Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2016.05
RM19V0EQ _58 Vehicle Interior _014612 SEAT BELT _0074172 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the clock assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B448719E03
1.917,0.563 2.531,0.76 0.615,0.198 10 false RLMT 1.917,0.979 2.531,1.177 0.615,0.198 10 false RCMT 1.917,1.427 2.531,1.625 0.615,0.198 10 false RRMT 1.917,2.667 2.531,2.865 0.615,0.198 10 false RLSB 1.906,3.885 2.521,4.083 0.615,0.198 10 false RCSB 1.917,4.417 2.531,4.615 0.615,0.198 10 false RRSB 2.406,0.344 3.115,0.573 0.708,0.229 10 false 9*1, 6*2 2.479,0.563 2.938,0.76 0.458,0.198 10 false I17 2.385,0.781 3.073,1.01 0.688,0.229 10 false 10*1, 2*2 2.406,1.208 3.167,1.406 0.76,0.198 10 false 11*1, 3*2 2.406,2.438 3.073,2.667 0.667,0.229 10 false 3*1, 10*2 2.396,3.635 3.031,3.833 0.635,0.198 10 false 4*1, 5*2 2.385,4.167 2.969,4.365 0.583,0.198 10 false 5*1, 6*2 2.469,1 2.927,1.198 0.458,0.198 10 false I17 2.469,1.427 2.927,1.625 0.458,0.198 10 false I17 2.458,2.656 2.917,2.854 0.458,0.198 10 false I18 2.458,3.875 2.917,4.073 0.458,0.198 10 false I18 2.469,4.396 2.927,4.594 0.458,0.198 10 false I18 3.583,0.469 3.74,0.667 0.156,0.198 10 false 7 3.583,0.875 3.74,1.073 0.156,0.198 10 false 6 3.583,1.323 3.74,1.521 0.156,0.198 10 false 5 3.802,0.563 4.417,0.76 0.615,0.198 10 false RLID 3.802,1 4.417,1.198 0.615,0.198 10 false RCID 3.802,1.417 4.417,1.615 0.615,0.198 10 false RRID 5.021,1 5.635,1.198 0.615,0.198 10 false IG+ 5.417,0.885 5.573,1.083 0.156,0.198 10 false 8 5.667,1.167 6.292,1.583 0.625,0.417 10 false ECU-IG1 NO. 2 6.469,0.99 7.156,1.479 0.688,0.49 10 false IG1 NO. 2 Relay 4.042,1.781 4.656,1.979 0.615,0.198 10 false I170 4.021,1.958 5.219,2.24 1.198,0.281 10 false Clock Assembly 3.563,2.563 3.719,2.76 0.156,0.198 10 false 1 5.385,2.563 5.542,2.76 0.156,0.198 10 false 2 3.281,2.917 3.896,3.115 0.615,0.198 10 false N41 3.167,4.99 6.083,5.24 2.917,0.25 10 false Rear Seat Inner with Center Belt Assembly RH 3.563,3.74 3.719,3.938 0.156,0.198 10 false 2 3.563,4.281 3.719,4.479 0.156,0.198 10 false 4 5.417,3.75 5.573,3.948 0.156,0.198 10 false 3 5.427,4.25 5.583,4.448 0.156,0.198 10 false 5 4.24,4.031 5.438,4.313 1.198,0.281 10 false (for Center) 4.313,4.552 5.51,4.833 1.198,0.281 10 false (for RH) 0.542,4.917 2.458,5.167 1.917,0.25 10 false Combination Meter Assembly 3.177,4.802 3.792,5 0.615,0.198 10 false O30 3.281,3.083 6.198,3.333 2.917,0.25 10 false Rear Seat Inner with Center Belt Assembly LH 1.833,6.052 2.448,6.25 0.615,0.198 10 false LCTY 1.833,6.885 2.448,7.083 0.615,0.198 10 false RCTY 2.427,5.885 2.583,6.083 0.156,0.198 10 false 1 2.438,6.75 2.594,6.948 0.156,0.198 10 false 6 3.563,5.906 3.719,6.104 0.156,0.198 10 false 1 3.563,6.74 3.719,6.938 0.156,0.198 10 false 1 3.167,6.229 3.781,6.427 0.615,0.198 10 false N15 3.167,6.406 6.083,6.656 2.917,0.25 10 false Rear Door Courtesy Light Switch Assembly LH 3.167,7.115 3.781,7.313 0.615,0.198 10 false O16 3.167,7.302 6.083,7.552 2.917,0.25 10 false Rear Door Courtesy Light Switch Assembly RH 0.51,7.385 0.833,7.583 0.323,0.198 10 false I13 0.5,7.563 2.167,8.063 1.667,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 0.792,8.354 3.708,8.604 2.917,0.25 10 false : CAN Communication Line 3.688,7.948 6.531,8.24 2.844,0.292 10 false *1: for RHD without Multi-information Display 3.698,8.271 6.542,8.563 2.844,0.292 10 false *2: for RHD with Multi-information Display

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch signal ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch signal ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

ON or OFF appears on the tester screen according to the rear door condition.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT BELT WARNING

NG

2.CHECK REAR SEAT BELT WARNING
a.
B294180C02
1.115,1.438 1.115,1.833 false 1.698,1.438 1.698,1.833 false 2.292,1.438 2.292,1.833 false 0.219,0.188 0.521,0.531 0.302,0.344 10 false *a 1.042,1.854 1.302,2.104 0.26,0.25 10 false *b 1.625,1.854 1.917,2.083 0.292,0.229 10 false *c 2.219,1.854 2.583,2.156 0.365,0.302 10 false *d
*a Rear Seat Belt Warning Light (Clock Assembly)
*b LH
*c Center
*d RH


Check the rear seat belt warning function.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION


Result:
Result Proceed to
The rear seat belt warning lights operation is normal A
The rear seat belt warning lights (all seat) operation is not normal B
The rear seat belt warning light (RH) operation is not normal C
The rear seat belt warning light (center) operation is not normal D
The rear seat belt warning light (LH) operation is not normal E



A

B

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)

C

6.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR RH))

D

10.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))

E

14.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light ON/OFF -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

4.CHECK HARNESS AND CONNECTOR (BATTERY - CLOCK ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BATTERY - CLOCK ASSEMBLY)
a.

Disconnect the I170 clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I170-8 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Reconnect the I170 clock assembly connector.


b.

Disconnect the I17 combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I17-9 (RLMT) - Body ground*1 Ignition switch ON 11 to 14 V
I17-6 (RLMT) - Body ground*2 Ignition switch ON 11 to 14 V
I17-10 (RCMT) - Body ground*1 Ignition switch ON 11 to 14 V
I17-2 (RCMT) - Body ground*2 Ignition switch ON 11 to 14 V
I17-11 (RRMT) - Body ground*1 Ignition switch ON 11 to 14 V
I17-3 (RRMT) - Body ground*2 Ignition switch ON 11 to 14 V


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE CLOCK ASSEMBLY

6.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR RH))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear RH seat belt buckle switch signal ON or OFF ON: Rear RH seat belt fastened
OFF: Rear RH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
50003 122 74

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR RH) - BODY GROUND)

B

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR RH) - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the O30 rear seat inner with center belt assembly RH (for RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-5 (RRSB) - O30-4*1 Always Below 1 Ω
I18-6 (RRSB) - O30-4*2 Always Below 1 Ω
I18-5 (RRSB) - Body ground*1 Always 10 kΩ or higher
I18-6 (RRSB) - Body ground*2 Always 10 kΩ or higher
O30-5 - Body ground Always Below 1 Ω


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light ON/OFF -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

9.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-11 (RRMT) - I170-5 (RRID)*1 Always Below 1 Ω
I17-3 (RRMT) - I170-5 (RRID)*2 Always Below 1 Ω
I17-11 (RRMT) - Body ground*1 Always 10 kΩ or higher
I17-3 (RRMT) - Body ground*2 Always 10 kΩ or higher


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (C) Rear center seat belt buckle switch signal ON or OFF ON: Rear center seat belt fastened
OFF: Rear center seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (C)
50003 122 76

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR CENTER) - BODY GROUND)

B

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR CENTER) - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the O30 rear seat inner with center belt assembly RH (for center) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-4 (RCSB) - O30-2*1 Always Below 1 Ω
I18-5 (RCSB) - O30-2*2 Always Below 1 Ω
I18-4 (RCSB) - Body ground*1 Always 10 kΩ or higher
I18-5 (RCSB) - Body ground*2 Always 10 kΩ or higher
O30-3 - Body ground Always Below 1 Ω


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FOR CENTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light ON/OFF -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

13.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-10 (RCMT) - I170-6 (RCID)*1 Always Below 1 Ω
I17-2 (RCMT) - I170-6 (RCID)*2 Always Below 1 Ω
I17-10 (RCMT) - Body ground*1 Always 10 kΩ or higher
I17-2 (RCMT) - Body ground*2 Always 10 kΩ or higher


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (L) Rear LH seat belt buckle switch signal ON or OFF ON: Rear LH seat belt fastened
OFF: Rear LH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (L)
50003 122 75

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT LH - BODY GROUND)

B

16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT LH - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the N41 rear seat inner with center belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (RLSB) - N41-1*1 Always Below 1 Ω
I18-10 (RLSB) - N41-1*2 Always Below 1 Ω
I18-3 (RLSB) - Body ground*1 Always 10 kΩ or higher
I18-10 (RLSB) - Body ground*2 Always 10 kΩ or higher
N41-2 - Body ground Always Below 1 Ω


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light ON/OFF -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-9 (RLMT) - I170-7 (RLID)*1 Always Below 1 Ω
I17-6 (RLMT) - I170-7 (RLID)*2 Always Below 1 Ω
I17-9 (RLMT) - Body ground*1 Always 10 kΩ or higher
I17-6 (RLMT) - Body ground*2 Always 10 kΩ or higher


*1: for RHD without Multi-information Display

*2: for RHD with Multi-information Display



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR