Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › from 2015.04
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073982 AUTOMATIC TRANSAXLE UNIT G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35394 1.INSPECT TRANSMISSION OIL CLEANER MAGNET

a.

Examine particles in the automatic transaxle oil pan sub-assembly.

i.
C138722

Collect any steel chips with the removed magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Result:
Steel (magnetic) Brass (non-magnetic)
Bearing, gear and plate wear Bushing wear




Hide 2.INSPECT INPUT SHAFT END PLAY

a.
C136696

Using a dial indicator, measure the input shaft end play.

Standard End Play:

0.020 to 1.242 mm (0.000788 to 0.0488 in.)



Hide 3.INSPECT INTERMEDIATE SHAFT END PLAY

a.
C201496C03
3.025,0.685 3.208,0.85 0.183,0.165 10 *a
*a Dimension (A)


Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.


b.

As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension (A)).


c.
C138268C03
0.589,0.757 0.757,0.936 0.167,0.179 10 *a
*a Dimension (B)


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).


d.

Calculate the end play value using the following formula:

End play = Dimension (B) - Dimension (A) - Thrust needle roller bearing thickness

Standard End Play:

0.022 to 1.099 mm (0.000867 to 0.0432 in.)



Hide 4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C138259

Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear.

Standard Inside Diameter:

25.525 to 25.546 mm (1.00492 to 1.00575 in.)


Maximum Inside Diameter:

25.546 mm (1.00575 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear.


Hide 5.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201528

Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.

Standard Inside Diameter:

25.580 to 25.601 mm (1.00708 to 1.00791 in.)


Maximum Inside Diameter:

25.601 mm (1.00791 in.)


If the inside diameter is greater than the maximum, replace the automatic transaxle assembly.


Hide 6.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C200900

Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.

Standard Clearance:

0.18 to 0.54 mm (0.00709 to 0.0213 in.)


If the clearance is greater than the standard clearance, replace the automatic transaxle assembly.


Hide 7.INSPECT ONE-WAY CLUTCH ASSEMBLY

a.
C189425C03
0.469,1.323 0.469,1.104 0.469,1.104 1.052,0.896 false 2.469,0.802 2.125,0.802 false 2.302,0.281 2.469,0.448 0.167,0.167 10 *b 0.646,0.281 0.823,0.448 0.177,0.167 10 *a 2.51,0.719 2.688,0.885 0.177,0.167 10 *2 0.396,1.323 0.573,1.49 0.177,0.167 10 *1
*1 Planetary Ring Gear
*2 One-way Clutch Assembly
*a Free
*b Lock


Temporarily install the one-way clutch assembly to the planetary ring gear.


b.

Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the one-way clutch assembly does not operate normally, replace it.


Hide 8.INSPECT NO. 1 BRAKE DISC

a.
C203288

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 9.INSPECT NO. 2 BRAKE DISC

a.
C238852

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 10.INSPECT NO. 3 BRAKE DISC

a.
C138255

Check if the contact surfaces of the discs, plates and flanges are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 11.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C138254

Using a vernier caliper, measure the free length of the 3 2nd brake piston return spring sub-assemblies including the spring seats.

Standard Free Length:

23.26 mm (0.916 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 12.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C141533

Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly together with the spring seat.

Standard Free Length:

15.79 mm (0.622 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 13.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C201505

Using a vernier caliper, measure the free length of the No. 3 brake piston return spring sub-assembly together with the spring seat.

Standard Free Length:

9.15 mm (0.360 in.)


If the free length is shorter than the standard free length, replace the No. 3 brake piston return spring sub-assembly.


Hide 14.INSPECT CLEARANCE OF NO. 1 BRAKE

HINT:
·

Automatic transaxle assemblies manufactured at 2 different factories are available for this vehicle.

·

Refer to Introduction and check the serial number of the automatic transaxle assembly. Confirm the factory at which the automatic transaxle assembly was manufactured according to the following table.


Serial Number Factory
##T######## for TMC Made
##A######## for AISIN AW Made


a.
C309087

Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

HINT:
·

There are 6 No. 1 brake flanges of different thicknesses (for TMC Made).

·

There are 7 No. 1 brake flanges of different thicknesses (for AISIN AW Made).



No. 1 Brake Flange Thickness (for TMC Made)
Mark Thickness [mm (in.)]
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)

No. 1 Brake Flange Thickness (for AISIN AW Made)
Mark Thickness [mm (in.)]
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)
36 3.6 (0.142)


Hide 15.INSPECT CLEARANCE OF NO. 2 BRAKE

HINT:
·

Automatic transaxle assemblies manufactured at 2 different factories are available for this vehicle.

·

Refer to Introduction and check the serial number of the automatic transaxle assembly. Confirm the factory at which the automatic transaxle assembly was manufactured according to the following table.


Serial Number Factory
##T######## for TMC Made
##A######## for AISIN AW Made


a.
C238856

Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.707 to 0.974 mm (0.0278 to 0.0383 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

HINT:
·

There are 5 No. 2 brake flanges of different thicknesses (for TMC Made).

·

There are 8 No. 2 brake flanges of different thicknesses (for AISIN AW Made).



No. 2 Brake Flange Thickness (for TMC Made)
Mark Thickness [mm (in.)]
40 4.0 (0.157)
41 4.1 (0.161)
42 4.2 (0.165)
43 4.3 (0.169)
44 4.4 (0.173)

No. 2 Brake Flange Thickness (for AISIN AW Made)
Mark Thickness [mm (in.)]
40A 4.0 (0.157)
41A 4.1 (0.161)
42A 4.2 (0.165)
43A 4.3 (0.169)
44A 4.4 (0.173)
45 4.5 (0.177)
46 4.6 (0.181)
47 4.7 (0.185)


Hide 16.INSPECT CLEARANCE OF NO. 3 BRAKE

HINT:
·

Automatic transaxle assemblies manufactured at 2 different factories are available for this vehicle.

·

Refer to Introduction and check the serial number of the automatic transaxle assembly. Confirm the factory at which the automatic transaxle assembly was manufactured according to the following table.


Serial Number Factory
##T######## for TMC Made
##A######## for AISIN AW Made


a.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the No. 3 brake flange.

C319464C01
0.656,1.656 1.333,1.656 false 2.167,0.979 2.615,0.427 2.615,0.427 2.792,0.427 false 6.083,1.135 6.531,0.583 6.531,0.583 6.708,0.583 false 5.417,1.438 5.417,2.302 false 2.865,0.333 3.177,0.573 0.313,0.24 10 false *1 5.354,2.344 5.74,2.625 0.385,0.281 10 false *2 0.458,1.573 0.802,1.813 0.344,0.24 10 false *3 1.625,0.615 1.958,0.813 0.333,0.198 10 false *a 5.698,1.271 5.958,1.542 0.26,0.271 10 false *b 6.781,0.479 7.073,0.698 0.292,0.219 10 false *c
*1 Front Oil Pump Assembly *2 No. 3 Brake Piston
*3 No. 3 Brake Flange - -
*a Dimension (A) *b Dimension (B)
*c Contact Surface of Front Oil Pump Assembly - -


HINT:

Measure the distance (Dimension(A)) at 3 points where the No. 3 brake flange diameter is approximately 166 mm (6.54 in.) and calculate the average.



b.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

HINT:

Measure the distance (Dimension(B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.



c.

Calculate the clearance using the following formula:

Clearance = Dimension (B) - Dimension (A)

Standard Clearance:

0.599 to 0.799 mm (0.0236 to 0.0315 in.)


If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.


d.

Adjust clearance of No. 3 brake piston:

i.
C317753C01
1.802,1 2.135,1.656 2.135,1.656 2.281,1.656 true 2.323,1.563 2.625,1.875 0.302,0.313 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front oil pump assembly.


ii.
C317765C01
0.75,0.469 1.26,0.469 false 0.563,0.396 0.927,0.76 0.365,0.365 10 false *1
*1 No. 3 Brake Flange


Remove the No. 3 brake flange from the front oil pump assembly.


iii.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the No. 3 brake disc.

C319465C01
0.729,1.688 1.396,1.688 false 2.177,0.979 2.635,0.469 2.635,0.469 2.802,0.469 false 6.073,1.135 6.531,0.625 6.531,0.625 6.698,0.625 false 5.417,1.448 5.417,2.208 false 2.854,0.375 3.177,0.604 0.323,0.229 10 false *1 5.365,2.26 5.688,2.51 0.323,0.25 10 false *2 0.542,1.604 0.854,1.927 0.313,0.323 10 false *3 1.688,0.615 2,0.823 0.313,0.208 10 false *a 5.698,1.25 6,1.542 0.302,0.292 10 false *b 6.771,0.521 7.083,0.792 0.313,0.271 10 false *c
*1 Front Oil Pump Assembly *2 No. 3 Brake Piston
*3 No. 3 Brake Disc - -
*a Dimension (A) *b Dimension (B)
*c Contact Surface of Front Oil Pump Assembly - -


HINT:

Measure the distance (Dimension(A)) at 3 points where the No. 3 brake disc diameter is approximately 166 mm (6.54 in.) and calculate the average.



iv.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

HINT:

Measure the distance (Dimension(B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.



v.

Calculate the thickness of the replacement No. 3 brake flange using the following formula:

Thickness of Replacement No. 3 Brake Flange:

Dimension (B) - Dimension (A) - (0.599 to 0.799 mm (0.0236 to 0.0315 in.))


HINT:
·

There are 6 No. 3 brake flanges of different thicknesses (for TMC Made).

·

There are 7 No. 3 brake flanges of different thicknesses (for AISIN AW Made).



No. 3 Brake Flange Thickness (for TMC Made)
Mark Thickness [mm (in.)]
38 3.80 (0.150)
39 3.90 (0.154)
40 4.00 (0.157)
41 4.10 (0.161)
42 4.20 (0.165)
43 4.30 (0.169)

No. 3 Brake Flange Thickness (for AISIN AW Made)
Mark Thickness [mm (in.)]
38 3.80 (0.150)
39 3.90 (0.154)
40 4.00 (0.157)
41 4.10 (0.161)
42 4.20 (0.165)
43 4.30 (0.169)
44 4.40 (0.173)


vi.
C317765C01
0.75,0.469 1.26,0.469 false 0.563,0.396 0.927,0.76 0.365,0.365 10 false *1
*1 No. 3 Brake Flange


Install the No. 3 brake flange to the front oil pump assembly.


vii.
C274824N07
2.26,0.865 2.667,0.354 2.667,0.354 1.375,0.51 true 2.719,0.26 3.177,0.458 0.458,0.198 10 false A

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the front oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).





Hide 17.INSPECT CLEARANCE OF NO. 1 CLUTCH

a.
C201532

Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.


c.
C201533C03
1.094,0.271 1.198,0.271 1.198,0.271 1.406,1.042 false 0.906,0.177 1.135,0.354 0.229,0.177 10 *a
*a Feeler Gauge


Using a feeler gauge, measure the No. 1 clutch pack clearance.

HINT:

Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.


Standard Pack Clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.


Hide 18.INSPECT CLEARANCE OF NO. 2 CLUTCH

a.
C325094C01
0.406,3.667 0.583,3.667 0.583,3.667 0.719,4.146 false 0.24,3.594 0.552,3.75 0.313,0.156 10 false *1
*1 No. 2 Direct Clutch Piston


Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the diameter of the No. 2 direct clutch piston is approximately 152 mm (5.98 in.) and calculate the average.


Standard Pack Clearance:

0.394 to 0.605 mm (0.0155 to 0.0238 in.)


If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.