Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0164656 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


E220917E02
3.497,0.109 3.894,0.347 0.397,0.238 3.599,0.155 3.828,0.337 0.23,0.182 10 I82

a.

Disconnect the I82 connector from the clearance warning ECU assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-1 (IG) - I82-30 (E) Y - BR IG power source signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I82-9 (CLSW) - I82-30 (E) B - BR Back sonar or clearance sonar switch assembly power source signal Ignition switch ON
Back sonar or clearance sonar switch assembly off
Below 1 V
Ignition switch ON
Back sonar or clearance sonar switch assembly on
11 to 14 V
I82-30 (E) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the I82 connector to the clearance warning ECU assembly.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-4 (BOF) - I82-30 (E) R - BR Power source for front sensor circuit Ignition switch off Below 1 V
Ignition switch ON, back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
I82-6 (E5) - I82-30 (E) W - BR Ground for front clearance sonar Always Below 1 V
I82-8 (SOF) - I82-30 (E) P - BR Front sensor communication signal (Front clearance sonar sensor) Ignition switch ON, back sonar or clearance sonar switch assembly on, shift lever in R Pulse generation
(Refer to waveform 1)
I82-13 (ER) - I82-30 (E) R - BR Clearance warning buzzer signal Buzzer sounding Pulse generation
(Refer to waveform 2)
I82-22 (BOR) - I82-30 (E) V - BR Power source for rear sensor circuit Ignition switch off Below 1 V
Ignition switch ON, back sonar or clearance sonar switch assembly on 7.2 to 8.8 V
I82-23 (E1) - I82-30 (E) GR - BR Ground for rear clearance sonar Always Below 1 V
I82-24 (SOR) - I82-30 (E) R - BR Rear sensor communication signal (Rear clearance sonar sensor) Ignition switch ON, back sonar or clearance sonar switch assembly on, shift lever in R Pulse generation
(Refer to waveform 1)


e.

Using an oscilloscope, check waveform 1.

i.
E231486E01
0.188,0.927 0.625,1.146 0.438,0.219 10 GND 0.188,1.542 0.719,1.792 0.531,0.25 10 GND 0.052,0.604 0.458,0.771 0.406,0.167 10 CH: 1 0.052,1.229 0.458,1.396 0.406,0.167 10 CH: 2

Waveform 1 (Reference)

Item Content
Measurement terminal
·

CH: 1 I82-8 (SOF) - I82-30 (E)

·

CH: 2 I82-24 (SOR) - I82-30 (E)


Measurement setting 5 V/DIV., 1 ms./DIV.
Condition Ignition switch ON, back sonar or clearance sonar switch assembly on, shift lever in R

HINT:

The waveforms for CH1 and CH2 are same.




f.

Using an oscilloscope, check waveform 2.

i.
E227014E01
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 2 (Reference)

Item Content
Measurement terminal I82-13 (ER) - I82-30 (E)
Measurement setting 2 V/DIV., 500 μs./DIV.
Condition Buzzer sounding
Buzzer volume M2 (Medium volume)

HINT:

The amplitude of the waveform changes according to the set volume.