Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › 2014.05–2016.05
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0164321 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Speaker Circuit  


DESCRIPTION

for 6 Speakers

If there is a short in a speaker circuit, the navigation receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.


for 10 Speakers

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.


WIRING DIAGRAM

for 6 Speakers
E226481E59
5.656,7.469 6.875,7.917 1.219,0.448 10 false Navigation Receiver Assembly 3.021,1.333 4.281,2.104 1.26,0.771 10 false Front No. 2 Speaker Assembly RH 5.552,0.771 5.833,1.042 0.281,0.271 10 false 1 4.542,0.844 4.792,1.063 0.25,0.219 10 false 4 4.542,1.719 5.042,2 0.5,0.281 10 false 2 2.313,0.844 2.604,1.125 0.292,0.281 10 false 3 2.313,1.708 2.594,2.156 0.281,0.448 10 false 1 2.49,0.844 2.813,1.073 0.323,0.229 10 false + 2.5,1.688 2.708,1.927 0.208,0.24 10 false - 4.073,0.854 4.667,1.083 0.594,0.229 10 false TWR+ 4.073,1.719 4.625,1.979 0.552,0.26 10 false TWR- 5.49,0.948 5.854,1.26 0.365,0.313 10 false I64 3.021,1.156 3.281,1.313 0.26,0.156 10 false I83 0.344,1.406 1.625,2.063 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.354,1.26 0.615,1.417 0.26,0.156 10 false J5 3.021,3.313 4.313,4.021 1.292,0.708 10 false Front No. 2 Speaker Assembly LH 4.542,2.813 5,3 0.458,0.188 10 false 4 4.531,3.688 5.073,4.042 0.542,0.354 10 false 2 2.323,2.813 2.615,3.094 0.292,0.281 10 false 3 2.313,3.688 2.677,3.958 0.365,0.271 10 false 1 2.469,2.802 2.896,3.073 0.427,0.271 10 false + 2.479,3.667 2.833,3.854 0.354,0.188 10 false - 4.083,2.813 4.792,3.26 0.708,0.448 10 false TWL+ 4.104,3.688 4.708,3.948 0.604,0.26 10 false TWL- 3.042,3.156 3.302,3.313 0.26,0.156 10 false I1 0.344,3.365 1.615,4.052 1.271,0.688 10 false Front No. 1 Speaker Assembly LH 0.354,3.219 0.615,3.375 0.26,0.156 10 false K5 0.74,5.125 1.625,5.813 0.885,0.688 10 false Rear Speaker Assembly RH 0.74,4.979 1.052,5.177 0.313,0.198 10 false O18 0.74,6.677 1.604,7.344 0.865,0.667 10 false Rear Speaker Assembly LH 0.74,6.521 1.156,6.802 0.417,0.281 10 false O21 5.479,1.823 6.073,2.219 0.594,0.396 10 false I64 5.479,2.927 6.115,3.156 0.635,0.229 10 false I64 5.479,3.802 6.01,4.083 0.531,0.281 10 false I64 5.49,4.844 5.927,5.188 0.438,0.344 10 false I65 5.49,5.479 6,5.771 0.51,0.292 10 false I65 5.49,6.365 5.969,6.625 0.479,0.26 10 false I65 5.49,6.99 5.958,7.281 0.469,0.292 10 false I65 5.844,0.958 6.323,1.25 0.479,0.292 10 false FR+ 5.844,1.833 6.438,2.104 0.594,0.271 10 false FR- 5.844,2.927 6.292,3.281 0.448,0.354 10 false FL+ 5.844,3.802 6.427,4.135 0.583,0.333 10 false FL- 5.844,4.854 6.354,5.125 0.51,0.271 10 false RR+ 5.844,5.469 6.229,5.76 0.385,0.292 10 false RR- 5.844,6.344 6.219,6.656 0.375,0.313 10 false RL+ 5.844,6.979 6.104,7.135 0.26,0.156 10 false RL- 5.542,6.802 5.938,6.99 0.396,0.188 10 false 6 5.552,6.177 5.854,6.438 0.302,0.26 10 false 2 5.552,5.292 5.958,5.594 0.406,0.302 10 false 3 5.552,4.667 5.917,4.958 0.365,0.292 10 false 1 5.552,3.604 5.823,3.813 0.271,0.208 10 false 6 5.552,2.74 5.927,3.073 0.375,0.333 10 false 2 5.552,1.635 5.875,1.885 0.323,0.25 10 false 5 1.792,1.073 2.448,1.323 0.656,0.25 10 false 1 1.792,1.708 2.177,1.865 0.385,0.156 10 false 2 1.792,3.042 2.208,3.323 0.417,0.281 10 false 1 1.792,3.677 2.156,3.948 0.365,0.271 10 false 2 1.792,4.854 2.094,5.188 0.302,0.333 10 false 1 1.792,5.5 2.115,5.729 0.323,0.229 10 false 2 1.792,6.365 2.073,6.594 0.281,0.229 10 false 1 1.792,7.01 2.188,7.26 0.396,0.25 10 false 2

for 10 Speakers
E309407E04
0.531,1 1.823,1.396 1.292,0.396 10 false Front No. 1 Speaker Assembly RH 0.531,2.115 1.823,2.51 1.292,0.396 10 false Front No. 1 Speaker Assembly LH 0.344,3.26 1.635,3.656 1.292,0.396 10 false Front No. 2 Speaker Assembly RH 0.354,4.479 1.646,4.875 1.292,0.396 10 false Front No. 2 Speaker Assembly LH 0.531,0.823 0.813,1.031 0.281,0.208 10 false J5 0.531,1.948 0.813,2.156 0.281,0.208 10 false K5 0.344,3.083 0.771,3.333 0.427,0.25 10 false I84 0.354,4.302 0.792,4.552 0.438,0.25 10 false I2 1.844,0.698 2.125,0.906 0.281,0.208 10 false 1 1.865,1.385 2.146,1.594 0.281,0.208 10 false 2 1.854,1.813 2.135,2.021 0.281,0.208 10 false 1 1.875,2.5 2.156,2.708 0.281,0.208 10 false 2 2.938,2.854 3.219,3.063 0.281,0.208 10 false 4 2.938,3.469 3.219,3.677 0.281,0.208 10 false 3 2.938,4.104 3.219,4.313 0.281,0.208 10 false 4 2.938,4.74 3.219,4.948 0.281,0.208 10 false 3 5.698,0.615 5.979,0.823 0.281,0.208 10 false 15 5.708,1.24 5.99,1.448 0.281,0.208 10 false 30 5.698,1.719 5.979,1.927 0.281,0.208 10 false 11 5.708,2.365 5.99,2.573 0.281,0.208 10 false 26 5.698,2.833 5.979,3.042 0.281,0.208 10 false 12 5.698,3.469 5.938,3.688 0.24,0.219 10 false 27 5.688,4.083 5.927,4.302 0.24,0.219 10 false 14 5.688,4.719 5.927,4.938 0.24,0.219 10 false 29 5.979,0.708 6.406,0.896 0.427,0.188 10 false FR+ 5.979,1.354 6.406,1.542 0.427,0.188 10 false FR- 5.969,1.823 6.396,2.01 0.427,0.188 10 false FL+ 5.969,2.469 6.396,2.656 0.427,0.188 10 false FL- 5.958,2.927 6.385,3.115 0.427,0.188 10 false TWR+ 5.969,3.583 6.396,3.771 0.427,0.188 10 false TWR- 5.958,4.198 6.385,4.385 0.427,0.188 10 false TWL+ 5.969,4.844 6.396,5.031 0.427,0.188 10 false TWL- 5.802,5.427 7.021,5.844 1.219,0.417 10 false Stereo Component Amplifier Assembly 5.802,5.25 6.177,5.552 0.375,0.302 10 false I68

for 10 Speakers
E226483E23
5.969,0.729 6.583,1.104 0.615,0.375 10 false CTR+ 5.958,1.365 6.469,1.625 0.51,0.26 10 false CTR- 5.688,1.24 6.01,1.531 0.323,0.292 10 false 28 5.698,0.615 6.094,0.896 0.396,0.281 10 false 13 1.896,0.719 2,0.875 0.104,0.156 10 false 2 1.906,1.365 2.01,1.521 0.104,0.156 10 false 1 0.563,0.969 1.844,1.625 1.281,0.656 10 false Front No. 3 Speaker Assembly 0.573,0.781 0.979,0.99 0.406,0.208 10 false I60 5.969,1.844 6.438,2.135 0.469,0.292 10 false SR+ 5.969,2.479 6.469,2.74 0.5,0.26 10 false SR- 5.688,2.365 5.99,2.604 0.302,0.24 10 false 25 5.688,1.74 6,1.958 0.313,0.219 10 false 10 1.896,1.823 2,1.979 0.104,0.156 10 false 2 1.896,2.51 2,2.667 0.104,0.156 10 false 1 0.51,2.031 1.823,2.385 1.313,0.354 10 false Rear No. 2 Speaker Assembly RH 0.51,1.844 0.854,2 0.344,0.156 10 false O19 5.969,2.948 6.521,3.229 0.552,0.281 10 false SL+ 5.979,3.594 6.479,3.865 0.5,0.271 10 false SL- 5.698,3.458 6,3.698 0.302,0.24 10 false 24 5.76,2.823 5.948,2.979 0.188,0.156 10 false 9 1.906,2.917 2.01,3.073 0.104,0.156 10 false 2 1.906,3.594 2.01,3.75 0.104,0.156 10 false 1 0.51,3.167 1.75,3.583 1.24,0.417 10 false Rear No. 2 Speaker Assembly LH 0.5,2.99 0.833,3.146 0.333,0.156 10 false O20 5.958,4.073 6.531,4.354 0.573,0.281 10 false WF1+ 5.958,4.719 6.51,5 0.552,0.281 10 false WF1- 5.698,4.583 6.094,4.906 0.396,0.323 10 false 23 5.771,3.948 5.958,4.104 0.188,0.156 10 false 8 1.896,4.042 2,4.198 0.104,0.156 10 false 1 1.917,4.719 2.021,4.875 0.104,0.156 10 false 2 0.281,4.323 1.854,4.531 1.573,0.208 10 false Rear Speaker Assembly 0.271,4.146 0.74,4.448 0.469,0.302 10 false O22 5.833,5.115 6.5,5.563 0.667,0.448 10 false I68 5.823,5.292 7.042,5.948 1.219,0.656 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for 6 Speakers A
for 10 Speakers B




A

2.CHECK SPEAKER (OPERATION CHECK)

B

10.CHECK SPEAKER (OPERATION CHECK)
2.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly A
Rear speaker assembly B


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the I64 navigation receiver assembly connector.


b.

Disconnect the I83 and I1 front No. 2 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 2 speaker assemblies and the navigation receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-1 (FR+) - I83-4 (TWR+) Always Below 1 Ω
I64-5 (FR-) - I83-2 (TWR-) Always Below 1 Ω
I64-2 (FL+) - I1-4 (TWL+) Always Below 1 Ω
I64-6 (FL-) - I1-2 (TWL-) Always Below 1 Ω



d.

Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-1 (FR+) - Body ground Always 10 kΩ or higher
I64-5 (FR-) - Body ground Always 10 kΩ or higher
I64-2 (FL+) - Body ground Always 10 kΩ or higher
I64-6 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the J5 and K5 front No. 1 speaker assembly connectors.


b.

Disconnect the I83 and I1 front No. 2 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - I83-3 (+) Always Below 1 Ω
J5-2 - I83-1 (-) Always Below 1 Ω
K5-1 - I1-3 (+) Always Below 1 Ω
K5-2 - I1-1 (-) Always Below 1 Ω



d.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-3 (+) - Body ground Always 10 kΩ or higher
I83-1 (-) - Body ground Always 10 kΩ or higher
I1-3 (+) - Body ground Always 10 kΩ or higher
I1-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.
E226097C11
1.396,1.813 1.042,2.302 false 1.677,1.823 1.542,2.302 false 2.24,1.813 2.604,2.333 false 1.99,1.813 2.125,2.302 false 0.094,0.083 0.25,0.229 0.156,0.146 10 *a 1.5,2.313 1.656,2.458 0.156,0.146 10 + 0.656,2.313 1.26,2.542 0.604,0.229 10 TWR+*A 0.646,2.51 1.24,2.74 0.594,0.229 10 TWL+*B 1.917,2.333 2.49,2.479 0.573,0.146 10 TWR-*A 1.917,2.531 2.521,2.719 0.604,0.188 10 TWL-*B 2.646,2.313 2.76,2.458 0.115,0.146 10 -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
3 (+) - 4 (TWR+) Always Below 1 Ω
1 (-) - 2 (TWR-) Always Below 1 Ω
4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
3 (+) - 4 (TWL+) Always Below 1 Ω
1 (-) - 2 (TWL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a new or known good speaker is installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on LH and RH sides.




Result:
Proceed to
OK
NG



OK

END

NG

7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the I65 navigation receiver assembly connector.


b.

Disconnect the O18 and O21 rear speaker assembly connectors.


c.

Measure the resistance between each of the rear speaker assemblies and the navigation receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I65-1 (RR+) - O18-1 Always Below 1 Ω
I65-3 (RR-) - O18-2 Always Below 1 Ω
I65-2 (RL+) - O21-1 Always Below 1 Ω
I65-6 (RL-) - O21-2 Always Below 1 Ω



d.

Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I65-1 (RR+) - Body ground Always 10 kΩ or higher
I65-3 (RR-) - Body ground Always 10 kΩ or higher
I65-2 (RL+) - Body ground Always 10 kΩ or higher
I65-6 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR SPEAKER ASSEMBLY

b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Rear Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

10.CHECK SPEAKER (OPERATION CHECK)
a.
E273721

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly B
Front No. 3 speaker assembly C
Rear No. 2 speaker assembly D
Rear speaker assembly E


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 1 SPEAKER ASSEMBLY)

B

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

15.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)

D

17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)

E

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the I68 stereo component amplifier assembly connector.


b.

Disconnect the J5 and K5 front No. 1 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-15 (FR+) - J5-1 Always Below 1 Ω
I68-30 (FR-) - J5-2 Always Below 1 Ω
I68-11 (FL+) - K5-1 Always Below 1 Ω
I68-26 (FL-) - K5-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-15 (FR+) - Body ground Always 10 kΩ or higher
I68-30 (FR-) - Body ground Always 10 kΩ or higher
I68-11 (FL+) - Body ground Always 10 kΩ or higher
I68-26 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4.6 to 6.6 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the I68 stereo component amplifier assembly connector.


b.

Disconnect the I84 and I2 front No. 2 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-12 (TWR+) - I84-4 Always Below 1 Ω
I68-27 (TWR-) - I84-3 Always Below 1 Ω
I68-14 (TWL+) - I2-4 Always Below 1 Ω
I68-29 (TWL-) - I2-3 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-12 (TWR+) - Body ground Always 10 kΩ or higher
I68-27 (TWR-) - Body ground Always 10 kΩ or higher
I68-14 (TWL+) - Body ground Always 10 kΩ or higher
I68-29 (TWL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.
E219304C23
0.104,0.083 0.729,0.521 0.625,0.438 10 false *a
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 3 Always 3.4 to 5.2 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

15.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)
a.

Disconnect the I68 stereo component amplifier assembly connector.


b.

Disconnect the I60 front No. 3 speaker assembly connector.


c.

Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-13 (CTR+) - I60-2 Always Below 1 Ω
I68-28 (CTR-) - I60-1 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-13 (CTR+) - Body ground Always 10 kΩ or higher
I68-28 (CTR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY
a.

Remove the front No. 3 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.
E222247C32
0.208,0.229 0.521,0.427 0.313,0.198 10 false *a
*a Component without harness connected
(Front No. 3 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always 6.8 to 10.2 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the I68 stereo component amplifier assembly connector.


b.

Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.


c.

Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-10 (SR+) - O19-2 Always Below 1 Ω
I68-25 (SR-) - O19-1 Always Below 1 Ω
I68-9 (SL+) - O20-2 Always Below 1 Ω
I68-24 (SL-) - O20-1 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-10 (SR+) - Body ground Always 10 kΩ or higher
I68-25 (SR-) - Body ground Always 10 kΩ or higher
I68-9 (SL+) - Body ground Always 10 kΩ or higher
I68-24 (SL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.

Remove the rear No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL


b.
E222247C33
0.208,0.229 0.521,0.427 0.313,0.198 10 false *a
*a Component without harness connected
(Rear No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always 6.8 to 10.2 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the I68 stereo component amplifier assembly connector.


b.

Disconnect the O22 rear speaker assembly connector.


c.

Measure the resistance between the rear speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-8 (WF1+) - O22-1 Always Below 1 Ω
I68-23 (WF1-) - O22-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-8 (WF1+) - Body ground Always 10 kΩ or higher
I68-23 (WF1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT REAR SPEAKER ASSEMBLY

b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Rear Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4.8 to 6.8 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG