Moving the shift lever to S enables gear selection. The driver can select the gear optionally by shifting the paddle to "+" or "-".
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Continuously pull to "+" (up-shift) ·
OFF: Release "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Continuously pull to "-" (down-shift) ·
OFF: Release "-" (down-shift) |
- |
| Tester Display |
|---|
| Sports Shift Up SW |
| Sports Shift Down SW |
| Result | Proceed to |
|---|---|
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
A
B
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A25-43 (SFTD) - Body ground | Pull "-" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher | |
| A25-42 (SFTU) - Body ground | Pull "+" continuously
(Up-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the negative (-) terminal cable from the battery.
Wait for at least 90 seconds.
Remove the steering wheel assembly.
Remove the steering column cover.
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Disconnect the spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| l28-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A25-43 (SFTD) - l28-7 (SDN) | Always | Below 1 Ω |
| A25-43 (SFTD) or l28-7 (SDN) - Body ground | Always | 10 kΩ or higher |
| A25-42 (SFTU) - l28-14 (SUP) | Always | Below 1 Ω |
| A25-42 (SFTU) or l28-14 (SUP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the horn button assembly.
Disconnect the steering pad switch connector from the spiral cable sub-assembly.
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Measure the resistance according to the value(s) in the table below when the shift paddle switch is moved to each position.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-6 (SUP) - z3-7 (ECC) | Pull "+" continuously
(Up-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher | |
| z3-12 (SDN) - z3-7 (ECC) | Pull "-" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering pad switch connector from the spiral cable sub-assembly.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
*b | Steering Pad Switch Side |
| *c | Vehicle Side | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-7 (ECC) - l28-2 (ECC) | Always | Below 3 Ω |
| z3-6 (SUP) - l28-14 (SUP) | Always | Below 3 Ω |
| z3-12 (SDN) - l28-7 (SDN) | Always | Below 3 Ω |
| z3-7 (ECC) or l28-2 (ECC) - All other terminals | Always | 10 kΩ or higher |
| z3-6 (SUP) or l28-14 (SUP) - All other terminals | Always | 10 kΩ or higher |
| z3-12 (SDN) or l28-7 (SDN) - All other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift paddle switch LH) |
| *b | Component without harness connected
(Shift paddle switch RH) |
Disconnect the connector from the transmission shift switch LH and RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C-3 (ECC) - C-2 (SFTD) | Pull "-" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher | |
| C-4 (ECC1) - C-2 (SFTD) | Pull "-" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B-3 (SFTU) - B-2 (ECC1) | Pull "+" continuously
(Up-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the transmission shift switch LH and RH connector.
| *a | Front view of wire harness connector
(to Steering Pad Switch Connector) |
Disconnect the No.1 switch wire from steering pad switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A-3 (SFTD) - A17-7 (ECC) | Pull "-" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher | |
| A-2 (SFTU) - A17-7 (ECC) | Pull "+" continuously
(Down-shift) |
Below 1 Ω |
| Release | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG