OVERALL CAN BUS DIAGRAM (for LHD)
The CAN communication system is composed of 1 bus.
| *1 | V Bus | *2 | V Bus Terminating Resistor |
| *3 | ECM
(for V Bus) |
*4 | Brake Actuator Assembly
(for V Bus) |
| *5 | Air Conditioning Amplifier Assembly
(for V Bus) |
*6 | ·
Navigation ECU Sub-assembly*1 ·
Radio and Display Receiver Assembly*2 (for V Bus) |
| *7 | Smart Key ECU Assembly (Certification ECU)*3
(for V Bus) |
*8 | Power Steering ECU Assembly
(for V Bus) |
| *9 | Steering Sensor*4
(for V Bus) |
*10 | Airbag Sensor Assembly
(for V Bus) |
| *11 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
*12 | DLC3
(for V Bus) |
| *13 | Combination Meter Assembly
(for V Bus) |
- | - |
*1: for Navigation Receiver Type
*2: for Radio and Display Type
*3: w/ Smart Entry and Start System
*4: w/ VSC
Refer to the following bus wiring diagrams for details.
V BUS (for LHD)
The CAN communication system connects to other networks via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
OVERALL CAN BUS DIAGRAM (for RHD)
The CAN communication system is composed of 3 buses.
| *1 | V Bus | *2 | Sub Bus 1 |
| *3 | Sub Bus 2 | *4 | V Bus Terminating Resistor |
| *5 | Sub Bus 1 Terminating Resistor | *6 | Sub Bus 2 Terminating Resistor |
| *7 | ECM
(for V Bus) |
*8 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus and Sub Bus 1) |
| *9 | Airbag Sensor Assembly
(for V Bus) |
*10 | Air Conditioning Amplifier Assembly
(for V Bus) |
| *11 | Power Steering ECU Assembly
(for V Bus) |
*12 | ·
Navigation ECU Sub-assembly*1 ·
Navigation Receiver Assembly*8 ·
Radio and Display Receiver Assembly*2 (for V Bus) |
| *13 | Network Gateway ECU*5
(for V Bus and Sub Bus 2) |
*14 | Smart Key ECU Assembly (Certification ECU)*3
(for V Bus) |
| *15 | Steering Sensor
(for V Bus) |
*16 | DLC3
(for V Bus) |
| *17 | Brake Actuator Assembly
(for V Bus) |
*18 | AFS ECU*6
(for V Bus) |
| *19 | Combination Meter Assembly
(for V Bus) |
*20 | Outer Mirror Control ECU Assembly (for Front Passenger Side)*4
(for Sub Bus 1) |
| *21 | Outer Mirror Control ECU Assembly (for Driver Side)*4
(for Sub Bus 1) |
*22 | Position Control ECU and Switch Assembly (for Driver Side)*4
(for Sub Bus 1) |
| *23 | CAN No. 4 Junction Connector*4
(for Sub Bus 1) |
*24 | Blind Spot Monitor Sensor RH*5
(for Sub Bus 2) |
| *25 | Blind Spot Monitor Sensor LH*5
(for Sub Bus 2) |
*26 | Rear Television Camera Assembly*7
(for Sub Bus 2) |
| *27 | CAN No. 7 Junction Connector*5
(for Sub Bus 2) |
- | - |
*1: for Navigation Receiver Type with HDD
*2: for Radio and Display Type
*3: w/ Smart Entry and Start System
*4: w/ Seat Position Memory System
*5: w/ Blind Spot Monitor System
*6: w/ Automatic High Beam System
*7: w/ Parking Assist Monitor System without Parallel Parking Assist Function
*8: for Navigation Receiver Type without HDD
The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
The network gateway ECU functions as a gateway between the V bus and sub bus 2.
Refer to the following bus wiring diagrams for details.
V BUS (for RHD)
The CAN communication system connects to other networks via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
SUB BUS 1 (w/ Seat Position Memory System)
SUB BUS 2 (w/ Blind Spot Monitor System)