There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3. | ·
Short to ground in CAN main bus line ·
Short to ground in CAN branch line ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Brake actuator assembly ·
Steering sensor ·
Network gateway ECU*1 ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Smart key ECU assembly (certification ECU)*2 ·
Navigation ECU sub-assembly*3 ·
Navigation receiver assembly*6 ·
Radio and display receiver assembly*4 ·
AFS ECU*5 ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector |
*1: w/ Blind spot monitor system
*2: w/ Smart entry and start system
*3: for Navigation Receiver Type with HDD
*4: for Radio and display type
*5: w/ Automatic high beam system
*6: for Navigation Receiver Type without HDD
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
After the repair, perform the CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to DLC3 |
Disconnect the I96 DLC3 branch line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I96 DLC3 branch line connector to the CAN No. 2 junction connector.
Disconnect the connectors from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.
Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
| *1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.
| *A | w/ Automatic High Beam System | *B | w/ Smart Entry and Start System |
| *C | for Navigation Receiver Type with HDD | *D | for Radio and Display Type |
| *E | w/ Blind Spot Monitor System | *F | for Navigation Receiver Type without HDD |
| *1 | AFS ECU | *2 | Steering Sensor |
| *3 | Brake Actuator Assembly | *4 | Smart Key ECU Assembly (Certification ECU) |
| *5 | DLC3 | *6 | Combination Meter Assembly |
| *7 | Navigation ECU Sub-assembly | *8 | Radio and Display Receiver Assembly |
| *9 | ECM | *10 | Power Steering ECU Assembly |
| *11 | Airbag Sensor Assembly | *12 | Air Conditioning Amplifier Assembly |
| *13 | Main Body ECU (Multiplex Network Body ECU) | *14 | Network Gateway ECU |
| *15 | CAN No. 2 Junction Connector | *16 | CAN No. 1 Junction Connector |
| *17 | Navigation Receiver Assembly | - | - |
| *a | Component without harness connected
(CAN No. 2 Junction Connector) |
- | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Combination meter assembly | I94 | R | W |
| DLC3 | I96 | G | W |
| Smart key ECU assembly (certification ECU)*1 | I106 | L | W |
| Brake actuator assembly | I105 | Y | W |
| Steering sensor | I97 | V | W |
| AFS ECU*2 | I112 | BE | W |
*1: w/ Smart Entry and Start System
*2: w/ Automatic High Beam System
| *a | Component without harness connected
(CAN No. 1 Junction Connector) |
- | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| Network gateway ECU*3 | I161 | BE | W |
| Main body ECU (multiplex network body ECU) | I95 | P | W |
| Air conditioning amplifier assembly | I102 | V | W |
| Airbag sensor assembly | I103 | Y | W |
| Power steering ECU assembly | I100 | L | W |
| ECM | I104 | G | W |
·
Navigation ECU sub-assembly*1 ·
Navigation receiver assembly*4 ·
Radio and display receiver assembly*2 |
I107 | R | W |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |
*1: for Navigation Receiver Type with HDD
*2: for Radio and Display Type
*3: w/ Blind Spot Monitor System
*4: for Navigation Receiver Type without HDD
Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus lines.
| Symptom | Proceed to |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) | A |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or higher ) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.) | B |
When there is a short to GND in one or more of the bus lines that connect to an ECU (or sensor):
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or higher ) to confirm that there is a short to GND in the one bus line only.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
A
B
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I101 CAN main bus line connector to the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or higher when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
| Result |
|---|
| OK |
| NG |
OK
NG