Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function) › from 2014.05
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0164269 PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function) Y

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the parking assist monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause

*: DTCs output as "Hist" will not be output again after DTCs are cleared.

Both of the following conditions are met:
·

The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced.

·

DTC C1622 is output as "Hist" only.*


The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK NAVIGATION SYSTEM (for SD)
4.CHECK NAVIGATION SYSTEM (for SD)

Result:
Result Proceed to
Navigation system (for SD) is normal A
Navigation system (for SD) is abnormal B



A

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)>DTC CHECK / CLEAR

Chassis > IPA/Parking Assist Monitor > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212

b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)>DTC CHECK / CLEAR

Chassis > IPA/Parking Assist Monitor > Clear DTCs
50002 85
Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the detection conditions of the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)>DTC CHECK / CLEAR

Chassis > IPA/Parking Assist Monitor > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

9.ADJUST, REPAIR OR REPLACE
7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING

B

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END