Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0073970 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

·

The ECM turns on the cruise control indicator light by sending indicator output demand signals to the combination meter assembly using CAN communication.

·

The cruise control indicator light illuminates in green when the cruise control system has been turned on using the ON-OFF switch. If a malfunction is detected, the cruise control indicator light changes to amber.

·

The cruise control indicator light circuit uses CAN communication. If the cruise control indicator light is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.


WIRING DIAGRAM

E230248E46
0.823,2.26 2.969,2.448 2.146,0.188 10 false : CAN Communication Line 4.667,0.49 4.865,0.646 0.198,0.156 10 false 13 4.927,0.667 5.344,0.823 0.417,0.156 10 false CANH 4.667,1 4.865,1.156 0.198,0.156 10 false 26 5.208,1.719 5.573,1.969 0.365,0.25 10 false A25 5.563,1.719 5.938,1.875 0.375,0.156 10 false ECM 0.958,1.719 1.177,1.875 0.219,0.156 10 false I18 1.271,1.719 3.135,1.875 1.865,0.156 10 false Combination Meter Assembly 4.927,1.167 5.344,1.323 0.417,0.156 10 false CANL 2.604,0.385 3.208,0.573 0.604,0.188 10 false 16*1 2.104,0.667 2.521,0.823 0.417,0.156 10 false CANH 2.604,0.885 3.042,1.042 0.438,0.156 10 false 15*1 2.104,1.167 2.521,1.323 0.417,0.156 10 false CANL 2.604,0.552 3.219,0.75 0.615,0.198 10 false 17*2 2.615,1.052 3.229,1.25 0.615,0.198 10 false 16*2 2.854,2.135 5.219,2.365 2.365,0.229 10 false *1: w/o TFT Multi-Information Display 2.875,2.448 5.24,2.677 2.365,0.229 10 false *2: w/ TFT Multi-Information Display

PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
Multi-information Display (Segment Type) A
Multi-information Display (TFT Type) B



A

2.PERFORM ACTIVE TEST USING GTS

B

4.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Select the following menu items: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light (illuminated in green) ON or OFF Multi-information display (Segment type)
Cruise Indicator Cruise control indicator light (illuminated in amber) ON or OFF Multi-information display (Segment type)
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Cruise
50004 122 46
Body Electrical > Combination Meter > Active Test
Tester Display
Cruise Indicator
50004 122 119

Result:
Result Proceed to
The cruise control indicator illuminates or turns off according to the operation of the Active Test. A
The cruise control indicator does not illuminate or turns off according to the operation of the Active Test. B



A

3.READ VALUE USING GTS (CCS INDICATOR M-CPU)

B

3.READ VALUE USING GTS (CCS INDICATOR M-CPU)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Indicator M-CPU Cruise control indicator light illumination signal (Main CPU) ON or OFF ON: Cruise control indicator light illuminated (green)
OFF: Cruise control indicator light not on
-
Powertrain > Cruise Control > Data List
Tester Display
CCS Indicator M-CPU
50003 237 12

Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch). A
The cruise control indicator does not illuminate but the Data List item CCS Indicator M-CPU changes according to the operation of the cruise control main switch (ON-OFF switch). B
The cruise control indicator does not illuminate and the Data List item CCS Indicator M-CPU does not change according to the operation of the cruise control main switch (ON-OFF switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

4.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All Multi-information Display (TFT Type)
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

5.READ VALUE USING GTS (CCS INDICATOR M-CPU)

B

5.READ VALUE USING GTS (CCS INDICATOR M-CPU)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Indicator M-CPU Cruise control indicator illumination signal (Main CPU) ON or OFF ON: Cruise control indicator illuminated (green)
OFF: Cruise control indicator not on
-
Powertrain > Cruise Control > Data List
Tester Display
CCS Indicator M-CPU
50003 237 12

Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch). A
The cruise control indicator does not illuminate but the Data List item CCS Indicator M-CPU changes according to the operation of the cruise control main switch (ON-OFF switch). B
The cruise control indicator does not illuminate and the Data List item CCS Indicator M- CPU does not change according to the operation of the cruise control main switch (ON-OFF switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C