Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.05–2015.04
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Brake actuator assembly

·

Steering sensor

·

Network gateway ECU*1

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (certification ECU)*2

·

Navigation ECU sub-assembly*3

·

Navigation receiver assembly*6

·

Radio and display receiver assembly*4

·

AFS ECU*5

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: w/ Blind Spot Monitor System

*2: w/ Smart Entry and Start System

*3: for Navigation Receiver Type with HDD

*4: for Radio and Display Type

*5: w/ Automatic High Beam System

*6: for Navigation Receiver Type without HDD

WIRING DIAGRAM

C247970E05
3.948,7.99 5.677,8.177 1.729,0.188 10 false : CAN Branch Line (CANH) 3.948,8.406 5.677,8.594 1.729,0.188 10 false : CAN Branch Line (CANL) 0.823,8.01 2.74,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.823,8.427 2.74,8.615 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.448,0.354 3.865,0.542 0.417,0.188 10 false 120 Ω 2.792,1 3.198,1.167 0.406,0.167 10 false CANL 1.052,4 1.458,4.167 0.406,0.167 10 false CANL 0.406,0.594 0.771,0.76 0.365,0.167 10 false I18 4.094,1.438 4.229,1.604 0.135,0.167 10 false R 2,4.073 2.167,4.24 0.167,0.167 10 false W 5.177,4.969 5.375,5.229 0.198,0.26 10 false W 3.031,1.438 3.229,1.604 0.198,0.167 10 false W 4.104,7.375 4.24,7.542 0.135,0.167 10 false B 3.031,7.375 3.198,7.542 0.167,0.167 10 false W 0.125,4.271 0.344,4.438 0.219,0.167 10 false I29 0.688,0.594 2.542,0.792 1.854,0.198 10 false Combination Meter Assembly 4.115,1 4.552,1.167 0.438,0.167 10 false CANH 1.042,3.396 1.479,3.563 0.438,0.167 10 false CANH 6.042,4.75 6.448,4.917 0.406,0.167 10 false CANL 5.865,4.427 6.302,4.594 0.438,0.167 10 false CANH 4.063,1.208 4.271,1.375 0.208,0.167 10 false 16 2.698,5.354 2.906,5.521 0.208,0.167 10 false 1 2.698,6.073 2.906,6.24 0.208,0.167 10 false 2 2.729,3.313 2.938,3.479 0.208,0.167 10 false 1 2.729,4.083 2.938,4.25 0.208,0.167 10 false 2 1.542,3.406 1.75,3.573 0.208,0.167 10 false 3 4.479,2.979 4.583,3.146 0.104,0.167 10 false 2 1.563,3.979 1.771,4.146 0.208,0.167 10 false 2 4.479,4.271 4.688,4.438 0.208,0.167 10 false 1 4.479,4.99 4.688,5.156 0.208,0.167 10 false 2 2,3.313 2.229,3.479 0.229,0.167 10 false V 2.938,1.813 3.063,1.979 0.125,0.167 10 false 2 3.031,1.208 3.219,1.375 0.188,0.167 10 false 15 4.49,2.219 4.604,2.385 0.115,0.167 10 false 1 4.25,1.802 4.365,1.969 0.115,0.167 10 false 1 2.938,7.125 3.063,7.292 0.125,0.167 10 false 2 4.25,7.125 4.365,7.292 0.115,0.167 10 false 1 5.802,4.885 6,5.052 0.198,0.167 10 false 14 5.656,4.354 5.833,4.521 0.177,0.167 10 false 6 5.156,0.458 6.365,0.646 1.208,0.188 10 false x: Suspected Area 6.083,4.99 6.406,5.177 0.323,0.188 10 false I39 6.365,4.99 6.76,5.177 0.396,0.188 10 false DLC3 0.406,4.271 1.479,4.479 1.073,0.208 10 false Steering Sensor 0.844,2.177 2.833,2.427 1.99,0.25 10 false CAN No. 2 Junction Connector 5.177,4.25 5.365,4.5 0.188,0.25 10 false G 2.615,5.896 2.906,6.083 0.292,0.188 10 false I105 2.615,5.531 2.906,5.719 0.292,0.188 10 false I105 2.667,3.865 2.885,4.052 0.219,0.188 10 false I97 2.667,3.521 2.885,3.708 0.219,0.188 10 false I97 3.177,1.823 3.406,2.01 0.229,0.188 10 false I94 3.948,1.823 4.167,2.01 0.219,0.188 10 false I94 4.417,2.417 4.708,2.604 0.292,0.188 10 false I106 4.417,2.781 4.708,2.969 0.292,0.188 10 false I106 4.438,4.448 4.656,4.635 0.219,0.188 10 false I96 4.438,4.802 4.656,4.99 0.219,0.188 10 false I96 3.146,7.094 3.448,7.281 0.302,0.188 10 false I101 3.896,7.094 4.198,7.281 0.302,0.188 10 false I101 0.406,6.344 2.208,6.698 1.802,0.354 10 false Brake Actuator Assembly 1.063,6 1.469,6.167 0.406,0.167 10 false CANL 1.052,5.448 1.49,5.615 0.438,0.167 10 false CANH 2.302,5.333 2.448,5.5 0.146,0.167 10 false Y 2.302,6.083 2.448,6.25 0.146,0.167 10 false W 1.729,5.333 1.958,5.5 0.229,0.167 10 false GR 1.771,6.083 1.917,6.25 0.146,0.167 10 false W 0.125,6.344 0.427,6.521 0.302,0.177 10 false A49 1.531,5.417 1.823,5.646 0.292,0.229 10 false 26 1.531,6.031 1.719,6.198 0.188,0.167 10 false 14 5.823,2.875 6.229,3.042 0.406,0.167 10 false CANL 5.823,2.302 6.26,2.469 0.438,0.167 10 false CANH 5.115,2.25 5.26,2.417 0.146,0.167 10 false L 5.115,2.979 5.26,3.146 0.146,0.167 10 false W 5.573,2.323 5.76,2.49 0.188,0.167 10 false 14 5.583,2.875 5.771,3.042 0.188,0.167 10 false 15 4.969,3.156 5.229,3.323 0.26,0.167 10 false I78 5.25,3.156 6.948,3.563 1.698,0.406 10 false Smart Key ECU Assembly (Certification ECU)*1 0.188,6.854 2.49,7.125 2.302,0.271 10 false *1: w/ Smart Entry and Start System 0.188,7.177 2.635,7.646 2.448,0.469 10 false *2: w/ Automatic High Beam System 4.5,6.083 4.708,6.25 0.208,0.167 10 false 1 4.5,6.823 4.708,6.99 0.208,0.167 10 false 2 4.406,6.646 4.698,6.833 0.292,0.188 10 false I112 4.406,6.281 4.698,6.469 0.292,0.188 10 false I112 4.833,6.052 5.063,6.219 0.229,0.167 10 false BE 4.865,6.865 5.01,7.031 0.146,0.167 10 false W 5.417,6.052 5.646,6.219 0.229,0.167 10 false B 5.417,6.854 5.563,7.021 0.146,0.167 10 false W 5.865,6.167 6.302,6.333 0.438,0.167 10 false MPX1 5.813,7.083 6.135,7.271 0.323,0.188 10 false A35 6.094,7.083 6.927,7.333 0.833,0.25 10 false AFS ECU*2 5.865,6.781 6.302,6.948 0.438,0.167 10 false MPX2 5.604,6.135 5.792,6.302 0.188,0.167 10 false 12 5.604,6.792 5.823,6.99 0.219,0.198 10 false 13

C325777E01
0.313,2.302 2.458,2.583 2.146,0.281 10 false Navigation ECU Sub-assembly*1 0.302,2.656 2.448,2.938 2.146,0.281 10 false Navigation Receiver Assembly*4 0.302,3 2.01,3.396 1.708,0.396 10 false Radio and Display Receiver Assembly*2 0.313,4.677 1.865,5.083 1.552,0.406 10 false Air Conditioning Amplifier Assembly 0.313,6.427 2.458,6.708 2.146,0.281 10 false Network Gateway ECU*3 5.802,1.698 7.115,2.094 1.313,0.396 10 false Power Steering ECU Assembly 5.615,3.615 7.156,3.896 1.542,0.281 10 false Airbag Sensor Assembly 5.521,5.427 7.156,5.833 1.635,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 4.729,8.396 5.271,8.656 0.542,0.26 10 false ECM 4.427,6.146 6.573,6.427 2.146,0.281 10 false CAN No. 1 Junction Connector 0.073,2.302 0.521,2.49 0.448,0.188 10 false I67 0.073,2.646 0.521,2.833 0.448,0.188 10 false I67 0.021,3 0.469,3.188 0.448,0.188 10 false I155 0.063,4.688 0.51,4.875 0.448,0.188 10 false I77 0.031,6.427 0.479,6.615 0.448,0.188 10 false I160 5.573,1.698 6.021,1.885 0.448,0.188 10 false j1 5.385,3.615 5.833,3.802 0.448,0.188 10 false I47 5.26,5.438 5.708,5.625 0.448,0.188 10 false I13 4.74,8.188 5.188,8.375 0.448,0.188 10 false A25 1.021,1.396 1.469,1.583 0.448,0.188 10 false CANH 1.031,1.99 1.479,2.177 0.448,0.188 10 false CANL 1.042,3.75 1.49,3.938 0.448,0.188 10 false CANH 1.083,4.365 1.531,4.552 0.448,0.188 10 false CANL 1.031,5.521 1.479,5.708 0.448,0.188 10 false CA1H 1.063,6.104 1.51,6.292 0.448,0.188 10 false CA1L 5.823,0.823 6.271,1.01 0.448,0.188 10 false CANH 5.844,1.427 6.292,1.615 0.448,0.188 10 false CANL 5.823,2.698 6.271,2.885 0.448,0.188 10 false CANH 5.844,3.292 6.292,3.479 0.448,0.188 10 false CANL 5.823,4.583 6.271,4.771 0.448,0.188 10 false CANH 5.844,5.156 6.292,5.344 0.448,0.188 10 false CANL 3.917,0.563 4.365,0.75 0.448,0.188 10 false I93 3.156,0.563 3.604,0.75 0.448,0.188 10 false I93 2.594,1.5 3.042,1.688 0.448,0.188 10 false I107 2.594,1.875 3.042,2.063 0.448,0.188 10 false I107 2.583,3.875 3.031,4.063 0.448,0.188 10 false I102 2.583,4.24 3.031,4.427 0.448,0.188 10 false I102 2.604,5.625 3.052,5.813 0.448,0.188 10 false I161 2.594,5.99 3.042,6.177 0.448,0.188 10 false I161 4.396,0.938 4.844,1.125 0.448,0.188 10 false I100 4.406,1.313 4.854,1.5 0.448,0.188 10 false I100 4.385,2.823 4.833,3.01 0.448,0.188 10 false I103 4.385,3.188 4.833,3.375 0.448,0.188 10 false I103 4.427,4.656 4.875,4.844 0.448,0.188 10 false I95 4.427,5.031 4.875,5.219 0.448,0.188 10 false I95 3.875,6.51 4.323,6.698 0.448,0.188 10 false I104 3.115,6.521 3.563,6.708 0.448,0.188 10 false I104 4.073,8.083 4.521,8.271 0.448,0.188 10 false CANH 2.771,8.073 3.219,8.26 0.448,0.188 10 false CANL 1.521,1.375 1.969,1.563 0.448,0.188 10 false 9 1.521,2 1.969,2.188 0.448,0.188 10 false 10 1.521,3.76 1.969,3.948 0.448,0.188 10 false 11 1.542,4.365 1.99,4.552 0.448,0.188 10 false 12 1.531,5.521 1.979,5.708 0.448,0.188 10 false 16 1.521,6.094 1.969,6.281 0.448,0.188 10 false 15 5.646,0.823 6.094,1.01 0.448,0.188 10 false 4 5.635,1.427 6.083,1.615 0.448,0.188 10 false 8 5.531,2.698 5.979,2.885 0.448,0.188 10 false 13 5.552,3.313 6,3.5 0.448,0.188 10 false 22 5.542,4.583 5.99,4.771 0.448,0.188 10 false 14 5.563,5.146 6.01,5.333 0.448,0.188 10 false 13 4.073,7.865 4.521,8.052 0.448,0.188 10 false 13 2.958,7.854 3.406,8.042 0.448,0.188 10 false 26 4.24,0.542 4.688,0.729 0.448,0.188 10 false 1 2.917,0.531 3.365,0.719 0.448,0.188 10 false 2 2.667,1.292 3.115,1.479 0.448,0.188 10 false 1 2.677,2.073 3.125,2.26 0.448,0.188 10 false 2 2.677,3.677 3.125,3.865 0.448,0.188 10 false 1 2.677,4.448 3.125,4.635 0.448,0.188 10 false 2 2.688,6.177 3.135,6.365 0.448,0.188 10 false 2 4.479,0.708 4.927,0.896 0.448,0.188 10 false 1 4.479,1.531 4.927,1.719 0.448,0.188 10 false 2 4.469,2.604 4.917,2.792 0.448,0.188 10 false 1 4.469,3.385 4.917,3.573 0.448,0.188 10 false 2 4.469,4.448 4.917,4.635 0.448,0.188 10 false 1 4.49,5.24 4.938,5.427 0.448,0.188 10 false 2 4.26,6.542 4.708,6.729 0.448,0.188 10 false 1 2.688,5.406 3.135,5.594 0.448,0.188 10 false 1 2.906,6.521 3.354,6.708 0.448,0.188 10 false 2 2.073,1.313 2.521,1.5 0.448,0.188 10 false R 2.073,2.094 2.521,2.281 0.448,0.188 10 false W 2.083,3.688 2.531,3.875 0.448,0.188 10 false V 2.073,4.469 2.521,4.656 0.448,0.188 10 false W 2.042,5.417 2.49,5.604 0.448,0.188 10 false BE 2.073,6.25 2.521,6.438 0.448,0.188 10 false W 4.938,0.75 5.385,0.938 0.448,0.188 10 false L 4.948,1.552 5.396,1.74 0.448,0.188 10 false W 5.448,0.75 5.896,0.938 0.448,0.188 10 false Y 5.448,1.542 5.896,1.729 0.448,0.188 10 false SB 5.156,2.583 5.604,2.771 0.448,0.188 10 false Y 5.146,3.406 5.594,3.594 0.448,0.188 10 false W 5.156,4.458 5.604,4.646 0.448,0.188 10 false P 5.146,5.24 5.594,5.427 0.448,0.188 10 false W 4.146,6.958 4.594,7.146 0.448,0.188 10 false G 2.958,6.948 3.406,7.135 0.448,0.188 10 false W 4.135,7.51 4.583,7.698 0.448,0.188 10 false B 2.969,7.531 3.417,7.719 0.448,0.188 10 false W 3.438,8.698 3.885,8.885 0.448,0.188 10 false 120 Ω 0.083,6.823 2.781,7.052 2.698,0.229 10 false *1: for Navigation Receiver Type with HDD 0.083,7.219 2.781,7.448 2.698,0.229 10 false *2: for Radio and Display Type 0.094,7.625 2.792,7.854 2.698,0.229 10 false *3: w/ Blind Spot Monitor System 0.094,8.021 2.042,8.375 1.948,0.354 10 false *4: for Navigation Receiver Type without HDD 0.104,8.698 2.802,8.927 2.698,0.229 10 false x: Suspected Area 0.813,9.052 3.51,9.281 2.698,0.229 10 false : CAN Main Bus Line (CANH) 0.823,9.427 3.521,9.656 2.698,0.229 10 false : CAN Main Bus Line (CANL) 3.99,9.063 6.688,9.292 2.698,0.229 10 false : CAN Branch Line (CANH) 4.01,9.469 6.708,9.698 2.698,0.229 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform the CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C247973C01
1.469,1.688 1.854,1.927 0.385,0.24 2.302,2.25 2.583,2.063 2.583,2.063 2.677,2.063 false 2.313,2.438 2.594,2.583 2.594,2.583 2.688,2.583 false 2.063,2.323 1.896,2.146 1.896,2.146 1.708,2.146 false 2.156,2.448 1.896,2.854 1.896,2.854 1.781,2.854 false 0.083,0.073 0.333,0.271 0.25,0.198 10 false *a 2.708,1.99 3.281,2.229 0.573,0.24 10 false CANH*b 2.719,2.51 3.271,2.74 0.552,0.229 10 false CANL*b 1.573,2.073 1.729,2.26 0.156,0.188 10 false G 1.625,2.792 1.844,2.979 0.219,0.188 10 false W 1.563,1.729 1.771,1.917 0.208,0.188 10 false I96
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to DLC3


Disconnect the I96 DLC3 branch line connector from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C14
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 false 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 false 2.51,2.354 2.938,2.354 false 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Reconnect the I96 DLC3 branch line connector to the CAN No. 2 junction connector.


b.

Disconnect the connectors from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.

HINT:

Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.



c.
C210421C15
1.51,0.698 1.948,1 0.438,0.302 2.073,1.854 2.219,1.302 2.219,1.302 2.438,1.302 false 2.083,2.531 2.208,3 2.208,3 2.365,3 false 2.51,2.323 2.938,2.323 false 0.104,0.104 0.948,0.438 0.844,0.333 10 false *1 1.625,0.76 1.938,0.938 0.313,0.177 10 false I39 2.49,1.208 2.896,1.385 0.406,0.177 10 false CANH 2.438,2.927 2.823,3.104 0.385,0.177 10 false CANL 2.958,2.24 3.292,2.406 0.333,0.167 10 false BAT
*1 DLC3


Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

C324660C01
3.438,0.344 3.896,0.542 0.458,0.198 10 false *15 0.156,1.083 0.469,1.281 0.313,0.198 10 false BE 0.229,1.854 0.542,2.052 0.313,0.198 10 false B 0.76,1.104 0.917,1.302 0.156,0.198 10 false W 0.75,1.854 0.906,2.052 0.156,0.198 10 false W 0.354,2.406 1.271,2.604 0.917,0.198 10 false *1 (*A) 1.24,1.104 1.396,1.302 0.156,0.198 10 false V 1.74,1.104 1.896,1.302 0.156,0.198 10 false W 2.26,1.104 2.417,1.302 0.156,0.198 10 false Y 2.188,1.854 2.5,2.052 0.313,0.198 10 false GR 2.781,1.104 2.938,1.302 0.156,0.198 10 false W 2.792,1.854 2.948,2.052 0.156,0.198 10 false W 1.448,1.688 1.76,1.885 0.313,0.198 10 false *2 2.5,2.385 2.813,2.583 0.313,0.198 10 false *3 3.646,1.667 4.563,1.865 0.917,0.198 10 false *4 (*B) 3.521,1.115 3.677,1.313 0.156,0.198 10 false L 4.021,1.115 4.177,1.313 0.156,0.198 10 false W 4.521,1.521 4.677,1.719 0.156,0.198 10 false G 5.031,1.521 5.188,1.719 0.156,0.198 10 false W 4.771,2.385 5.083,2.583 0.313,0.198 10 false *5 5.792,1.677 6.104,1.875 0.313,0.198 10 false *6 5.542,1.115 5.698,1.313 0.156,0.198 10 false R 6.052,1.115 6.208,1.313 0.156,0.198 10 false W 6.344,2.698 6.5,2.896 0.156,0.198 10 false B 6.885,2.698 7.042,2.896 0.156,0.198 10 false W 0.094,3.521 0.25,3.719 0.156,0.198 10 false B 0.552,3.521 0.708,3.719 0.156,0.198 10 false W 0.844,3.781 1.917,3.979 1.073,0.198 10 false *7 (*C) 0.854,4.01 1.927,4.208 1.073,0.198 10 false *8 (*D) 0.802,4.26 1.875,4.458 1.073,0.198 10 false *17 (*F) 0.719,5.146 0.875,5.344 0.156,0.198 10 false R 1.26,5.146 1.417,5.344 0.156,0.198 10 false W 1.917,4.865 2.229,5.063 0.313,0.198 10 false *9 1.667,5.24 1.823,5.438 0.156,0.198 10 false B 2.208,5.24 2.365,5.438 0.156,0.198 10 false W 1.667,5.677 1.823,5.875 0.156,0.198 10 false G 2.219,5.698 2.375,5.896 0.156,0.198 10 false W 2.875,4.229 3.333,4.427 0.458,0.198 10 false *10 2.667,4.792 2.823,4.99 0.156,0.198 10 false Y 3.188,4.792 3.5,4.99 0.313,0.198 10 false SB 2.708,5.552 2.865,5.75 0.156,0.198 10 false L 3.198,5.563 3.354,5.76 0.156,0.198 10 false W 3.844,4.885 4.302,5.083 0.458,0.198 10 false *11 4.885,4.219 5.344,4.417 0.458,0.198 10 false *12 3.677,5.563 3.833,5.76 0.156,0.198 10 false Y 4.688,5.167 4.844,5.365 0.156,0.198 10 false V 4.156,5.563 4.313,5.76 0.156,0.198 10 false W 5.188,5.167 5.344,5.365 0.156,0.198 10 false W 5.677,4.885 6.135,5.083 0.458,0.198 10 false *13 6.438,4.219 7.115,4.448 0.677,0.229 10 false *14 (*E) 5.469,5.573 5.625,5.771 0.156,0.198 10 false P 5.979,5.573 6.135,5.771 0.156,0.198 10 false W 6.302,5.167 6.615,5.365 0.313,0.198 10 false BE 6.906,5.177 7.063,5.375 0.156,0.198 10 false W 3.469,6.281 3.927,6.479 0.458,0.198 10 false *16
*A w/ Automatic High Beam System *B w/ Smart Entry and Start System
*C for Navigation Receiver Type with HDD *D for Radio and Display Type
*E w/ Blind Spot Monitor System *F for Navigation Receiver Type without HDD
*1 AFS ECU *2 Steering Sensor
*3 Brake Actuator Assembly *4 Smart Key ECU Assembly (Certification ECU)
*5 DLC3 *6 Combination Meter Assembly
*7 Navigation ECU Sub-assembly *8 Radio and Display Receiver Assembly
*9 ECM *10 Power Steering ECU Assembly
*11 Airbag Sensor Assembly *12 Air Conditioning Amplifier Assembly
*13 Main Body ECU (Multiplex Network Body ECU) *14 Network Gateway ECU
*15 CAN No. 2 Junction Connector *16 CAN No. 1 Junction Connector
*17 Navigation Receiver Assembly - -


C247977C01
3.583,2.302 3.875,2.469 0.292,0.167 10 false I101 3.615,2.573 3.833,2.74 0.219,0.167 10 false I94 3.583,3.406 3.875,3.573 0.292,0.167 10 false I105 3.615,2.854 3.833,3.021 0.219,0.167 10 false I96 3.583,3.135 3.875,3.302 0.292,0.167 10 false I106 3.615,3.708 3.833,3.875 0.219,0.167 10 false I97 2.333,0.427 2.594,0.677 0.26,0.25 10 false *a 3.583,4 3.875,4.167 0.292,0.167 10 false I112
*a Component without harness connected
(CAN No. 2 Junction Connector)
- -


Wiring Color:
CAN No. 2 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I101 B W
Combination meter assembly I94 R W
DLC3 I96 G W
Smart key ECU assembly (certification ECU)*1 I106 L W
Brake actuator assembly I105 Y W
Steering sensor I97 V W
AFS ECU*2 I112 BE W


*1: w/ Smart Entry and Start System

*2: w/ Automatic High Beam System


C247978C01
3.354,2.604 3.802,2.771 0.448,0.167 10 false I95 3.313,2.323 3.76,2.49 0.448,0.167 10 false I161 3.313,3.156 3.76,3.323 0.448,0.167 10 false I103 3.313,2.875 3.76,3.042 0.448,0.167 10 false I102 3.344,4.25 3.792,4.417 0.448,0.167 10 false I93 3.313,3.979 3.76,4.146 0.448,0.167 10 false I107 3.313,3.438 3.76,3.604 0.448,0.167 10 false I100 2.427,0.385 2.625,0.583 0.198,0.198 10 false *a 3.313,3.708 3.76,3.875 0.448,0.167 10 false I104
*a Component without harness connected
(CAN No. 1 Junction Connector)
- -


Wiring Color:
CAN No. 1 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Network gateway ECU*3 I161 BE W
Main body ECU (multiplex network body ECU) I95 P W
Air conditioning amplifier assembly I102 V W
Airbag sensor assembly I103 Y W
Power steering ECU assembly I100 L W
ECM I104 G W
·

Navigation ECU sub-assembly*1

·

Navigation receiver assembly*4

·

Radio and display receiver assembly*2


I107 R W
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I93 B W


*1: for Navigation Receiver Type with HDD

*2: for Radio and Display Type

*3: w/ Blind Spot Monitor System

*4: for Navigation Receiver Type without HDD


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.



Result:
Symptom Proceed to
The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) A
The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher ) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) B


d.

When there is a short to +B in one or more of the bus lines that connect to an ECU (or sensor):

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or higher ) to confirm that there is a short to +B in the one bus line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.





e.

When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:

i.

With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.




A

3.CHECK CAN NO. 2 JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
3.CHECK CAN NO. 2 JUNCTION CONNECTOR
a.
C251600C01
2.74,1.271 3.125,1.531 0.385,0.26 2.875,2.135 2.417,1.719 2.417,1.719 2.167,1.719 false 2.875,2.354 2.875,2.698 2.875,2.698 2.198,2.698 false 2.729,2.229 2.458,1.896 2.458,1.896 2.323,1.896 false 2.792,2.344 2.531,2.198 2.531,2.198 2.406,2.198 false 0.135,0.125 0.479,0.375 0.344,0.25 10 false *a 1.646,1.646 2.292,1.865 0.646,0.219 10 false CANH*b 1.552,2.521 2.198,2.74 0.646,0.219 10 false CANL*b 2.198,1.823 2.365,2.031 0.167,0.208 10 false B 2.219,2.135 2.385,2.344 0.167,0.208 10 false W 2.802,1.313 3.104,1.521 0.302,0.208 10 false I101
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector


Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C16
1.51,0.698 1.948,1 0.438,0.302 2.073,1.823 2.26,1.302 2.26,1.302 2.438,1.302 false 2.083,2.531 2.208,2.969 2.208,2.969 2.375,2.969 false 2.51,2.323 2.938,2.323 false 0.104,0.094 0.948,0.427 0.844,0.333 10 false *1 1.625,0.76 1.938,0.938 0.313,0.177 10 false I39 2.49,1.229 2.896,1.406 0.406,0.177 10 false CANH 2.438,2.885 2.823,3.063 0.385,0.177 10 false CANL 2.958,2.24 3.292,2.406 0.333,0.167 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

4.CHECK CAN NO. 1 JUNCTION CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

NG

REPLACE CAN NO. 2 JUNCTION CONNECTOR

4.CHECK CAN NO. 1 JUNCTION CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the I101 CAN main bus line connector to the CAN No. 2 junction connector.


b.
C247984C01
2.719,1.375 3.177,1.656 0.458,0.281 2.875,2.146 2.417,1.854 2.417,1.854 2.167,1.854 false 2.875,2.365 2.875,2.698 2.875,2.698 2.198,2.698 false 2.74,2.219 2.438,2.083 2.438,2.083 2.302,2.083 false 2.813,2.333 2.365,2.333 false 0.094,0.094 0.375,0.302 0.281,0.208 10 false *a 1.635,1.781 2.281,2 0.646,0.219 10 false CANH*b 1.667,2.625 2.313,2.844 0.646,0.219 10 false CANL*b 2.854,1.427 3.146,1.594 0.292,0.167 10 false I93 2.177,2.01 2.313,2.198 0.135,0.188 10 false B 2.208,2.26 2.385,2.448 0.177,0.188 10 false W
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector


Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C17
1.5,0.698 1.938,1 0.438,0.302 2.063,1.865 2.219,1.333 2.219,1.333 2.417,1.333 false 2.073,2.563 2.229,2.979 2.229,2.979 2.406,2.979 false 2.521,2.354 2.948,2.354 false 0.104,0.135 0.948,0.469 0.844,0.333 10 *1 1.625,0.76 1.938,0.938 0.313,0.177 10 I39 2.458,1.25 2.865,1.427 0.406,0.177 10 CANH 2.448,2.906 2.833,3.083 0.385,0.177 10 CANL 2.99,2.26 3.323,2.427 0.333,0.167 10 BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).


b.

Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C210421C18
1.51,0.698 1.948,1 0.438,0.302 2.073,1.823 2.208,1.333 2.208,1.333 2.375,1.333 false 2.083,2.531 2.271,2.99 2.271,2.99 2.396,2.99 false 2.51,2.323 2.938,2.323 false 0.083,0.031 0.927,0.365 0.844,0.333 10 *1 1.625,0.76 1.938,0.938 0.313,0.177 10 I39 2.438,1.271 2.844,1.448 0.406,0.177 10 CANH 2.438,2.906 2.823,3.083 0.385,0.177 10 CANL 2.958,2.24 3.292,2.406 0.333,0.167 10 BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR