After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
Turn the ignition switch off before inspecting CAN bus lines for a ground short.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
CAN NO. 1 JUNCTION CONNECTOR (for LHD)
Check the CAN No. 1 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN No. 1 Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
| *c | to Steering Sensor
(w/ VSC) (for V Bus) |
*d | to Airbag Sensor Assembly
(for V Bus) |
| *e | to DLC3
(for V Bus) |
*f | to Power Steering ECU Assembly
(for V Bus) |
| *g | to Combination Meter Assembly
(for V Bus) |
*h | to CAN No. 2 Junction Connector
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I95-1 (CANH) | P | Main body ECU (multiplex network body ECU)
(for V bus) |
| I95-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor*
(for V bus) |
| I97-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly
(for V bus) |
| I103-2 (CANL) | W | |
| I96-1 (CANH) | L | DLC3
(for V bus) |
| I96-2 (CANL) | W | |
| I100-1 (CANH) | G | Power steering ECU assembly
(for V bus) |
| I100-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly
(for V bus) |
| I94-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN No. 2 junction connector
(for V bus) |
| I93-2 (CANL) | W |
*: w/ VSC
CAN NO. 1 JUNCTION CONNECTOR (for RHD)
Check the CAN No. 1 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN No. 1 Junction Connector) |
*b | to Network Gateway ECU
(w/ Pre-crash Safety System) (for V Bus) |
| *c | to Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
*d | to Air Conditioning Amplifier Assembly
(for V Bus) |
| *e | to Airbag Sensor Assembly
(for V Bus) |
*f | to Power Steering ECU Assembly
(for V Bus) |
| *g | to ECM
(for V Bus) |
*h | ·
to Navigation Receiver Assembly (for Navigation Receiver Type) ·
to Radio and Display Receiver Assembly (for Radio and Display Type) (for V Bus) |
| *i | to CAN No. 2 Junction Connector
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I161-1 (CANH) | BE | Network gateway ECU*1
(for V bus) |
| I161-2 (CANL) | W | |
| I95-1 (CANH) | P | Main body ECU (multiplex network body ECU)
(for V bus) |
| I95-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly
(for V bus) |
| I102-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly
(for V bus) |
| I103-2 (CANL) | W | |
| I100-1 (CANH) | L | Power steering ECU assembly
(for V bus) |
| I100-2 (CANL) | W | |
| I104-1 (CANH) | G | ECM
(for V bus) |
| I104-2 (CANL) | W | |
| I107-1 (CANH) | R | ·
Navigation receiver assembly*2 ·
Radio and display receiver assembly*3 (for V bus) |
| I107-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN No. 2 junction connector
(for V bus) |
| I93-2 (CANL) | W |
*1: w/ Pre-crash Safety System
*2: for Navigation Receiver Type
*3: for Radio and Display Type
CAN NO. 2 JUNCTION CONNECTOR (for LHD)
Check the CAN No. 2 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN No. 2 Junction Connector) |
*b | to Brake Actuator Assembly
(for V Bus) |
| *c | ·
to Navigation Receiver Assembly (for Navigation Receiver Type) ·
to Radio and Display Receiver Assembly (for Radio and Display Type) (for V Bus) |
*d | to Network Gateway ECU
(w/ Parking Assist Monitor System) (for V Bus) |
| *e | to Smart Key ECU Assembly (Certification ECU)
(w/ Smart Entry and Start System) (for V Bus) |
*f | to ECM
(for V Bus) |
| *g | to Air Conditioning Amplifier Assembly
(for V Bus) |
*h | to CAN No. 1 Junction Connector
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I105-1 (CANH) | Y | Brake actuator assembly
(for V bus) |
| I105-2 (CANL) | W | |
| I107-1 (CANH) | R | ·
Navigation receiver assembly*2 ·
Radio and display receiver assembly*3 (for V bus) |
| I107-2 (CANL) | W | |
| I161-1 (CANH) | G | Network gateway ECU*4
(for V bus) |
| I161-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (certification ECU)*1
(for V bus) |
| I106-2 (CANL) | W | |
| I104-1 (CANH) | P | ECM
(for V bus) |
| I104-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly
(for V bus) |
| I102-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN No. 1 junction connector
(for V bus) |
| I101-2 (CANL) | W |
*1: w/ Smart Entry and Start System
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Parking Assist Monitor System
CAN NO. 2 JUNCTION CONNECTOR (for RHD)
Check the CAN No. 2 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN No. 2 Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System) (for V Bus) |
| *c | to Steering Sensor
(for V Bus) |
*d | to Brake Actuator Assembly
(for V Bus) |
| *e | to Smart Key ECU Assembly (Certification ECU)
(w/ Smart Entry and Start System) (for V Bus) |
*f | to DLC3
(for V Bus) |
| *g | to Combination Meter Assembly
(for V Bus) |
*h | to CAN No. 1 Junction Connector
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I177-1 (CANH) | P | Clearance warning ECU assembly*2
(for V bus) |
| I177-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor
(for V bus) |
| I97-2 (CANL) | W | |
| I105-1 (CANH) | Y | Brake actuator assembly
(for V bus) |
| I105-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (certification ECU)*1
(for V bus) |
| I106-2 (CANL) | W | |
| I96-1 (CANH) | G | DLC3
(for V bus) |
| I96-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly
(for V bus) |
| I94-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN No. 1 junction connector
(for V bus) |
| I101-2 (CANL) | W |
*1: w/ Smart Entry and Start System
*2: w/ Toyota Parking Assist-sensor System
CAN NO. 3 JUNCTION CONNECTOR (w/ Seat Position Memory System)
Check the CAN No. 3 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN No. 3 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I162-1 (CANH) | R | Main body ECU (multiplex network body ECU) |
| I162-2 (CANL) | GR | |
| I163-1 (CANH) | G | Outer mirror control ECU assembly (for front passenger side) |
| I163-2 (CANL) | GR | |
| I166-1 (CANH) | Y | CAN No. 4 junction connector |
| I166-2 (CANL) | R |
CAN NO. 4 JUNCTION CONNECTOR (w/ Seat Position Memory System)
Check the CAN No. 4 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN No. 4 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 4 Junction Connector) |
Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I168-1 (GND) | W-B | Body ground |
| I167-1 (CANH) | Y | CAN No. 3 junction connector |
| I167-2 (CANL) | R | |
| I165-1 (CANH) | BE | Position control ECU and switch assembly (for driver side) |
| I165-2 (CANL) | GR | |
| I164-1 (CANH) | P | Outer mirror control ECU assembly (for driver side) |
| I164-2 (CANL) | GR |
CAN NO. 5 JUNCTION CONNECTOR (w/ Parking Assist Monitor System or Pre-crash Safety System)
Check the CAN No. 5 junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector
(for Sub Bus 2) |
| *c | to Blind Spot Monitor Sensor RH
(w/ Pre-crash Safety System) (for Sub Bus 2) |
| *d | to CAN No. 9 Junction Connector
(for Sub Bus 2) |
Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| O31-8 (CANH) | G | CAN No. 6 junction connector
(for Sub bus 2) |
| O31-19 (CANL) | B | |
| O31-9 (CANH) | R | Blind spot monitor sensor RH*
(for Sub bus 2) |
| O31-20 (CANL) | B | |
| O31-11 (CANH) | V | CAN No. 9 junction connector
(for Sub bus 2) |
| O31-22 (CANL) | B |
*: w/ Pre-crash Safety System
CAN NO. 6 JUNCTION CONNECTOR (w/ Parking Assist Monitor System or Pre-crash Safety System)
Check the CAN No. 6 junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector
(for Sub Bus 2) |
| *c | to Rear Television Camera Assembly
(for Sub Bus 2) |
| *d | to CAN No. 5 Junction Connector
(for Sub Bus 2) |
Check the connection diagram of the components which are connected to the CAN No. 6 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| T17-1 (CANH) | L | CAN No. 7 junction connector
(for Sub bus 2) |
| T17-12 (CANL) | B | |
| T17-2 (CANH) | V | Rear television camera assembly
(for Sub bus 2) |
| T17-13 (CANL) | P | |
| T17-3 (CANH) | G | CAN No. 5 junction connector
(for Sub bus 2) |
| T17-14 (CANL) | B |
CAN NO. 7 JUNCTION CONNECTOR (w/ Parking Assist Monitor System or Pre-crash Safety System)
Check the CAN No. 7 junction connector.
Connection diagram
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector
(for Sub Bus 2) |
Check the connection diagram of the components which are connected to the CAN No. 7 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| T18-3 (CANH) | L | CAN No. 6 junction connector
(for Sub bus 2) |
| T18-2 (CANL) | B |
CAN NO. 8 JUNCTION CONNECTOR (w/ Pre-crash Safety System)
Check the CAN No. 8 junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to CAN No. 8 Junction Connector) |
*b | to Lane Departure Warning Camera
(for Sub Bus 2) |
| *c | to CAN No. 9 Junction Connector
(for Sub Bus 2) |
*d | to Network Gateway ECU
(for Sub Bus 2) |
Check the connection diagram of the components which are connected to the CAN No. 8 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| S15-1 (CANH) | V | Lane departure warning camera
(for Sub bus 2) |
| S15-7 (CANL) | LG | |
| S15-2 (CANH) | R | CAN No. 9 junction connector
(for Sub bus 2) |
| S15-8 (CANL) | LG | |
| S15-3 (CANH) | B | Network gateway ECU
(for Sub bus 2) |
| S15-9 (CANL) | LG |
CAN NO. 9 JUNCTION CONNECTOR (for LHD with Parking Assist Monitor System)
Check the CAN No. 9 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN No. 9 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 9 Junction Connector) |
Check the connection diagram of the components which are connected to the CAN No. 9 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I178-1 (CANH) | B | Network gateway ECU
(for Sub bus 2) |
| I178-2 (CANL) | LG | |
| I179-1 (CANH) | V | CAN No. 5 junction connector
(for Sub bus 2) |
| I179-2 (CANL) | LG |
CAN NO. 9 JUNCTION CONNECTOR (for RHD with Pre-crash Safety System)
Check the CAN No. 9 junction connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN No. 9 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 9 Junction Connector) |
Check the connection diagram of the components which are connected to the CAN No. 9 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I179-1 (CANH) | V | CAN No. 5 junction connector
(for Sub bus 2) |
| I179-2 (CANL) | LG | |
| I192-1 (CANH) | L | Driving support ECU assembly
(for Sub bus 2) |
| I192-2 (CANL) | LG | |
| I193-1 (CANH) | R | CAN No. 8 junction connector
(for Sub bus 2) |
| I193-2 (CANL) | LG |
DLC3
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | L - W*1
G - W*2 |
HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I39-6 (CANH) - I39-4 (CG) | L - W-B*1
G - W-B*2 |
HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-6 (CANH) - I39-16 (BAT) | L - R*1
G - R*2 |
HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
*1: for LHD
*2: for RHD
ECM
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A25-13 (CANH) - A25-26 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A25-13 (CANH) - E26-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-26 (CANL) - E26-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-13 (CANH) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A25-26 (CANL) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY (w/o Multi-information Display)
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I18-16 (CANH) - I18-15 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I18-16 (CANH) - I18-7 (ES) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-15 (CANL) - I18-7 (ES) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-16 (CANH) - I18-1 (B) | R - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I18-15 (CANL) - I18-1 (B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY (w/ Multi-information Display)
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I18-17 (CANH) - I18-16 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I18-17 (CANH) - I18-20 (ES) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-16 (CANL) - I18-20 (ES) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-17 (CANH) - I18-1 (B) | R - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I18-16 (CANL) - I18-1 (B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
| *1 | Main Body ECU (Multiplex Network Body ECU)) | *2 | 2 connectors |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| *A | for LHD | *B | for RHD |
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | 3 connectors |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connectors.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I13-14 (CANH) - I13-13 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I13-14 (CANH) - I39-4 (CG) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-13 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-14 (CANH) - I39-16 (BAT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I13-13 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I12-9 (CANP) - I12-10 (CANN) | R - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I12-9 (CANP) - I39-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-10 (CANN) - I39-4 (CG) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-9 (CANP) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I12-10 (CANN) - I39-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-26 (CANH) - A49-14 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A49-26 (CANH) - A49-38 (GND1) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-14 (CANL) - A49-38 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-26 (CANH) - A49-25 (+BS) | GR - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A49-14 (CANL) - A49-25 (+BS) | W - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR (w/ VSC)
Disconnect the cable from the negative (-) battery terminal.
Disconnect the steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I29-3 (CANH) - I29-2 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I29-3 (CANH) - I29-1 (ESS) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-2 (CANL) - I29-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-3 (CANH) - I29-5 (BAT) | V - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I29-2 (CANL) - I29-5 (BAT) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
| *a | Component without harness connected
(Power Steering ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power steering ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| j1-4 (CANH) - j1-8 (CANL) | Y - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| j1-4 (CANH) - j2-2 (PGND) | Y - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| j1-8 (CANL) - j2-2 (PGND) | SB - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| j1-4 (CANH) - j2-1 (PIG) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| j1-8 (CANL) - j2-1 (PIG) | SB - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I47-13 (CANH) - I47-22 (CANL) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I47-13 (CANH) - I47-25 (E1) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I47-22 (CANL) - I47-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I47-13 (CANH) - I39-16 (BAT) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I47-22 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) (w/ Smart Entry and Start System)
| *a | Component without harness connected
(Smart Key ECU Assembly (Certification ECU)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the smart key ECU assembly (certification ECU) connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I78-14 (CANH) - I78-15 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I78-14 (CANH) - A43-11 (E) | L - W | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I78-15 (CANL) - A43-11 (E) | W - W | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I78-14 (CANH) - A43-2 (+B) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I78-15 (CANL) - A43-2 (+B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I155-9 (CANH) - I155-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I155-9 (CANH) - I152-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I155-10 (CANL) - I152-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I155-9 (CANH) - I152-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I155-10 (CANL) - I152-4 (+B1) | W - L-Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)
| *a | Component without harness connected
(Navigation Receiver Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the navigation receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I67-9 (CANH) - I67-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I67-9 (CANH) - I64-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I67-10 (CANL) - I64-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I67-9 (CANH) - I64-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I67-10 (CANL) - I64-4 (+B1) | W - L-Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I77-11 (CANH) - I77-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I77-11 (CANH) - I77-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-12 (CANL) - I77-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-11 (CANH) - I77-21 (B) | V - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I77-12 (CANL) - I77-21 (B) | W - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I77-11 (CANH) - I77-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I77-11 (CANH) - I77-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-12 (CANL) - I77-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-11 (CANH) - I77-21 (B) | V - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I77-12 (CANL) - I77-21 (B) | W - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the outer mirror control ECU assembly connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J13-9 (CANP) - J13-8 (CANN) | P - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| J13-9 (CANP) - J13-7 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J13-8 (CANN) - J13-7 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J13-9 (CANP) - J13-6 (CPUB) | P - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J13-8 (CANN) - J13-6 (CPUB) | GR - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the outer mirror control ECU assembly connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K12-9 (CANP) - K12-8 (CANN) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| K12-9 (CANP) - K12-7 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K12-8 (CANN) - K12-7 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K12-9 (CANP) - K12-6 (CPUB) | G - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K12-8 (CANN) - K12-6 (CPUB) | GR - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the position control ECU and switch assembly (for driver side) connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| d12-8 (CANP) - d12-7 (CANN) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| d12-8 (CANP) - d11-2 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| d12-7 (CANN) - d11-2 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| d12-8 (CANP) - d11-7 (+B) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| d12-7 (CANN) - d11-7 (+B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
NETWORK GATEWAY ECU (w/ Parking Assist Monitor System or Pre-crash Safety System)
| *a | Component without harness connected
(Network Gateway ECU) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1:LHD *2:RHD |
||||
| I160-16 (CA1H) - I160-15 (CA1L) | G*1, BE*2 - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I160-16 (CA1H) - I160-4 (GND) | G*1, BE*2 - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I160-15 (CA1L) - I160-4 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I160-16 (CA1H) - I160-2 (BATT) | G*1, BE*2 - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I160-15 (CA1L) - I160-2 (BATT) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | B - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I160-13 (CA2H) - I160-4 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I160-12 (CA2L) - I160-4 (GND) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I160-13 (CA2H) - I160-2 (BATT) | B - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I160-12 (CA2L) - I160-2 (BATT) | LG - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Pre-crash Safety System)
| *a | Component without harness connected
(Rear Television Camera Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| T22-4 (CANH) - T22-1 (CANL) | V - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| T22-4 (CANH) - I39-4 (CG) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T22-1 (CANL) - I39-4 (CG) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T22-4 (CANH) - I39-16 (BAT) | V - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T22-1 (CANL) - I39-16 (BAT) | P - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)
Disconnect the cable from the negative (-) battery terminal.
Disconnect the clearance warning ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I82-17 (R1) - I82-18 (R2) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I82-17 (R1) - I82-30 (E) | P - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I82-18 (R2) - I82-30 (E) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I82-17 (R1) - I39-16 (BAT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I82-18 (R2) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR RH (w/ Pre-crash Safety System)
| *a | Component without harness connected
(Blind Spot Monitor Sensor RH) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the blind spot monitor sensor RH connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| O32-2 (CA1P) - O32-7 (CA1N) | R - B | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| O32-2 (CA1P) - O32-10 (BRGD) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O32-7 (CA1N) - O32-10 (BRGD) | B - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O32-2 (CA1P) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O32-7 (CA1N) - I39-16 (BAT) | B - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
LANE DEPARTURE WARNING CAMERA (w/ Pre-crash Safety System)
| *a | Component without harness connected
(Lane Departure Warning Camera) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the lane departure warning camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Lane Departure Warning Camera) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S14-6 (CA1P) - S14-12 (CA1N) | V - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S14-6 (CA1P) - S14-11 (GND) | V - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S14-12 (CA1N) - S14-11 (GND) | LG - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S14-6 (CA1P) - I39-16 (BAT) | V - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S14-12 (CA1N) - I39-16 (BAT) | LG - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)
| *a | Component without harness connected
(Driving Support ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Driving Support ECU Assembly) |
Disconnect the driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I191-39 (CA2H) - I191-17 (CA2L) | L - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I191-39 (CA2H) - I191-25 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I191-17 (CA2L) - I191-25 (GND) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I191-39 (CA2H) - I191-30 (B) | L - V | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I191-17 (CA2L) - I191-30 (B) | LG - V | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I191-40 (CA1P) - I191-18 (CA1N) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I191-40 (CA1P) - I191-25 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I191-18 (CA1N) - I191-25 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I191-40 (CA1P) - I191-30 (B) | LG - V | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I191-18 (CA1N) - I191-30 (B) | W - V | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A79-3 (CA1P) - A79-2 (CA1N) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A79-3 (CA1P) - A79-1 (SGND) | B - L | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A79-2 (CA1N) - A79-1 (SGND) | W - L | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A79-3 (CA1P) - I39-16 (BAT) | B - R | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A79-2 (CA1N) - I39-16 (BAT) | W - R | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |