Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2015.04
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074131 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


a.

Disconnect the I19 transponder key ECU assembly connector.

B255101N03
3.459,0.219 3.836,0.437 0.377,0.218 3.56,0.254 3.829,0.417 0.27,0.163 10 I19


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
I19-1 (+B) - I19-5 (GND) W - BR Battery Always 11 to 14 V
I19-2 (IG) - I19-5 (GND) R - BR Ignition switch signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I19-3 (KSW) - I19-5 (GND) G - BR Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher
Key in ignition key cylinder Below 1 Ω
I19-5 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I19 transponder key ECU assembly connector.


d.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I19-8 (IND) - I19-5 (GND) L - BR Security indicator signal No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to on (ACC) or off (engine immobiliser system set) Pulse generation
Key in ignition key cylinder (engine immobiliser system unset) Below 1 V
I19-9 (D) - I19-5 (GND) GR - BR DLC3 communication Without communication Below 1 V
During communication Pulse generation
I19-4 (ANT1) - I19-5 (GND) LG - BR Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
I19-15 (ANT2) - I19-5 (GND) SB - BR Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
I19-12 (EFII) - I19-5 (GND) R - BR ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
I19-13 (EFIO) - I19-5 (GND) G - BR ECM output signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation
(See waveform 4)

If the result is not as specified, the transponder key ECU assembly may have a malfunction.


e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B329909N04
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Measurement Condition
Item Content
Tester Connection I19-4 (ANT1) - I19-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N03
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Measurement Condition
Item Content
Tester Connection I19-15 (ANT2) - I19-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B337754C01
0.802,1.25 1.26,1.448 0.458,0.198 10 GND 2.719,1.333 3.177,1.531 0.458,0.198 10 *a 2.906,1.333 3.365,1.531 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection I19-12 (EFII) - I19-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starteroperation and initial combustion, orwithin 3 seconds of ignition switchfirst being turned to ON after cabledisconnected and reconnected tonegative (-) battery terminal


iv.

Waveform 4 (Reference)

B337755C01
0.813,1.26 1.271,1.458 0.458,0.198 10 GND 3.115,1.365 3.573,1.563 0.458,0.198 10 *a 3.302,1.365 3.76,1.563 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection I19-13 (EFIO) - I19-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM


A247842E35
2.529,0.494 2.926,0.732 0.397,0.238 2.602,0.543 2.901,0.702 0.299,0.159 10 E26 5.905,0.493 6.302,0.732 0.397,0.238 5.979,0.541 6.277,0.7 0.299,0.159 10 A25

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
E26-16 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
A25-1 (BATT) - E26-16 (E1) GR - BR +B power supply Always 11 to 14 V
A25-3 (+B2) - E26-16 (E1) LG - BR +B power supply Ignition switch ON 11 to 14 V
A25-2 (+B) - E26-16 (E1) P - BR +B power supply Ignition switch ON 11 to 14 V
A25-29 (IMO) - E26-16 (E1) G - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V
A25-29 (IMO) - E26-16 (E1) G - BR Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. Pulse generation
(See waveform 1)
A25-28 (IMI) - E26-16 (E1) Y - BR Transponder key ECU assembly communication output Ignition switch off Below 1 V
A25-28 (IMI) - E26-16 (E1) Y - BR Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. Pulse generation
(See waveform 2)

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B337754C04
0.802,1.25 1.26,1.448 0.458,0.198 10 false GND 2.719,1.333 3.177,1.531 0.458,0.198 10 false *a 2.906,1.333 3.365,1.531 0.458,0.198 10 false *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A25-29 (IMO) - E26-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.


ii.

Waveform 2 (Reference)

B337755C02
0.813,1.26 1.271,1.458 0.458,0.198 10 GND 3.115,1.365 3.573,1.563 0.458,0.198 10 *a 3.302,1.365 3.76,1.563 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A25-28 (IMI) - E26-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.