Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE SONAR MAIN SWITCH › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074091 CLEARANCE SONAR MAIN SWITCH G

PARK ASSIST / MONITORING  CLEARANCE SONAR MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 84490A 1.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

a.
E307481C01
1.198,1.854 1.5,1.854 1.5,1.854 1.5,1.292 false 2.271,1.865 1.969,1.865 1.969,1.865 1.969,1.292 false 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.99,1.76 1.323,2 0.333,0.24 10 false IG 2.333,1.781 2.792,2.031 0.458,0.25 10 false ECU
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (IG) - 3 (ECU) Clearance sonar main switch on Below 1 Ω
6 (IG) - 3 (ECU) Clearance sonar main switch off 10 kΩ or higher


If the result is not as specified, replace the back sonar or clearance sonar switch assembly.


b.

Check that the switch illuminates.

i.
E307481C02
1.354,1.854 1.656,1.854 1.656,1.854 1.656,1.292 false 2.125,1.865 1.823,1.865 1.823,1.865 1.823,1.292 false 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 1.042,1.771 1.375,2.01 0.333,0.24 10 false ILL+ 2.198,1.771 2.656,2.021 0.458,0.25 10 false ILL-
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Apply battery voltage to the back sonar or clearance sonar switch assembly and check that the switch illuminates.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 4 (ILL-)
Illuminates


If the result is not as specified, replace the back sonar or clearance sonar switch assembly.



c.

Check switch indicator operation.

i.
E307481C03
0.979,1.854 1.281,1.854 1.281,1.854 1.281,1.292 false 1.823,1.865 1.521,1.865 1.521,1.865 1.521,1.292 false 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.844,1.792 1.177,2.031 0.333,0.24 10 false E 1.885,1.792 2.344,2.042 0.458,0.25 10 false IG
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Apply battery voltage to the back sonar or clearance sonar switch assembly and check that the switch indicator illuminates.

OK:
Tester Connection Switch Condition Specified Condition
Battery positive (+) → Terminal 6 (IG)
Battery negative (-) → Terminal 7 (E)
Clearance sonar main switch on Indicator Illuminates


If the result is not as specified, replace the back sonar or clearance sonar switch assembly.