Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074248 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Turn Signal Switch Circuit  


DESCRIPTION

The combination meter receives the turn signal switch information and controls the turn signal lights.

WIRING DIAGRAM

E224250E35
3.594,0.594 4.292,0.76 0.698,0.167 10 false 15*1, 16*2 3.323,0.594 3.51,0.75 0.188,0.156 10 false EL 3.594,1.125 4.354,1.313 0.76,0.188 10 false 12*1, 20*2 3.302,1.125 3.51,1.281 0.208,0.156 10 false TR 3.594,1.542 4.344,1.75 0.75,0.208 10 false 11*1, 19*2 3.323,1.542 3.51,1.698 0.188,0.156 10 false TL 2.281,2.125 2.469,2.281 0.188,0.156 10 false EL 2.594,2.125 2.802,2.281 0.208,0.156 10 false TR 2.917,2.125 3.104,2.281 0.188,0.156 10 false TL 1.813,2.354 1.927,2.51 0.115,0.156 10 false R 1.813,2.594 2.156,2.75 0.344,0.156 10 false RLC 1.813,2.833 1.927,2.99 0.115,0.156 10 false N 1.813,3.073 2.083,3.229 0.271,0.156 10 false LLC 1.813,3.313 1.927,3.469 0.115,0.156 10 false L 0.74,2.396 1.469,2.76 0.729,0.365 10 false Turn Signal Switch 0.792,3.74 1.073,3.896 0.281,0.156 10 false I25 0.792,3.906 3.01,4.063 2.219,0.156 10 false Headlight Dimmer Switch Assembly 0.365,4.323 1.104,4.479 0.74,0.156 10 false *1: for LHD 1.49,4.323 2.229,4.479 0.74,0.156 10 false *2: for RHD 5.177,3.625 5.458,3.781 0.281,0.156 10 false I17 5.177,3.792 7.01,3.948 1.833,0.156 10 false Combination Meter Assembly 5.146,1.135 5.844,1.333 0.698,0.198 10 false 9*3, 3*4 5.719,1.208 6.25,1.479 0.531,0.271 10 false ER 5.083,1.542 5.688,1.74 0.604,0.198 10 false 10*3, 4*4 5.719,1.635 6.188,2.01 0.469,0.375 10 false EL 2.385,4.323 4.479,4.552 2.094,0.229 10 false *3: w/ Multi-information Display 4.406,4.333 6.5,4.563 2.094,0.229 10 false *4: w/o Multi-information Display

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Turn signal switch (Right) signal ON or OFF ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off
-
Turn Signal Switch (Left) Turn signal switch (Left) signal ON or OFF ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off
-
Body Electrical > Combination Meter > Data List
Tester Display
Turn Signal Switch (Right)
Turn Signal Switch (Left)
50003 122 98,97
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
a.

Remove the headlight dimmer switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL


b.

for LHD:

i.
E223779C01
1.833,1.406 1.573,1.854 false 2.583,1.396 2.979,1.844 false 2.417,1.396 2.552,1.844 false 0.063,0.052 0.615,0.427 0.552,0.375 10 *a 1.51,1.865 1.917,2.125 0.406,0.26 10 EL 2.406,1.865 2.896,2.115 0.49,0.25 10 TR 2.917,1.854 3.365,2.094 0.448,0.24 10 TL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
12 (TR) - 15 (EL) Turn signal switch in neutral position 10 kΩ or higher
11 (TL) - 15 (EL) Turn signal switch in neutral position 10 kΩ or higher
12 (TR) - 15 (EL) Turn signal switch in right turn position Below 1 Ω
11 (TL) - 15 (EL) Turn signal switch in left turn position Below 1 Ω




c.

for RHD:

i.
E223779C16
0.063,0.049 0.242,0.229 0.179,0.18 10 *a 0.544,1.836 0.759,1.997 0.215,0.161 10 TR 0.946,1.39 0.694,1.833 false 1.171,1.836 1.362,1.997 0.191,0.161 10 TL 1.999,1.836 2.22,1.997 0.221,0.161 10 EL 1.668,1.39 2.066,1.833 false 1.118,1.39 1.244,1.833 false
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
20 (TR) - 16 (EL) Turn signal switch in neutral position 10 kΩ or higher
19 (TL) - 16 (EL) Turn signal switch in neutral position 10 kΩ or higher
20 (TR) - 16 (EL) Turn signal switch in right turn position Below 1 Ω
19 (TL) - 16 (EL) Turn signal switch in left turn position Below 1 Ω




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I25-12 (TR) - I17-3 (ER) Always Below 1 Ω
I25-11 (TL) - I17-4 (EL) Always Below 1 Ω
I25-15 (EL) - Body ground Always Below 1 Ω
I17-3 (ER) - Body ground Always 10 kΩ or higher
I17-4 (EL) - Body ground Always 10 kΩ or higher




c.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I25-20 (TR) - I17-3 (ER)*2 Always Below 1 Ω
I25-20 (TR) - I17-9 (ER)*1 Always Below 1 Ω
I25-19 (TL) - I17-4 (EL)*2 Always Below 1 Ω
I25-19 (TL) - I17-10 (EL)*1 Always Below 1 Ω
I25-16 (EL) - Body ground*2 Always Below 1 Ω
I17-3 (ER) - Body ground*2 Always 10 kΩ or higher
I17-9 (ER) - Body ground*1 Always 10 kΩ or higher
I17-4 (EL) - Body ground*2 Always 10 kΩ or higher
I17-10 (EL) - Body ground*1 Always 10 kΩ or higher


*1: w/ Multi-information Display

*2: w/o Multi-information Display




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR