There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. | ·
Short in CAN main bus line ·
Short in CAN branch line ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Brake actuator assembly ·
Steering sensor ·
Network gateway ECU*1 ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Smart key ECU assembly (certification ECU)*2 ·
Navigation ECU sub-assembly*3 ·
Navigation receiver assembly*6 ·
Radio and display receiver assembly*4 ·
AFS ECU*5 ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector |
*1: w/ Blind Spot Monitor System
*2: w/ Smart Entry and Start System
*3: for Navigation Receiver Type with HDD
*4: for Radio and Display Type
*5: w/ Automatic High Beam System
*6: for Navigation Receiver Type without HDD
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
After the repair, perform the CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to DLC3 |
Disconnect the I96 DLC3 branch line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I96 DLC3 branch line connector to the CAN No. 2 junction connector.
| *1 | DLC3 |
Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
While observing the resistance value shown on the tester, disconnect I95, I97, I103, I100, I107, I106, I105, I102, I112 and I161 connectors from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).
Disconnect the branch line connectors other than those of the DLC3.
| *A | w/ Automatic High Beam System | *B | w/ Smart Entry and Start System |
| *C | for Navigation Receiver Type with HDD | *D | for Radio and Display Type |
| *E | w/ Blind Spot Monitor System | *F | for Navigation Receiver Type without HDD |
| *1 | AFS ECU | *2 | Steering Sensor |
| *3 | Brake Actuator Assembly | *4 | Smart Key ECU Assembly (Certification ECU) |
| *5 | DLC3 | *6 | Combination Meter Assembly |
| *7 | Navigation ECU Sub-assembly | *8 | Radio and Display Receiver Assembly |
| *9 | ECM | *10 | Power Steering ECU Assembly |
| *11 | Airbag Sensor Assembly | *12 | Air Conditioning Amplifier Assembly |
| *13 | Main Body ECU (Multiplex Network Body ECU) | *14 | Network Gateway ECU |
| *15 | CAN No. 2 Junction Connector | *16 | CAN No. 1 Junction Connector |
| *17 | Navigation Receiver Assembly | - | - |
| *a | Component without harness connected
(CAN No. 2 Junction Connector) |
- | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Combination meter assembly | I94 | R | W |
| DLC3 | I96 | G | W |
| Smart key ECU assembly (certification ECU)*1 | I106 | L | W |
| Brake actuator assembly | I105 | Y | W |
| Steering sensor | I97 | V | W |
| AFS ECU*2 | I112 | BE | W |
*1: w/ Smart Entry and Start System
*2: w/ Automatic High Beam System
| *a | Component without harness connected
(CAN No. 1 Junction Connector) |
- | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| Network gateway ECU*3 | I161 | BE | W |
| Main body ECU (multiplex network body ECU) | I95 | P | W |
| Air conditioning amplifier assembly | I102 | V | W |
| Airbag sensor assembly | I103 | Y | W |
| Power steering ECU assembly | I100 | L | W |
| ECM | I104 | G | W |
·
Navigation ECU sub-assembly*1 ·
Navigation receiver assembly*4 ·
Radio and display receiver assembly*2 |
I107 | R | W |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |
*1: for Navigation Receiver Type with HDD
*2: for Radio and Display Type
*3: w/ Blind Spot Monitor System
*4: for Navigation Receiver Type without HDD
Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.
| Symptom | Proceed to |
|---|---|
| The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) | A |
| The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) | B |
When there is a short in one or more of the branch lines:
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
A
B
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to Combination Meter Assembly |
Disconnect the I94 combination meter assembly main bus line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Symptom | Proceed to |
|---|---|
| The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.) | A |
| The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.) | B |
A
B
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to ECM |
Disconnect the I104 ECM main bus line connector from the CAN No. 1 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
Measure the resistance with the I94 combination meter assembly main bus line connector disconnected.
| Symptom | Proceed to |
|---|---|
| The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) | A |
| The resistance becomes 1 MΩ or higher when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) | B |
A
B
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
Measure the resistance with the I94 combination meter assembly main bus line connector disconnected.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I101 CAN main bus line connector to the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
Measure the resistance with the I94 combination meter assembly main bus line connector disconnected.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I104 ECM main bus line connector to the CAN No. 1 junction connector.
Disconnect the ECM connector.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
Measure the resistance with the I94 combination meter assembly main bus line connector disconnected.
If the resistance changes to 1 MΩ or higher when the connector is disconnected, there may be a short in the ECM.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I94 combination meter assembly main bus line connector to the CAN No. 2 junction connector.
Disconnect the combination meter assembly connector.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
| Result |
|---|
| OK |
| NG |
OK
NG