Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2015.04
RM19V0EQ _54 Brake _014594 BRAKE (REAR) _0074050 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C143446C01
2.083,1.115 1.354,1.5 1.354,1.5 2.021,1.01 true 1.188,1.438 1.417,1.635 0.229,0.198 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.

NOTICE:

When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug.


Hide 47722A 3.INSTALL DISC BRAKE CYLINDER MOUNTING

a.
C246339

Install the disc brake cylinder mounting with the 2 bolts.

Torque:
47 N*m (475 kgf*cm, 34 ft.*lbf)


Hide 47775D 4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C248020C01
0.885,1.188 0.896,1.188 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the seal surfaces of 2 new rear disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the rear disc brake cylinder slide pin.


c.

Install the rear disc brake bushing dust boot to each rear disc brake cylinder slide pin.


Hide 47715C 5.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.

Install the 2 rear disc brake cylinder slide pins to the disc brake cylinder mounting.


b.

Install the 2 rear disc brake bushing dust boots to the groove of the rear brake cylinder mounting.


Hide 04466 6.INSTALL REAR DISC BRAKE PAD

a.
C246371C01
2.427,2.854 2.594,3.021 2.594,3.021 2.708,3.021 false 0.656,0.271 0.844,0.427 0.188,0.156 10 false *A 0.667,1.906 1.01,2.156 0.344,0.25 10 false *B 2.729,2.927 2.906,3.104 0.177,0.177 10 false *1
*A Outer Side
*B Inner Side
*1 Pad Wear Indicator


Install the 2 rear disc brake pads to the disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



Hide 47850 7.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C249611C01
2.108,0.457 2.276,0.609 0.168,0.152 10 *a 3.064,0.825 3.232,0.977 0.168,0.152 10 *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)

NOTICE:

Make sure that the rear brake pad springs do not get caught at the point on the rear disc brake cylinder assembly shown in the illustration.



Hide 47319F 8.CONNECT REAR FLEXIBLE HOSE

a.
C246335C01
0.644,1.07 0.801,1.219 0.157,0.15 10 *a 2.01,1.153 0.826,1.153 false
*a Lock Hole


Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and 2 new gaskets.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 10.ADJUST PARKING BRAKE

Hide 11.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)