Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.05
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073985 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 31105D 1.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C201325
1.802,0.656 2.833,0.417 2.833,0.417 1.875,1.188 false 2.885,0.323 3.313,0.563 0.427,0.24 10 false SST

Using SST and a hammer, remove the front transaxle case oil seal from the transaxle housing.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07200)


Hide 31105H 2.REMOVE TRANSAXLE CASE OIL SEAL

a.
C138709
1.333,1.302 0.5,1.771 0.5,1.771 1.229,1.563 false 0.177,1.708 0.5,1.896 0.323,0.188 10 false SST

Using SST and a hammer, remove the transaxle case oil seal from the transaxle case sub-assembly.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07100)


Hide 41342A 4.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C306373

Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case.


Hide 41342F 5.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C306374

Remove the front No. 1 differential pinion shaft from the front differential case.


Hide 6.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41039A 7.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Install SST as shown in the illustration and tighten it.

C306375
4.698,0.469 4.885,0.469 4.885,0.469 5.135,0.281 false 4.385,1.51 4.802,1.51 4.802,1.51 5.042,1.375 true 4.813,1.51 5.042,1.688 true 3.188,0.208 3.5,0.406 0.313,0.198 10 false *a 1.073,2.406 1.385,2.604 0.313,0.198 10 false *b 4.396,0.396 4.854,0.594 0.458,0.198 10 false SST 4.094,1.438 4.552,1.635 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST until there is clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C306376
2.708,2.813 2.573,2.813 2.573,2.813 2.573,2.365 false 1.75,0.781 2.063,0.979 0.313,0.198 10 false *a 2.76,2.74 3.219,2.938 0.458,0.198 10 false SST
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C306377
2.219,0.177 2.406,0.177 false 2.229,1.865 2.417,1.865 false 2.219,0.333 2.438,0.333 false 2.229,1.708 2.448,1.708 false 2.219,0.563 2.563,0.563 false 2.229,1.5 2.573,1.5 false 2.042,0.094 2.354,0.292 0.313,0.198 10 false *3 2.042,1.802 2.354,2 0.313,0.198 10 false *3 2.042,0.26 2.354,0.458 0.313,0.198 10 false *2 2.042,1.646 2.354,1.844 0.313,0.198 10 false *2 2.042,0.5 2.354,0.698 0.313,0.198 10 false *1 2.042,1.438 2.354,1.635 0.313,0.198 10 false *1
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front differential case.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.



Hide 41221 8.REMOVE FRONT DIFFERENTIAL RING GEAR

a.
C306369
1.156,1.5 0.573,0.906 0.573,0.906 1.229,1.417 false 0.385,0.802 0.698,1 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front differential case.


b.
C138532

Remove the 12 bolts from the front differential ring gear.


c.
C306370

Using a plastic hammer, tap on the front differential ring gear to remove it from the front differential case.


Hide 41311E 9.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C306371
1.365,1.385 1.469,0.865 1.469,0.865 1.323,0.865 false 0.948,1.156 1.458,0.875 false 1.021,1.281 1.469,0.875 false 2.844,1.094 2.958,0.781 2.958,0.781 2.76,0.958 false 2.042,1.667 2.042,0.99 2.042,0.99 2.188,0.99 false 2.042,1.313 2.177,1.313 false 1.781,0.188 2.094,0.385 0.313,0.198 10 false *a 0.073,0.615 0.385,0.813 0.313,0.198 10 false *b 1.521,0.792 1.979,0.99 0.458,0.198 10 false SST 3.021,0.708 3.365,0.938 0.344,0.229 10 false SST 1.938,1.708 2.281,1.875 0.344,0.167 10 true SST
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing from the front differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00480)


b.
C201324
2.834,0.246 3.125,0.408 0.291,0.163 10 SST 2.816,0.329 2.701,0.329 2.701,0.329 2.357,0.568 false

Using SST, remove the front differential case front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 41311F 10.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C306372
1.031,1.063 1.385,1.063 1.385,1.063 1.063,1.396 false 0.729,1.177 1.365,1.073 false 0.781,1.365 1.375,1.073 false 2.75,0.677 3,0.563 3,0.563 2.865,0.781 false 1.979,1.302 1.979,0.854 1.979,0.854 2.146,0.854 false 1.979,1.021 2.135,1.021 false 1.448,0.99 1.906,1.188 0.458,0.198 10 false SST 3.031,0.479 3.344,0.656 0.313,0.177 10 false SST 1.875,1.333 2.188,1.51 0.313,0.177 10 true SST
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing from the front differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00480)


b.
C138536
1.49,0.635 1.979,0.635 false 2.042,0.563 2.604,0.802 0.563,0.24 10 false SST

Using SST, remove the front differential case rear tapered roller bearing outer race from the transaxle case sub-assembly.

SST
09308-00010