Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2014.05
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0164321 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

The navigation receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E268437E15
0.208,3.646 2.354,3.885 2.146,0.24 10 false Navigation Receiver Assembly 0.208,3.479 0.708,3.719 0.5,0.24 10 false I64 5.688,3.469 6,3.667 0.313,0.198 10 false I69 5.677,3.646 6.875,4.188 1.198,0.542 10 false Stereo Component Amplifier Assembly 3.26,2.74 3.969,3.01 0.708,0.271 10 false (Shielded) 0.927,0.635 1.292,0.854 0.365,0.219 10 false FR+ 0.969,1.208 1.333,1.427 0.365,0.219 10 false FR- 0.948,1.833 1.313,2.052 0.365,0.219 10 false FL+ 0.969,2.427 1.333,2.646 0.365,0.219 10 false FL- 1.344,1.104 1.5,1.333 0.156,0.229 10 false 5 1.344,0.521 1.5,0.75 0.156,0.229 10 false 1 1.354,1.708 1.51,1.938 0.156,0.229 10 false 2 1.354,2.292 1.51,2.521 0.156,0.229 10 false 6 5.76,0.521 5.917,0.75 0.156,0.229 10 false 5 5.76,1.125 5.917,1.354 0.156,0.229 10 false 4 5.76,1.708 5.917,1.938 0.156,0.229 10 false 3 5.76,2.292 5.917,2.521 0.156,0.229 10 false 2 5.75,2.875 5.906,3.104 0.156,0.229 10 false 6 6,0.625 6.313,0.823 0.313,0.198 10 false R+ 6,1.24 6.313,1.438 0.313,0.198 10 false R- 6,1.813 6.313,2.01 0.313,0.198 10 false L+ 6,2.417 6.313,2.615 0.313,0.198 10 false L- 5.99,3.021 6.344,3.219 0.354,0.198 10 false SLD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the I64 navigation receiver assembly connector.


b.

Disconnect the I69 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-1 (FR+) - I69-5 (R+) Always Below 1 Ω
I64-5 (FR-) - I69-4 (R-) Always Below 1 Ω
I64-2 (FL+) - I69-3 (L+) Always Below 1 Ω
I64-6 (FL-) - I69-2 (L-) Always Below 1 Ω
I69-5 (R+) - Body ground Always 10 kΩ or higher
I69-4 (R-) - Body ground Always 10 kΩ or higher
I69-3 (L+) - Body ground Always 10 kΩ or higher
I69-2 (L-) - Body ground Always 10 kΩ or higher
I69-6 (SLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR