Home › Engine / Hybrid System › CRUISE CONTROL › LANE RECOGNITION CAMERA SENSOR › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0166362 LANE RECOGNITION CAMERA SENSOR N

CRUISE CONTROL  LANE RECOGNITION CAMERA SENSOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

If the lane departure warning camera is replaced or removed and installed, or the toe-in is adjusted, perform lane departure warning camera adjustment.


PROCEDURE

Hide 86468 1.ADJUST LANE DEPARTURE WARNING CAMERA

NOTICE:
E300613C02
1.271,0.063 1.583,0.219 0.313,0.156 10 false *a 0.302,1.073 0.615,1.229 0.313,0.156 10 false *b
*a 2.0 m or more
*b 3.0 m or more


·

Make sure there are no black and white patterned objects in front of the vehicle.

·

Be sure to perform the measurement on a level surface that is free of obstacles and extends 2.0 m (6.56 ft.) or more in front of the vehicle.

·

Make sure that there is no wind when performing the measurement.

·

Check that there are no reflective materials in the surroundings or on the ground within a 3.0 m (9.84 ft.) x 3.0 m (9.84 ft.) area in front of the vehicle.

·

Perform the inspection in a bright area.



a.

Prepare for camera axis learning.

i.

Move the vehicle to a level surface.


ii.

Make sure the engine oil in the vehicle is at the specified level.


iii.

Make sure the engine coolant in the vehicle is at the specified level.


iv.

Make sure the fuel tank is full.


v.

Make sure the spare tire is in the vehicle.


vi.

Make sure the standard tools are in the vehicle.


vii.

Make sure no one is in the vehicle.


viii.

Make sure no extra loads are in the vehicle.


ix.

Adjust the tire pressures to the specified pressure.


x.

Clean the windshield.



b.

Perform front wheel alignment adjustment.

i.

Perform front wheel alignment adjustment.

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

NOTICE:

Perform this procedure as accurately as possible.




c.

Perform rear wheel alignment adjustment.

i.

Perform rear wheel alignment adjustment.

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT

NOTICE:

Perform this procedure as accurately as possible.




d.

Create a target sheet.

i.
E102781C03
0.292,2.104 0.729,2.271 0.438,0.167 10 false *a 2.781,1.042 3.063,1.313 0.281,0.271 10 false *c 0.969,2.354 1.396,2.542 0.427,0.188 10 false *b 1.333,2.802 1.865,3.021 0.531,0.219 10 false *c
*a 16 mm (0.630 in.)
*b 80 mm (3.15 in.)
*c 160 mm (6.30 in.)


Print or copy the illustration. Check that the dimensions are within +/- 5 mm (0.197 in.) of the ones in the following table.

NOTICE:
·

Make sure that the black areas of the target sheet are not glossy.

·

Make sure that the borders of the black and white areas on the target sheet are straight, and are not warped or blurry.



If the dimensions of the print or copy are not as specified, adjust settings and reprint or recopy so that the dimensions are as specified.

E144732



e.
E190544C03
1.063,0.99 0.625,1.302 false 2.292,0.927 2.698,0.688 false 2.75,0.594 3.063,0.75 0.313,0.156 10 false *a 0.458,1.229 0.771,1.385 0.313,0.156 10 false *b
*a Target Sheet
*b Cardboard


Attach the target sheet.

i.

Place the prepared target sheet on a piece of cardboard of the same size with the black area at the top right, as shown in the illustration. Then use double-sided tape to secure the target sheet in place.

NOTICE:

Do not attach reflective tape, such as transparent adhesive tape, to the target face, as this may affect target recognition.



ii.
E144727C06
0.74,2.729 1.281,2.354 false 0.719,1.406 1.24,1.135 false 1.115,2.823 1.417,3.094 0.302,0.271 10 false *b 1.313,2.26 1.563,2.469 0.25,0.208 10 false *a 1.313,1.052 1.958,1.396 0.646,0.344 10 false SST
*a Pointed Tip Weight
*b Mark-off Line


Hang a weight with a pointed tip from the center of the target sheet. Then, with double-sided tape, attach the target sheet to the reflector so that the weight aligns with the mark-off line of SST (laser radar adjusting reflector).

SST
09870-60000  (09870-60010, 09870-60020)

NOTICE:
·

Perform this procedure as accurately as possible.

·

Attach the target sheet so that it is horizontal with the ground.




iii.
E144726C05
2.042,1.76 1.177,1.76 false 2.667,1.896 3.01,2.229 0.344,0.333 10 false *a 0.875,1.677 1.26,1.865 0.385,0.188 10 false SST
*a 1350 mm (4.43 ft.)


Move the reflector up or down to position the center of the target at the height shown in the illustration and secure it in place.

SST
09870-60000  (09870-60010, 09870-60020)

NOTICE:

Perform this procedure as accurately as possible.




f.

Measure the target placement point.

NOTICE:
·

Do not place black and white patterned objects near the target.

·

Face the vehicle toward a wall with no patterns or make sure the background behind the target has no patterns.

·

Perform this procedure as accurately as possible.

·

Do not place reflective materials in the area behind the target.

·

Make sure the distance between the target and wall is within 3 m (9.84 ft.).

·

Make sure the shadow of the target is not on the wall as this may cause a recognition error.



i.

Hang a string (with weight) from the center of the vehicle rear emblem. Mark the rear center point of the vehicle on the ground.

E310465C01
2.646,2.396 3.302,2.229 false 2.646,2.479 3.063,2.531 false 4.896,0.854 5.51,0.979 true 5.5,1.438 5.896,1.51 false 5.948,1.438 6.26,1.594 0.313,0.156 10 false *a 3.344,2.135 3.656,2.292 0.313,0.156 10 false *b 4.729,0.76 5.042,0.917 0.313,0.156 10 false *c 3.104,2.448 3.417,2.604 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Point A



ii.

Repeat for the front of the vehicle.

E314795C01
1.552,0.844 2.208,0.583 true 1.552,1.5 1.948,1.542 false 3.375,2.135 4.031,2.292 false 3.583,2.448 4.031,2.375 false 2.021,1.458 2.333,1.615 0.313,0.156 10 false *a 3.208,2.042 3.521,2.198 0.313,0.156 10 false *b 2.25,0.49 2.563,0.646 0.313,0.156 10 false *c 3.427,2.365 3.74,2.521 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Point B



iii.

Using tape and a string, create a line that connects point B to point A and extends at least 2000 mm (6.56 ft.) beyond the vehicle front center point.

HINT:
·

Make sure the string is taut (using tape, etc.) when it is secured.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




iv.

Mark point C at a position 564 mm (1.85 ft.) in front of point B.

E300616C03
6.396,1.531 6.781,2.323 false 6.49,2.438 6.719,2.938 false 2.865,2.427 2.865,2.969 false 2.625,2.438 2.625,3.167 false 2.115,2.896 2.115,3.198 false 1.979,2.885 1.979,3.292 false 1.469,2.448 1.469,2.854 false 0.688,2.521 0.688,2.927 false 2.021,2.792 1.854,2.792 false 2.271,1.938 2.104,1.938 false 2.271,2.115 2.104,2.115 false 2.021,2.01 1.854,2.01 false 6.74,2.938 7.083,3.135 0.344,0.198 10 false *a 2.813,2.99 3.146,3.208 0.333,0.219 10 false *b 2.552,3.177 2.865,3.375 0.313,0.198 10 false *c 1.396,2.865 1.708,3.063 0.313,0.198 10 false *d 2.063,3.219 2.385,3.385 0.323,0.167 10 false *e 1.927,3.333 2.25,3.542 0.323,0.208 10 false *f 1.677,2.698 1.99,2.927 0.313,0.229 10 false *g 2.292,1.854 2.635,2.042 0.344,0.188 10 false *h 2.313,2.021 2.635,2.219 0.323,0.198 10 false *i 1.698,1.906 2.01,2.135 0.313,0.229 10 false *j 0.615,2.958 0.938,3.156 0.323,0.198 10 false *k 0.115,2.333 0.438,2.531 0.323,0.198 10 false *l 2.646,1.344 2.99,1.573 0.344,0.229 10 false *m 2.052,0.542 2.406,0.75 0.354,0.208 10 false *n 6.219,1.448 6.552,1.646 0.333,0.198 10 false *k
*a Point A *b Point B
*c Point C *d Point D
*e Line E *f Line F
*g Point G (Placement Point 2) *h Line H
*i Line I *j Point J (Placement Point 3)
*k Tape *l String
*m 564 mm (1.85 ft.) *n 1814 mm (5.95 ft.)



v.

Mark point D at a position 1814 mm (5.95 ft.) in front of point B.


vi.

Using a string, mark line E at a position 1000 mm (3.28 ft.) from point C.


vii.

Using a string, mark line H at a position 1000 mm (3.28 ft.) from point C.


viii.

Using a string, mark line F at a position 1000 mm (3.28 ft.) from point D.


ix.

Using a string, mark line I at a position 1000 mm (3.28 ft.) from point D.


x.

Mark point G (placement point 2) at the point where line E and line F intersect.


xi.

Mark point J (placement point 3) at the point where line H and line I intersect.


xii.

Using tape and a string, create a line that connects point G and point J (target placement line).

E300617C02
6.531,2.208 6.531,3.042 false 6.823,2.292 6.823,3.125 false 2.917,2.208 2.917,3.042 false 2.677,2.208 2.677,3.042 false 2.188,3.031 2.313,3.031 false 2.146,2.583 2.281,2.583 false 2.115,1.802 2.25,1.802 false 2.188,1.5 2.323,1.5 false 2.104,2.188 2.271,2.344 false 1.76,2.969 2.094,2.781 false 1.51,2.198 1.51,2.396 false 0.74,2.281 0.74,3.115 false 6.448,3.042 6.76,3.229 0.313,0.188 10 false *a 2.865,3.063 3.198,3.281 0.333,0.219 10 false *b 2.604,3.063 2.927,3.292 0.323,0.229 10 false *c 1.417,2.417 1.74,2.635 0.323,0.219 10 false *d 0.135,2.094 0.469,2.323 0.333,0.229 10 false *e 2.365,1.417 2.698,1.635 0.333,0.219 10 false *f 2.313,2.479 2.625,2.719 0.313,0.24 10 false *g 2.719,1.135 3.063,1.365 0.344,0.229 10 false *h 2.448,0.74 2.708,0.99 0.26,0.25 10 false *i 2.292,1.729 2.594,1.948 0.302,0.219 10 false *j 2.313,2.271 2.625,2.5 0.313,0.229 10 false *k 2.177,0.302 2.479,0.531 0.302,0.229 10 false *l 1.542,2.906 1.854,3.104 0.313,0.198 10 false *m 2.354,2.948 2.677,3.167 0.323,0.219 10 false *f 0.688,3.135 1.021,3.344 0.333,0.208 10 false *f 6.792,3.135 7.115,3.344 0.323,0.208 10 false *f 2.031,3.26 2.344,3.469 0.313,0.208 10 false *e
*a Point A *b Point B
*c Point C *d Point D
*e String *f Tape
*g Point G (Placement Point 2) *h 564 mm (1.85 ft.)
*i 1189 mm (3.90 ft.) *j Point J (Placement Point 3)
*k Point K (Placement Point 1) *l 1814 mm (5.95 ft.)
*m Target Placement Line - -



xiii.

Mark point K (placement point 1) at the intersection between the string connecting points C and D and the string connecting points G and J.


xiv.

Confirm the distance measurements for points K, G, and J (placement points 1, 2, and 3).

E300618C02
0.708,2.594 0.708,2.781 false 1.469,2.51 1.344,2.646 false 2.052,2.51 1.938,2.594 false 2.063,2.896 1.792,2.896 false 1.958,3 1.802,3.073 false 1.969,3.344 1.792,3.344 false 2.354,3.167 2.156,3 false 2.49,2.823 2.396,2.667 false 3.01,3.271 2.646,2.521 false 3.26,3.281 2.896,2.531 true 2.313,2 2.167,2 false 2.052,2.104 1.906,2.104 false 1.969,1.99 1.792,1.927 false 1.958,1.729 1.781,1.729 false 6.792,2.594 6.792,3.198 false 6.5,2.531 6.5,3.135 false 4.219,2.333 3.854,1.583 true 6.427,3.135 6.771,3.354 0.344,0.219 10 false *a 3.24,3.302 3.594,3.51 0.354,0.208 10 false *b 2.969,3.281 3.281,3.469 0.313,0.188 10 false *c 1.229,2.656 1.552,2.875 0.323,0.219 10 false *d 2.385,3.146 2.708,3.365 0.323,0.219 10 false *e 1.646,3.01 1.979,3.208 0.333,0.198 10 false *f 1.625,2.792 1.948,3 0.323,0.208 10 false *g 2.385,1.917 2.698,2.156 0.313,0.24 10 false *h 1.667,1.833 1.99,2.073 0.323,0.24 10 false *i 1.76,2 2.083,2.25 0.323,0.25 10 false *j 1.813,2.573 2.135,2.792 0.323,0.219 10 false *k 0.656,2.813 1,3.031 0.344,0.219 10 false *l 1.979,3.573 2.302,3.76 0.323,0.188 10 false *m 2.458,2.823 2.792,3.031 0.333,0.208 10 false *n 4.958,2.333 5.302,2.552 0.344,0.219 10 false *o 3.021,0.458 3.354,0.708 0.333,0.25 10 false *p 2.125,0.813 2.448,1.042 0.323,0.229 10 false *q 2.427,1.135 2.75,1.344 0.323,0.208 10 false *r 2.677,1.656 2.99,1.875 0.313,0.219 10 false *s 3.708,1.51 4.031,1.698 0.323,0.188 10 false *t 0.094,2.417 0.406,2.646 0.313,0.229 10 false *m 1.646,3.26 1.958,3.479 0.313,0.219 10 false *l 1.646,1.646 1.979,1.906 0.333,0.26 10 false *l 6.76,3.229 7.063,3.417 0.302,0.188 10 false *l
*a Point A *b Point B
*c Point C *d Point D
*e Line E *f Line F
*g Point G (Placement Point 2) *h Line H
*i Line I *j Point J (Placement Point 3)
*k Point K (Placement Point 1) *l Tape
*m String *n 1000 mm (3.28 ft.) (String)
*o 13 mm (0.512 in.) *p 3000 mm (9.84 ft.)
*q 1814 mm (5.95 ft.) *r 1189 mm (3.90 ft.)
*s 564 mm (1.85 ft.) *t Lane Departure Warning Camera Position




g.

Memorize camera/target position.

NOTICE:
·

Close all doors.

·

Perform the procedure with no one in the vehicle.

·

During the procedure, do not lean on the vehicle.

·

Do not turn on the headlights.



i.

When using the GTS:

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).*1

3.

Turn the GTS on.

4.

Enter the following menus: Chassis / Lane Departure Alert / Utility.

5.

Follow the GTS display, and continue with the adjustment.


Chassis > Lane Departure Alert > Utility
Tester Display
Recognition Camera/Target Position Memory
50005 355 2236

ii.

Input the height of the camera "1301 mm (51.2 in.)" and the horizontal position of the camera "13 mm (0.512 in.)" into the input screen. Then press the "Next" button on the display screen.


iii.

Input "3000 mm (118 in.)" for the distance from the camera to the target and "1350 mm (53.1 in.)" for the height of the target into the input screen. Then press the "Next" button on the display screen.


iv.

Input "1821 mm (71.7 in.)" for the width of the vehicle and "827 mm (32.6 in.)" for the distance between the recognition camera and the front tire into the input screen. Then press the "Next" button on the display screen.


v.

Press the "Exit" button to finish the camera/target position memory mode.

NOTICE:

If "Error Camera/target position memory" is displayed on the screen, press the "Try Again" button, and repeat from procedure *1.




h.

Perform camera axis learning.

i.

Enter the following menus: Chassis / Lane Departure Alert / Utility.*1


ii.

Follow the GTS display and continue with the adjustment.

Chassis > Lane Departure Alert > Utility
Tester Display
Recognition Camera Axis Adjust
50005 355 2237

iii.
E190547C02
1.406,0.75 0.823,1.427 false 1.385,2.052 1.698,2.208 0.313,0.156 10 false *a 1.635,2.594 1.948,2.75 0.313,0.156 10 false *b 0.917,2.938 1.229,3.094 0.313,0.156 10 false *c 1.448,0.656 1.906,0.854 0.458,0.198 10 false SST
*a Mark-off Line
*b Point K (Placement Point 1)
*c Target Placement Line


Align the target sheet with the target placement line and align the mark-off line with point K (placement point 1).


iv.

Check that the screen displays camera axis learning for target 1, then press the "Next" button on the display screen.


v.
E190547C02
1.406,0.75 0.823,1.427 false 1.385,2.052 1.698,2.208 0.313,0.156 10 false *a 1.635,2.594 1.948,2.75 0.313,0.156 10 false *b 0.917,2.938 1.229,3.094 0.313,0.156 10 false *c 1.448,0.656 1.906,0.854 0.458,0.198 10 false SST
*a Mark-off Line
*b Point G (Placement Point 2)
*c Target Placement Line


Align the target sheet with the target placement line, and align the mark-off line with point G (placement point 2).


vi.

Check that the screen displays camera axis learning for target 2, then press the "Next" button on the display screen.

NOTICE:

Within 3 minutes after the screen displays the camera axis learning for target 2, move the target and press the "Next" button on the display screen.



vii.
E190547C02
1.406,0.75 0.823,1.427 false 1.385,2.052 1.698,2.208 0.313,0.156 10 false *a 1.635,2.594 1.948,2.75 0.313,0.156 10 false *b 0.917,2.938 1.229,3.094 0.313,0.156 10 false *c 1.448,0.656 1.906,0.854 0.458,0.198 10 false SST
*a Mark-off Line
*b Point J (Placement Point 3)
*c Target Placement Line


Align the target sheet with the target placement line and align the mark-off line with point J (placement point 3).


viii.

Check that the screen displays camera axis learning for target 3 then press the "Next" button on the display screen.

NOTICE:

Within 3 minutes after the screen displays the camera axis learning for target 3, move the target and press the "Next" button on the display screen.



ix.

Press the "Exit" button to finish camera axis learning mode.

NOTICE:
If "Error camera axis adjust" is displayed on the screen, press the "Exit" button. Confirm the following conditions then turn the engine switch on (IG) and off, and repeat from procedure *1.
·

The height of the target is correct.

·

The distance from the lane departure warning camera to the target is correct.

·

The orientation of the target is correct (black area positioned at the top right).

·

The surrounding area is sufficiently bright.

·

Black and white patterned objects are not placed near the target.