Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2013.07
RM19V0EQ _52 Drivetrain _014585 DRIVE SHAFT / PROPELLER SHAFT _0074008 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C239401

Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C246286

Using pliers, remove the front axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
F045461C03
1.988,0.644 1.988,0.247 1.988,0.247 1.2,0.247 false 1.678,0.939 1.678,0.247 false 1.009,0.144 1.171,0.291 0.162,0.146 10 *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
F045046

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C04
2.844,1.031 1.813,1.479 1.813,1.479 2.896,1.104 false 1.625,1.396 1.896,1.646 0.271,0.25 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 6.REMOVE FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)

a.
C197577

Using pliers, remove the front drive shaft damper clamp.


b.

Remove the front drive shaft damper.


Hide 43474E 7.REMOVE FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)

a.
C292475

Using needle-nose pliers, remove the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper.


Hide 43447F 8.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C081167

Using pliers, remove the front No. 2 axle outboard joint boot clamp.


Hide 43447E 9.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the grease from the outboard joint.


Hide 41336E 11.REMOVE FRONT DRIVE SHAFT DUST COVER LH

a.
F040647N02
1.927,0.813 2.313,0.354 2.313,0.354 2.542,0.354 false 2.583,0.292 2.979,0.521 0.396,0.229 10 false SST

Using SST and a press, remove the front drive shaft dust cover LH.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.




Hide 41336D 12.REMOVE FRONT DRIVE SHAFT DUST COVER RH

a.
C067101

Using a press, remove the front drive shaft dust cover RH.

NOTICE:

Be careful not to drop the front drive inboard joint assembly.



Hide 43458 13.REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)

a.

w/ Cover:

i.
F040208N03
2,1 2,0.396 2,0.396 2.271,0.396 false 2.333,0.313 2.844,0.615 0.51,0.302 10 false SST

Using SST and a press, remove the front drive shaft dust cover.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.



HINT:

If the front drive shaft dust cover is removed, it is not necessary to reinstall it.




Hide 43410C 14.REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

a.
C092033

Using a snap ring expander, remove the drive shaft hole snap ring.


b.
F040210N02
2.052,0.813 2.052,0.292 2.052,0.292 2.542,0.292 false 2.354,1.094 2.354,0.292 false 2.583,0.208 3.083,0.49 0.5,0.281 10 false SST

Using SST and a press, remove the front drive shaft bearing.

SST
09527-10011  

NOTICE:

Be careful not to drop the front drive inboard joint assembly.