Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074150 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any defects are found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

C291747C10
2.542,0.344 2.854,0.552 0.313,0.208 4.917,0.823 5.229,1.031 0.313,0.208 6.604,0.854 6.917,1.063 0.313,0.208 1.979,1.635 2.292,1.844 0.313,0.208 0.208,1.885 0.521,2.094 0.313,0.208 2.635,0.875 2.375,0.635 false 2.76,0.875 2.99,0.635 false 5.573,0.885 5.135,0.375 false 5.781,0.885 5.875,0.375 false 5.875,0.885 6.302,0.375 false 5.979,0.885 6.635,0.365 false 5.573,1.052 5.083,1.375 false 5.677,1.052 5.448,1.385 false 5.781,1.052 5.802,1.385 false 5.875,1.052 6.177,1.385 false 6.26,1.063 6.552,1.396 6.552,1.396 5.979,1.042 false 6.365,1.063 6.615,1.229 false 1.5,1.635 1.302,1.208 false 1.5,1.729 0.948,1.208 false 1.5,1.823 0.573,1.208 false 0.906,1.74 0.479,1.385 false 0.896,1.906 0.448,1.635 false 1.5,1.927 0.885,2.5 false 1.5,2.031 1.271,2.49 false 1.646,2.031 1.979,2.333 false 1.646,1.833 1.969,1.979 false 1.542,1.542 1.698,1.198 false 1.656,1.635 1.979,1.333 false 1.656,1.74 1.969,1.531 false 1.51,2.125 1.594,2.49 false 1.625,2.125 1.958,2.5 false 5.469,1.042 5.229,1.156 false 5.458,0.917 5.229,0.698 false 1.646,1.542 1.979,1.135 false 6.375,0.917 6.615,0.677 false 1.635,1.927 1.969,2.156 false 5.677,0.885 5.49,0.385 false 0.083,0.052 0.438,0.333 0.354,0.281 10 false *a 2.635,0.365 2.99,0.646 0.354,0.281 10 false z4 2.198,0.552 2.552,0.833 0.354,0.281 10 false D- 3.021,0.552 3.375,0.833 0.354,0.281 10 false D+ 5,0.854 5.354,1.135 0.354,0.281 10 false z3 6.542,0.219 6.865,0.5 0.323,0.281 10 false HO 6.146,0.219 6.5,0.5 0.354,0.281 10 false +DP 5.698,0.219 6.177,0.51 0.479,0.292 10 false +DP2 5,0.219 5.354,0.5 0.354,0.281 10 false IL+2 4.938,1.396 5.292,1.677 0.354,0.281 10 false AU1 5.292,1.396 5.646,1.677 0.354,0.281 10 false AU2 5.677,1.396 6.031,1.677 0.354,0.281 10 false AU3 6.042,1.396 6.396,1.677 0.354,0.281 10 false EAU 6.417,1.396 6.771,1.677 0.354,0.281 10 false ECC 6.646,1.156 7,1.438 0.354,0.281 10 false CCS 6.698,0.875 7.052,1.156 0.354,0.281 10 false z2 2.052,1.667 2.406,1.948 0.354,0.281 10 false I28 0.281,1.906 0.635,2.188 0.354,0.281 10 false I27 0.271,1.302 0.625,1.583 0.354,0.281 10 false D+ 0.271,1.552 0.625,1.833 0.354,0.281 10 false D- 0.448,1.042 0.802,1.323 0.354,0.281 10 false AU3 0.792,1.042 1.146,1.323 0.354,0.281 10 false EAU 1.156,1.042 1.51,1.323 0.354,0.281 10 false ECC 1.563,1.052 1.917,1.333 0.354,0.281 10 false CCS 2.01,1.25 2.365,1.531 0.354,0.281 10 false HO 2,1.448 2.354,1.729 0.354,0.281 10 false +DP 2,1.906 2.49,2.281 0.49,0.375 10 false +DP2 2.021,2.271 2.375,2.552 0.354,0.281 10 false IL+2 1.125,2.5 1.479,2.781 0.354,0.281 10 false AU1 0.75,2.5 1.104,2.781 0.354,0.281 10 false AU2 1.469,2.5 1.823,2.781 0.354,0.281 10 false SDN 1.833,2.5 2.188,2.781 0.354,0.281 10 false SUP 4.917,1.094 5.271,1.375 0.354,0.281 10 false SDN 4.917,0.615 5.271,0.896 0.354,0.281 10 false SUP 2.01,1.052 2.365,1.333 0.354,0.281 10 false R/N 6.646,0.594 7.01,1.385 0.365,0.792 10 false R/N 2,2.083 2.49,2.458 0.49,0.375 10 false DIST 5.344,0.219 5.823,0.51 0.479,0.292 10 false DIST
*a Component without harness connected
(Spiral Cable Sub-assembly)
- -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-1 (CCS) - z2-3 (CCS) Always 3 Ω or less
I28-2 (ECC) - z2-4 (ECC) Always 3 Ω or less
I28-2 (ECC) - z3-7 (ECC) Always 3 Ω or less
I28-3 (EAU) - z3-8 (EAU) Always 3 Ω or less
I28-4 (AU3) - z3-9 (AU3) Always 3 Ω or less
I28-5 (AU2) - z3-10 (AU2) Always 3 Ω or less
I28-6 (AU1) - z3-11 (AU1) Always 3 Ω or less
I28-7 (SDN) - z3-12 (SDN) Always 3 Ω or less
I28-8 (R/N) - z2-1 (R/N) Always 3 Ω or less
I28-9 (HO) - z3-1 (HO) Always 3 Ω or less
I28-10 (+DP) - z3-2 (+DP) Always 3 Ω or less
I28-11 (+DP2) - z3-3 (+DP2) Always 3 Ω or less
I28-12 (DIST) - z3-4 (DIST) Always 3 Ω or less
I28-13 (IL+2) - z3-5 (IL+2) Always 3 Ω or less
I28-14 (SUP) - z3-6 (SUP) Always 3 Ω or less
I27-1 (D+) - z4-2 (D+) Always Below 1 Ω
I27-2 (D-) - z4-1 (D-) Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-1 (CCS) - z2-3 (CCS) Always 3 Ω or less
I28-2 (ECC) - z2-4 (ECC) Always 3 Ω or less
I28-2 (ECC) - z3-7 (ECC) Always 3 Ω or less
I28-3 (EAU) - z3-8 (EAU) Always 3 Ω or less
I28-4 (AU3) - z3-9 (AU3) Always 3 Ω or less
I28-5 (AU2) - z3-10 (AU2) Always 3 Ω or less
I28-6 (AU1) - z3-11 (AU1) Always 3 Ω or less
I28-7 (SDN) - z3-12 (SDN) Always 3 Ω or less
I28-8 (R/N) - z2-1 (R/N) Always 3 Ω or less
I28-9 (HO) - z3-1 (HO) Always 3 Ω or less
I28-10 (+DP) - z3-2 (+DP) Always 3 Ω or less
I28-11 (+DP2) - z3-3 (+DP2) Always 3 Ω or less
I28-12 (DIST) - z3-4 (DIST) Always 3 Ω or less
I28-13 (IL+2) - z3-5 (IL+2) Always 3 Ω or less
I28-14 (SUP) - z3-6 (SUP) Always 3 Ω or less
I27-1 (D+) - z4-2 (D+) Always Below 1 Ω
I27-2 (D-) - z4-1 (D-) Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-1 (CCS) - z2-3 (CCS) Always 3 Ω or less
I28-2 (ECC) - z2-4 (ECC) Always 3 Ω or less
I28-2 (ECC) - z3-7 (ECC) Always 3 Ω or less
I28-3 (EAU) - z3-8 (EAU) Always 3 Ω or less
I28-4 (AU3) - z3-9 (AU3) Always 3 Ω or less
I28-5 (AU2) - z3-10 (AU2) Always 3 Ω or less
I28-6 (AU1) - z3-11 (AU1) Always 3 Ω or less
I28-7 (SDN) - z3-12 (SDN) Always 3 Ω or less
I28-8 (R/N) - z2-1 (R/N) Always 3 Ω or less
I28-9 (HO) - z3-1 (HO) Always 3 Ω or less
I28-10 (+DP) - z3-2 (+DP) Always 3 Ω or less
I28-11 (+DP2) - z3-3 (+DP2) Always 3 Ω or less
I28-12 (DIST) - z3-4 (DIST) Always 3 Ω or less
I28-13 (IL+2) - z3-5 (IL+2) Always 3 Ω or less
I28-14 (SUP) - z3-6 (SUP) Always 3 Ω or less
I27-1 (D+) - z4-2 (D+) Always Below 1 Ω
I27-2 (D-) - z4-1 (D-) Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.