Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accel Request Accelerator request signal min.: -2621.44 km/h/s, max.: 2621.36 km/h/s No vehicle in front -
Vehicle Distance Millimeter wave radar sensor min.: 0 m (0 ft.), max.: 6553.5 m (21502.04 ft.) Distance to vehicle in front -
L/C Option Flag Dynamic radar cruise option flag / No or Yes No or Yes Yes: Dynamic radar cruise control system can be used
No: Dynamic radar cruise control system cannot be used
-
Car Dist Time Setting Vehicle distance time setting condition No, Long, Mid, or Shrt Vehicle-to-vehicle distance selected by vehicle-to-vehicle distance control switch -
O/D Cut Request O/D cut request Not Req or Request Not Req: Idling -
Shift Down Rqst to 3rd Shift down request to 3rd gear Not Req or Request Not Req: Idling -
Shift Down Rqst to 4th Shift down request to 4th gear Not Req or Request Not Req: Idling -
Alarm Request Shift down request to 4th gear Not Req or Request Request: When beeping
Not Req: When not beeping
-
All Throttle Close Rqst All throttle close request Not Req or Request Request: Throttle close request -
Brake Control Request Brake control request OFF or ON ON: Request
OFF: Not Req
-
Targ Decl Slope Cruise target deceleration slope 0, 1, 2, 3 0, 1, 2, 3 -
CCS Vehicle Spd Vehicle speed sensor min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
CCS Mem Vehicle Spd Cruise control memorized speed min.: 36 km/h (22 mph), max.: 200 km/h (125 mph) Memorized speed: Cruise control activated -
Throttle Opening Angle Throttle opening angle min.: 0°, max.: 124.5° Actual demanded throttle angle -
Cruise Control Dynamic radar cruise control system active condition ON or OFF ON: Cruise control activated
OFF: Cruise control deactivated
-
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-
CCS Ready M-CPU Dynamic radar cruise control system standby condition (Main CPU) ON or OFF Each time cruise control main switch is pushed, ON/OFF changes -
CCS Indicator M-CPU Cruise indicator signal (Main CPU) ON or OFF ON: Cruise control indicator on
OFF: Cruise control indicator off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Stop Light Switch 1 Stop light switch signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch 2 Stop light switch signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status Transmission range sensor signal ON or OFF ON: Shift lever in D or S
OFF: Shift lever not in D or S
-
VSC Fail Safe Flag VSC fail-safe flag Not Req or Request VSC communication fail-safe in operation -
Brake Cancel Switch Brake cancel signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
MODE Change Switch MODE switch signal ON or OFF ON: MODE switch on
OFF: MODE switch off
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


Perform Active Test according to the display on the GTS.

a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on (IG) to proceed with the Active Test using the GTS.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard

f.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


g.

Perform the Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on (IG) to proceed with the Active Test using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -