Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014620 WIPER / WASHER _0074240 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the connector.


c.

Turn the ignition switch to ON.


d.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


e.

Turn the ignition switch off.


f.

Disconnect the connector.


g.
E226241C05
1.479,1.26 1.292,1.26 false 1.135,1.177 1.365,1.438 0.229,0.26 10 false *a
*a Pivot of the windshield wiper motor assembly


Apply MP grease to the pivot of the windshield wiper motor assembly.


h.
E226239C05
1.345,0.861 0.592,0.861 false 1.993,1.319 2.799,1.319 false 2.821,1.218 2.99,1.366 0.169,0.148 10 *1 0.431,0.771 0.601,0.919 0.169,0.148 10 *a
*1 No. 1 Rod
*a Pivot of the windshield wiper motor assembly


Connect the No. 1 rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)

a.
E226237C05
0.867,2.634 1.619,2.792 false 1.627,2.717 1.79,2.882 0.163,0.165 10 *1
*1 Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the connector.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

a.
E227509C03
0.991,2.665 1.694,2.784 false 1.736,2.724 1.915,2.883 0.179,0.16 10 *1
*1 Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the connector and then engage the 2 clamps.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides as shown in the illustration.

E226235


b.

Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

E226233


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.
E312135

Engage the guide and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E226523C10
1.042,1.115 0.219,1.115 false 0.052,1.01 0.417,1.333 0.365,0.323 10 false *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C10
1.958,1.115 2.26,1.115 false 2.292,1.01 2.635,1.271 0.344,0.26 10 false *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.
E226090C02
1.25,1.052 1.25,1.583 false 0.729,1.208 1.021,1.49 0.292,0.281 10 A 0.719,0.75 1.094,1.073 0.375,0.323 10 A 1.167,1.594 1.51,1.833 0.344,0.24 10 *1
*1 Ceramic Dot


Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E226523C10
1.042,1.115 0.219,1.115 false 0.052,1.01 0.417,1.333 0.365,0.323 10 false *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C10
1.958,1.115 2.26,1.115 false 2.292,1.01 2.635,1.271 0.344,0.26 10 false *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E226089C03
1.031,0.875 1.031,1.135 false 0.531,0.427 0.885,0.677 0.354,0.25 10 A 0.542,0.896 0.938,1.177 0.396,0.281 10 A 0.958,1.156 1.344,1.448 0.385,0.292 10 *1
*1 Ceramic Dot


Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



d.

Turn the engine switch on (IG).


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not come into contact with the vehicle body.


f.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


g.

Turn the ignition switch off.