The meter ECU receives vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores DTCs. Troubleshoot the vehicle stability control system or anti-lock brake system.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
Before starting the following inspection, check tire size and tire air pressure.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | OFF, 0, 40, 80, 120, 160, 200, 240 | There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)
·
40 → 41.4 to 45.9 ·
80 → 82.8 to 87.8 ·
120 → 124.1 to 129.1 ·
160 → 165.5 to 170.5 ·
200 → 206.9 to 211.9 |
| Tester Display |
|---|
| Speed Meter Operation |
Speedometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if vehicle stability control system DTCs are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.
for Combination Meter: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| Vehicle Speed Meter |
| Tester Display |
|---|
| Vehicle Speed |
| Result | Proceed to |
|---|---|
| The data list values of the ECUs match. | A |
| The data list values of the ECUs do not match. | B |
When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) or an internal malfunction of the combination meter assembly is suspected.
A
B
Replace the combination meter assembly with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
| Result | Proceed to |
|---|---|
| The operation of the speedometer returns to normal. | A |
| The operation of the speedometer does not return to normal. | B |
A
B