Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR › from 2015.04
RM19V0EQ _57 Power Source / Network _014602 2AR-FE BATTERY / CHARGING _0074099 GENERATOR A

2AR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A192789N02
1.615,0.792 0.552,0.792 false 1.49,1.146 0.938,1.146 0.938,1.146 0.938,0.792 false 0.198,0.708 0.51,0.896 0.313,0.188 10 SST

Using SST and a press, install a new generator drive end frame bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.
A211515C02
2.719,1.427 2.417,1.99 2.417,1.99 2.323,1.99 true 2.094,0.49 2.177,0.49 2.177,0.49 2.76,0.938 true 1.927,0.396 2.094,0.583 0.167,0.188 10 *a 2.167,1.917 2.333,2.104 0.167,0.188 10 *b
*a Tab
*b Cutout


Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A314531C07
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new bearing cover packing.

NOTICE:

Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.



b.
A192792C08
1.542,0.563 1.073,0.24 1.073,0.24 0.802,0.24 true 0.615,0.115 0.844,0.406 0.229,0.292 10 false *a
*a 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly install the generator coil assembly.


c.

Install the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C22
2.479,0.74 1.979,0.198 1.979,0.198 1.729,0.198 false 0.917,0.521 0.708,0.198 0.708,0.198 0.458,0.198 false 1.521,0.094 1.833,0.313 0.313,0.219 10 false *a 0.271,0.104 0.583,0.323 0.313,0.219 10 false *a
*a Pin (1.0 mm)


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A192793C09
1.594,0.948 2.292,0.438 2.292,0.438 2.438,0.438 true 2.49,0.344 2.74,0.615 0.25,0.271 10 false *a
*a Pin (1.0 mm)


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly hole.


Hide 27039 5.INSTALL GENERATOR REAR END COVER

a.

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



b.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 6.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator assembly in a vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch to the rotor shaft.


c.
A197238C05
1.208,0.594 1.385,0.156 1.385,0.156 1.667,0.156 true 0.427,0.948 0.427,1.563 true 1.563,1.063 1.563,1.365 false 2.521,1.427 2.771,1.427 true 1.719,0.031 2.063,0.25 0.344,0.219 10 false *a 0.271,1.594 0.833,1.833 0.563,0.24 10 false SST A 1.385,1.406 1.948,1.646 0.563,0.24 10 true SST A 2.813,1.354 3.375,1.594 0.563,0.24 10 true SST B
*a Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


d.
A333106C01
0.844,0.438 1.052,0.438 1.052,0.438 1.292,0.792 false 0.677,1 0.979,1 false 1.333,1.938 1.51,2.156 0.177,0.219 10 true *a 2.573,0.875 2.906,1.135 0.333,0.26 10 true *b 1.156,2.406 1.469,2.563 0.313,0.156 10 false *c 0.26,0.906 0.75,1.125 0.49,0.219 10 false SST A 0.406,0.333 0.896,0.552 0.49,0.219 10 false SST B
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:
·

Check that the generator assembly is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 57 N*m (581 kgf*cm, 42 ft.*lbf)




e.

Remove SST (A) and (B) from the generator pulley with clutch.


f.

Check that the generator pulley with clutch rotates smoothly.


g.

Remove the generator assembly from the vise.


Hide 27416 7.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.