1. REPAIR INSTRUCTION
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Do not heat the vehicle body excessively.
Wipe off any No. 1 luggage compartment door name plate or rear door lower outside stripe adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface and No. 1 luggage compartment door name plate or rear door lower outside stripe down to between 20 and 30°C (68 and 86°F) prior to installation.
The most appropriate temperature for installing the No. 1 luggage compartment door name plate or rear door lower outside stripe is 25°C (77°F).
When the temperature is low, the No. 1 luggage compartment door name plate or rear door lower outside stripe becomes stiff and comes off easily. When the temperature is high, the No. 1 luggage compartment door name plate or rear door lower outside stripe elasticity increases.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the No. 1 luggage compartment door name plate or rear door lower outside stripe will be installed. If any roughness or dirt remains when pressing the No. 1 luggage compartment door name plate or rear door lower outside stripe onto the surface, air will be trapped under the No. 1 luggage compartment door name plate or rear door lower outside stripe and result in a poor appearance.
Spray water on the shop floor to settle any dust.
Key points for handling the No. 1 luggage compartment door name plate and rear door lower outside stripe
The No. 1 luggage compartment door name plate and rear door lower outside stripe bend and roll up easily. Store them between flat pieces of cardboard or other similar objects and keep them dry and flat.
Do not bend the No. 1 luggage compartment door name plate or rear door lower outside stripe or leave it in high temperature places.
Key points for installation of the No. 1 luggage compartment door name plate or rear door lower outside stripe (How to use a squeegee and installation procedure for flat surfaces)
Position the No. 1 luggage compartment door name plate or rear door lower outside stripe accurately to achieve a neat finish and to avoid peeling.
The No. 1 luggage compartment door name plate or rear door lower outside stripe cannot be reused because it deforms after removal.
To avoid air bubbles, slightly raise the part of the No. 1 luggage compartment door name plate or rear door lower outside stripe that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the No. 1 luggage compartment door name plate or rear door lower outside stripe onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.
| *A | Pressing Forward | *B | Pulling |
| *1 | No. 1 Luggage Compartment Door Name Plate or Rear Door Lower Outside Stripe | - | - |
| *a | Side View | *b | Non-padded Side |
| *c | Padded Side | *d | Squeegee |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) | B | 40 to 50° (for pressing forward) |
| C | 30 to 45° (for pulling) | - | - |
Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.
Either angle of the squeegee (pressing forward or pulling) is acceptable.
Check after installation
After completing the installation, check if the No. 1 luggage compartment door name plate or rear door lower outside stripe is installed neatly. If it is not installed neatly, install a new No. 1 luggage compartment door name plate or new rear door lower outside stripe.
Do not reuse the No. 1 luggage compartment door name plate or rear door lower outside stripe.
75978H
2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH
| *a | Edge of Rear Door Panel LH Curved Surface |
Remove the release paper and install a new rear door lower outside stripe LH to the area shown in the illustration.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Remove the application sheet from the rear door lower outside stripe LH as shown in the illustration.
75977H
3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE RH
| *a | Edge of Rear Door Panel RH Curved Surface |
Remove the release paper and install a new rear door lower outside stripe RH to the area shown in the illustration.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Remove the application sheet from the rear door lower outside stripe RH as shown in the illustration.
75441A
4.INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE
| *a | Edge of Luggage Compartment Door Curved Surface |
Remove the release paper and install a new No. 1 luggage compartment door name plate to the area shown in the illustration.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Remove the application sheet from the No. 1 luggage compartment door name plate as shown in the illustration.