Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E143732E47
5.26,5.052 7.135,5.219 1.875,0.167 10 false Combination Meter Assembly 6.146,1.292 6.427,1.448 0.281,0.156 10 false B 6.146,2.271 6.531,2.427 0.385,0.156 10 false IG+ 6.146,3.271 6.385,3.427 0.24,0.156 10 false ES 5.875,1.167 6.052,1.323 0.177,0.156 10 false 1 5.875,2.156 6.052,2.313 0.177,0.156 10 false 13 5.26,4.906 5.635,5.146 0.375,0.24 10 false I18 5.823,3 6.156,3.188 0.333,0.188 10 false 7*1 3.323,2.396 4.208,2.688 0.885,0.292 10 false METER-IG2 4.479,1.448 5.354,1.594 0.875,0.146 10 false ECU-B NO. 1 2.281,1.26 3.229,1.5 0.948,0.24 10 false from Battery 0.198,2.271 1.302,2.417 1.104,0.146 10 false from IG2 Relay 5.76,3.156 6.094,3.344 0.333,0.188 10 false 20*2 0.771,4.219 3.896,4.49 3.125,0.271 10 false *1: w/o Multi-information Display 0.781,4.688 3.906,4.958 3.125,0.271 10 false *2: w/ Multi-information Display

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY CIRCUIT)
a.
E224284C45
0.271,1.875 0.729,2.156 0.458,0.281 1.729,1.906 1.729,0.698 1.729,0.698 1.927,0.698 false 0.979,2.146 0.979,2.552 0.979,2.552 0.781,2.552 false 0.979,1.906 0.979,1.25 0.979,1.25 0.781,1.25 false 1.844,2.156 1.844,2.563 1.844,2.563 2.115,2.563 false 0.115,0.083 0.396,0.365 0.281,0.281 10 false *a 1.969,0.625 2.458,1 0.49,0.375 10 false ES*A 0.656,1.177 1.188,1.417 0.531,0.24 10 false B 0.417,1.927 0.917,2.219 0.5,0.292 10 false I18 0.542,2.479 1.073,2.719 0.531,0.24 10 false IG+ 2.198,2.479 2.688,2.854 0.49,0.375 10 false ES*B
*A w/o Multi-information Display
*B w/ Multi-information Display
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-information Display
Tester Connection Condition Specified Condition
I18-7 (ES) - Body ground Always Below 1 Ω

w/ Multi-information Display
Tester Connection Condition Specified Condition
I18-20 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I18-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR