Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.04
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074201 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE

a.

Apply double-sided tape as shown in the illustration.

B396395C01
0.417,7.615 6.75,8.781 6.333,1.167 4.031,8.688 4.417,8.563 false 4.313,8.01 4.698,7.906 false 2.438,0.167 2.833,0.5 0.396,0.333 12 false *A 2.438,2.76 2.917,3.083 0.479,0.323 12 false *B 2.438,5.26 2.833,5.5 0.396,0.24 12 false *C 1.083,0.667 1.479,0.917 0.396,0.25 12 false *D 0.521,7.708 0.833,7.865 0.313,0.156 10 false *a 3.885,8.604 4.198,8.76 0.313,0.156 10 false *b 1.094,8.302 1.25,8.5 0.156,0.198 10 false X 1.667,8.583 1.823,8.781 0.156,0.198 10 false Y 6.292,8.219 6.448,8.417 0.156,0.198 10 false Y 2.969,8.208 3.125,8.406 0.156,0.198 10 false Z 1.083,3.219 1.479,3.469 0.396,0.25 12 false *D 1.083,5.75 1.479,6 0.396,0.25 12 false *D 4.708,7.802 5.021,7.958 0.313,0.156 10 false *b
*A w/o Sliding Roof without Vanity Light *B w/o Sliding Roof with Vanity Light
*C w/ Sliding Roof *D w/ EC Mirror
*a Tape Attachment Location (Reference) *b Marking
V100155

Double-sided Tape - -


Double-sided Tape Size:
X:

1 mm (0.0394 in.)

Y:

10 mm (0.394 in.)

Z:

20 mm (0.787 in.)



b.

Peel off the release paper from the double-sided tape.


c.

Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.


d.

Align the pink marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.

B396394C01
1.448,2.292 1.375,2.625 true 1.448,5.229 1.344,5.521 true 1.448,8.01 1.344,8.302 true 5.573,0.75 5.042,0.979 true 5.667,1.167 5.385,1.083 true 3.75,1.167 3.5,1.25 true 4.083,1.083 3.583,1 true 3.75,4.083 3.5,4.167 true 4.083,4.021 3.583,3.938 true 5.573,3.698 5.042,3.927 true 5.667,4.104 5.385,4.021 true 6.521,6.917 6.24,6.833 true 6.438,6.552 5.906,6.781 true 3.667,7.667 3.417,7.75 true 4.5,7.417 4.021,7.563 true 0.271,0.333 0.667,0.833 0.396,0.5 12 false *A 0.271,3.333 0.667,3.667 0.396,0.333 12 false *B 0.271,6.083 0.667,6.417 0.396,0.333 12 false *C 1.302,2.625 1.615,2.781 0.313,0.156 10 false *a 3.438,0.896 3.75,1.052 0.313,0.156 10 false *b 5.594,0.656 5.906,0.813 0.313,0.156 10 false *c 3.354,1.156 3.667,1.313 0.313,0.156 10 false *d 5.75,1.76 6.063,1.917 0.313,0.156 10 false *e 1.271,5.521 1.583,5.677 0.313,0.156 10 false *a 1.271,8.313 1.583,8.469 0.313,0.156 10 false *a 5.771,4.75 6.083,4.906 0.313,0.156 10 false *e 5.771,7.5 6.083,7.656 0.313,0.156 10 false *e 5.688,1.073 6,1.229 0.313,0.156 10 false *d 3.354,4.073 3.667,4.229 0.313,0.156 10 false *d 3.438,3.833 3.75,3.99 0.313,0.156 10 false *b 5.688,4.01 6,4.167 0.313,0.156 10 false *d 5.583,3.594 5.896,3.75 0.313,0.156 10 false *c 6.438,6.448 6.75,6.604 0.313,0.156 10 false *c 6.521,6.823 6.833,6.979 0.313,0.156 10 false *d 3.281,7.667 3.594,7.823 0.313,0.156 10 false *d 4.521,7.323 4.833,7.479 0.313,0.156 10 false *b
*A w/o Sliding Roof without Vanity Light *B w/o Sliding Roof with Vanity Light
*C w/ Sliding Roof - -
*a Pink Marking Tape (A) *b Pink Marking Tape (B)
*c Pink Marking Tape (C) *d Marking
*e Adjustment Area - -



e.

w/ Vanity Light:

i.

Turn the visor connector LH clockwise approximately 45° to install it to the roof headlining assembly.



f.

Align the edge of the pink marking tape (B) on the No. 1 roof wire with the markings on the roof headlining assembly.


g.

Attach the No. 1 roof wire, starting from the pink marking tape (B) to the pink marking tape (A) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.




h.

w/ Vanity Light:

i.

Turn the visor connector RH clockwise approximately 45° to install it to the roof headlining assembly.


ii.

Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.





i.

Align the edge of the pink marking tape (C) on the No. 1 roof wire with the markings on the roof headlining assembly.


j.

Attach the No. 1 roof wire, starting from the pink marking tape (A) to the pink marking tape (C) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



k.

Apply adhesive tape between the markings on the roof headlining assembly as shown in the illustration.

B396392C01
0.833,7.802 6.333,8.802 5.5,1 4.99,8.083 5.24,8 false 4.552,8.615 4.802,8.531 false 3.083,0.167 3.458,0.49 0.375,0.323 12 false *A 3.083,2.667 3.542,2.969 0.458,0.302 12 false *B 3.167,5.25 3.5,5.521 0.333,0.271 12 false *C 1.167,2.75 1.531,3.042 0.365,0.292 12 false *D 1.448,3.073 1.833,3.417 0.385,0.344 12 false *E 1.5,5.583 1.833,5.885 0.333,0.302 12 false *F 0.938,7.917 1.25,8.073 0.313,0.156 10 false *a 4.406,8.521 4.719,8.677 0.313,0.156 10 false *b 5.25,7.896 5.563,8.052 0.313,0.156 10 false *b 2.385,8.635 2.542,8.833 0.156,0.198 10 false X 3.125,8.24 3.281,8.438 0.156,0.198 10 false Y 1.167,0.25 1.531,0.542 0.365,0.292 12 false *D
*A w/o Sliding Roof without Vanity Light *B w/o Sliding Roof with Vanity Light
*C w/ Sliding Roof *D w/ EC Mirror
*E w/o Lane Departure Alert System *F w/ Lane Departure Alert System
*a Tape Attachment Location (Reference) *b Marking
V100155

Adhesive Tape - -


Adhesive Tape Size:
X:

20 mm (0.787 in.)

Y:

80 mm (3.15 in.)



Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Digital Audio Broadcasting Antenna)

Hide 86101J 3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

Hide 63342 4.INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Align the No. 2 roof silencer pad with the markings on the roof headlining assembly and install the pad using hot-melt glue as shown in the illustration.

B396419C01
6.083,2.406 6.5,2.26 true 6.51,2.167 6.823,2.365 0.313,0.198 10 false *a
*a Marking - -
V100155

Hot-melt Glue - -


NOTICE:

Securely attach the No. 2 roof silencer pad before the hot-melt glue cools.



Hide 63341 5.INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Align the 3 No. 1 roof silencer pads with the markings on the roof headlining assembly and install the pads using hot-melt glue as shown in the illustration.

B396420C01
5.979,2.406 6.427,2.24 true 6.448,2.135 6.76,2.333 0.313,0.198 10 false *a
*a Marking - -
V100155

Hot-melt Glue - -


NOTICE:

Securely attach the No. 1 roof silencer pad before the hot-melt glue cools.



Hide 81340 6.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

a.

Install the vanity light assembly.

Click hereVehicle Interior>LIGHTING (INT)>VANITY LIGHT>INSTALLATION

HINT:

Use the same procedure for the other vanity light.