DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body, Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Dimmer SW | Dimmer switch high position signal | ON or OFF | ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position |
- |
| Passing Light SW | Dimmer switch high flash position (pass) signal | ON or OFF | ON: Dimmer switch in high flash position
OFF: Dimmer switch not in high flash position |
- |
| Rear Fog Light SW | Rear fog light switch signal | ON or OFF | ON: Rear fog light switch on
OFF: Rear fog light switch off |
w/ Rear Fog Light |
| Auto Light SW | Light control switch AUTO position signal | ON or OFF | ON: Light control switch in AUTO position
OFF: Light control switch not in AUTO position |
w/ Automatic Light Control |
| Head Light SW (Head) | Light control switch head position signal | ON or OFF | ON: Light control switch in head position
OFF: Light control switch not in head position |
- |
| Head Light SW (Tail) | Light control switch tail position signal | ON or OFF | ON: Light control switch in tail or head position
OFF: Light control switch in neither tail nor head position |
- |
| Illumination Rate Info | Illumination rate information | 0.00 ms. to 2162.65 ms. | Value is output according to ambient light levels | - |
| Response Time | Delay timing of lighting the taillights when the automatic light control sensor detects brightness change | Normal or Long | Customize setting displayed | - |
| Sensitivity | Sensitivity of the automatic light control system | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex ON Sen | Ambient brightness level required to dim display lights (combination meter, navigation display etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex OFF Sen | Ambient brightness level required to cancel dimming display lights (combination meter, navigation display etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Signal Switch (Right) | Turn signal switch (Right) signal | ON or OFF | ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off |
- |
| Turn Signal Switch (Left) | Turn signal switch (Left) signal | ON or OFF | ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off |
- |
| Hazard Flasher Switch | Hazard switch signal | ON or OFF | ON: Hazard switch on
OFF: Hazard switch off |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime running lights | ON/OFF | w/ Daytime Running Light |
| Taillight Relay | Taillight relay | ON/OFF | - |
| Headlight Relay | Headlight relays | ON/OFF | - |
| Head Light Hi | High beam headlights | ON/OFF | - |
| Rear Fog Light Relay | Rear fog light relay | ON/OFF | ·
Make sure the light control switch is in the tail position ·
w/ Rear Fog Light |
| Dimmer Signal | Dimmer signal | ON/OFF | - |