1.INSTALL SLIDING ROOF HOUSING ASSEMBLY
Loosen the 4 bolts from the sliding roof housing assembly.
Install the sliding roof housing assembly with the 4 bolts and 8 nuts.
Be careful not to damage the vehicle body.
Tighten the 4 bolts to the sliding roof housing assembly.
| *1 | Clip |
| *2 | Marking |
for Clamp Type:
Insert the sliding roof drain hose.
The hose should be inserted to the base of the drain pipe.
Engage the claw to connect the sliding roof drain hose.
Make sure that the clamp is on the marking or between the marking and hose end.
Use the same procedure for the other 3 sliding roof drain hoses.
| *1 | Clip |
| *2 | Marking |
| *a | Front Side |
| *b | Outside |
for Clip Type:
Expand the clip to insert the sliding roof drain hose.
The hose should be inserted to the base of the drain pipe.
Release the clip to connect the sliding roof drain hose.
The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.
Make sure that the clip is on the marking or between the marking and hose end.
Use the same procedure for the other 3 sliding roof drain hoses.
66425B
2.INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Engage the 2 claws to install the rear No. 2 side rail spacer LH.
66415B
3.INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure as for the LH side.
62180A
4.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH (w/ Curtain Shield Airbag)
62170A
5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH (w/ Curtain Shield Airbag)
Use the same procedure as for the LH side.
63251
6.INSTALL SLIDING ROOF PANEL OR REMOVABLE ROOF WEATHERSTRIP
Install the sliding roof panel or removable roof weatherstrip as follows:
Position the joint of the weatherstrip at the rear center.
Align the alignment mark (green) on the weatherstrip with the middle marks at the corners of the sliding roof panel sub-assembly and install the weatherstrip.
Install the lip of the weatherstrip firmly.
| *A | Normal | *B | Abnormal |
| *1 | Joint | *2 | Rear |
| *3 | Alignment Mark (Green) | *4 | Middle Mark |
| *a | Pinched | *b | Exposed |
| *c | Gap (raised, wavy, etc.) | - | - |
63201G
7.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY
Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.
Perform a level check.
Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.
| Area | Measurement |
|---|---|
| A - A | 0 + 1.0 mm (0 + 0.0394 in.)
0 - 2.0 mm (0 - 0.0787 in.) |
| B - B | 0 + 2.0 mm (0 + 0.0787 in.)
0 - 1.0 mm (0 - 0.0394 in.) |
| C - C | 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.5 mm (0 - 0.0591 in.) |
| D - D | 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.0 mm (0 - 0.0394 in.) |
"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.
| *a | Even |
Perform a gap check.
Check the gap between the roof panel and roof glass.
The width must be even all around.
After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.
8. CHECK FOR WATER LEAK
After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.
If there are any leaks, readjust the sliding roof glass sub-assembly.
63218G
9.INSTALL SLIDING ROOF SIDE GARNISH LH
Engage the 2 claws to install a new sliding roof side garnish LH.
63217G
10.INSTALL SLIDING ROOF SIDE GARNISH RH
Use the same procedure as for the LH side.
11.INSTALL ROOF HEADLINING ASSEMBLY
12.RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
13.CHECK SLIDING ROOF SYSTEM