Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Speaker Circuit  


DESCRIPTION

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E226481E66
5.396,7.49 7.104,7.906 1.708,0.417 10 false Radio and Display Receiver Assembly 3.021,1.333 4.281,2.104 1.26,0.771 10 false Front No. 2 Speaker Assembly RH 5.552,0.771 5.833,1.042 0.281,0.271 10 false 1 4.542,0.844 4.792,1.063 0.25,0.219 10 false 4 4.542,1.719 5.042,2 0.5,0.281 10 false 2 2.313,0.844 2.604,1.125 0.292,0.281 10 false 3 2.313,1.708 2.594,2.156 0.281,0.448 10 false 1 2.49,0.844 2.813,1.073 0.323,0.229 10 false + 2.5,1.688 2.708,1.927 0.208,0.24 10 false - 4.073,0.854 4.667,1.083 0.594,0.229 10 false TWR+ 4.073,1.719 4.625,1.979 0.552,0.26 10 false TWR- 5.448,0.948 5.813,1.26 0.365,0.313 10 false I152 3.021,1.156 3.281,1.313 0.26,0.156 10 false I83 0.344,1.406 1.625,2.063 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.354,1.26 0.615,1.417 0.26,0.156 10 false J5 3.021,3.313 4.313,4.021 1.292,0.708 10 false Front No. 2 Speaker Assembly LH 4.542,2.813 5,3 0.458,0.188 10 false 4 4.531,3.688 5.073,4.042 0.542,0.354 10 false 2 2.323,2.813 2.615,3.094 0.292,0.281 10 false 3 2.313,3.688 2.677,3.958 0.365,0.271 10 false 1 2.469,2.802 2.896,3.073 0.427,0.271 10 false + 2.479,3.667 2.833,3.854 0.354,0.188 10 false - 4.083,2.813 4.792,3.26 0.708,0.448 10 false TWL+ 4.104,3.688 4.708,3.948 0.604,0.26 10 false TWL- 3.031,3.156 3.292,3.313 0.26,0.156 10 false I1 0.344,3.365 1.615,4.052 1.271,0.688 10 false Front No. 1 Speaker Assembly LH 0.354,3.219 0.615,3.375 0.26,0.156 10 false K5 0.74,5.125 1.625,5.813 0.885,0.688 10 false Rear Speaker Assembly RH 0.74,4.979 1.052,5.177 0.313,0.198 10 false O18 0.74,6.677 1.604,7.344 0.865,0.667 10 false Rear Speaker Assembly LH 0.74,6.521 1.156,6.802 0.417,0.281 10 false O21 5.448,1.823 6.042,2.219 0.594,0.396 10 false I152 5.448,2.927 6.083,3.156 0.635,0.229 10 false I152 5.448,3.792 5.979,4.073 0.531,0.281 10 false I152 5.448,4.844 5.885,5.188 0.438,0.344 10 false I153 5.448,5.479 5.958,5.771 0.51,0.292 10 false I153 5.448,6.365 5.927,6.625 0.479,0.26 10 false I153 5.448,6.99 5.917,7.281 0.469,0.292 10 false I153 5.844,0.958 6.323,1.25 0.479,0.292 10 false FR+ 5.844,1.833 6.438,2.104 0.594,0.271 10 false FR- 5.844,2.927 6.292,3.281 0.448,0.354 10 false FL+ 5.844,3.802 6.427,4.135 0.583,0.333 10 false FL- 5.844,4.854 6.354,5.125 0.51,0.271 10 false RR+ 5.844,5.469 6.229,5.76 0.385,0.292 10 false RR- 5.844,6.344 6.219,6.656 0.375,0.313 10 false RL+ 5.844,6.979 6.104,7.135 0.26,0.156 10 false RL- 5.542,6.802 5.938,6.99 0.396,0.188 10 false 6 5.552,6.177 5.854,6.438 0.302,0.26 10 false 2 5.552,5.292 5.958,5.594 0.406,0.302 10 false 3 5.552,4.667 5.917,4.958 0.365,0.292 10 false 1 5.552,3.604 5.823,3.813 0.271,0.208 10 false 6 5.552,2.74 5.927,3.073 0.375,0.333 10 false 2 5.552,1.635 5.875,1.885 0.323,0.25 10 false 5 1.792,1.073 2.448,1.323 0.656,0.25 10 false 1 1.792,1.708 2.177,1.865 0.385,0.156 10 false 2 1.792,3.042 2.208,3.323 0.417,0.281 10 false 1 1.792,3.677 2.156,3.948 0.365,0.271 10 false 2 1.792,4.854 2.094,5.188 0.302,0.333 10 false 1 1.792,5.5 2.115,5.729 0.323,0.229 10 false 2 1.792,6.365 2.073,6.594 0.281,0.229 10 false 1 1.792,7.01 2.188,7.26 0.396,0.25 10 false 2

PROCEDURE

1.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly A
Rear speaker assembly B


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the I152 radio and display receiver assembly connector.


b.

Disconnect the J5 and K5 front No. 1 speaker assembly connectors.


c.

Disconnect the I83 and I1 front No. 2 speaker assembly connectors.


d.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-1 (FR+) - I83-4 (TWR+) Always Below 1 Ω
I152-5 (FR-) - I83-2 (TWR-) Always Below 1 Ω
I152-2 (FL+) - I1-4 (TWL+) Always Below 1 Ω
I152-6 (FL-) - I1-2 (TWL-) Always Below 1 Ω



e.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - I83-3 (+) Always Below 1 Ω
J5-2 - I83-1 (-) Always Below 1 Ω
K5-1 - I1-3 (+) Always Below 1 Ω
K5-2 - I1-1 (-) Always Below 1 Ω



f.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-1 (FR+) - Body ground Always 10 kΩ or higher
I152-5 (FR-) - Body ground Always 10 kΩ or higher
I152-2 (FL+) - Body ground Always 10 kΩ or higher
I152-6 (FL-) - Body ground Always 10 kΩ or higher



g.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-3 (+) - Body ground Always 10 kΩ or higher
I83-1 (-) - Body ground Always 10 kΩ or higher
I1-3 (+) - Body ground Always 10 kΩ or higher
I1-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.
E226097C11
1.396,1.813 1.042,2.302 false 1.677,1.823 1.542,2.302 false 2.24,1.813 2.604,2.333 false 1.99,1.813 2.125,2.302 false 0.094,0.083 0.25,0.229 0.156,0.146 10 *a 1.5,2.313 1.656,2.458 0.156,0.146 10 + 0.656,2.313 1.26,2.542 0.604,0.229 10 TWR+*A 0.646,2.51 1.24,2.74 0.594,0.229 10 TWL+*B 1.917,2.333 2.49,2.479 0.573,0.146 10 TWR-*A 1.917,2.531 2.521,2.719 0.604,0.188 10 TWL-*B 2.646,2.313 2.76,2.458 0.115,0.146 10 -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
3 (+) - 4 (TWR+) Always Below 1 Ω
1 (-) - 2 (TWR-) Always Below 1 Ω
4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
3 (+) - 4 (TWL+) Always Below 1 Ω
1 (-) - 2 (TWL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both the LH and RH side.




Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the I153 radio and display receiver assembly connector.


b.

Disconnect the O18 and O21 rear speaker assembly connectors.


c.

Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I153-1 (RR+) - O18-1 Always Below 1 Ω
I153-3 (RR-) - O18-2 Always Below 1 Ω
I153-2 (RL+) - O21-1 Always Below 1 Ω
I153-6 (RL-) - O21-2 Always Below 1 Ω



d.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I153-1 (RR+) - Body ground Always 10 kΩ or higher
I153-3 (RR-) - Body ground Always 10 kΩ or higher
I153-2 (RL+) - Body ground Always 10 kΩ or higher
I153-6 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR SPEAKER ASSEMBLY

b.
E219303C30
0.177,0.146 0.573,0.469 0.396,0.323 10 *a
*a Component without harness connected
(Rear Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω



Result:
Proceed to
OK
NG



OK

NG