claw of the ignition switch lock cylinder assembly, and pull out the ignition switch lock cylinder assembly from the steering column upper bracket assembly.


Hide 84450 11.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C239347

Disengage the 2 claws to remove the ignition or starter switch assembly from the steering column upper bracket assembly.