84250A
1.INSPECT STEERING PAD SWITCH ASSEMBLY (Type A)
Measure the resistance according to the value(s) in the table below.
| *A | w/ Microphone | - | - |
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | MODE/HOLD |
| *e | Seek+ | *f | Seek- |
| *g | Off Hook | *h | On Hook |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-1 (HO) - A-1(HO) | Always | Below 2.5 Ω |
| z3-11 (AU1) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z3-10 (AU2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed* | 313 to 345 Ω | |
| Off hook switch pushed* | 950 to 1050 Ω |
*: w/ Microphone
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.
Check that the switch illumination illuminates.
The steering pad switch illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.
84250A
2.INSPECT STEERING PAD SWITCH ASSEMBLY (Type B)
Measure the resistance according to the value(s) in the table below.
| *A | w/ Voice switch | *B | w/ Shift Paddle Switch |
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | Back |
| *e | MODE/HOLD | *f | Up |
| *g | Down | *h | Left |
| *i | Right | *j | Enter |
| *k | Off Hook | *l | On Hook |
| *m | Voice | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-1 (HO) - A-1(HO) | Always | Below 2.5 Ω |
| z3-11 (AU1) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Up switch pushed | Below 2.5 Ω | |
| Down switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z3-10 (AU2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed*1 | 2955 to 3265 Ω | |
| z3-9 (AU3) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω | |
| z3-6 (SUP) - SR-2 (SUP)*2 | Always | Below 2.5 Ω |
| z3-7 (ECC) - SR-7 (ECC)*2 | Always | Below 2.5 Ω |
| z3-12 (SDN) - SR-3 (SDN)*2 | Always | Below 2.5 Ω |
*1: w/ Voice Switch
*2: w/ Shift Paddle Switch
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.
Check that the switch illumination illuminates.
The steering pad switch illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.
84250A
3.INSPECT STEERING PAD SWITCH ASSEMBLY (Type C)
Measure the resistance according to the value(s) in the table below.
| *A | w/ Dynamic Radar Cruise Control System | *B | w/ Shift Paddle Switch |
| *C | w/ Voice Switch | - | - |
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | Back (LH) |
| *e | MODE/HOLD | *f | Up (LH) |
| *g | Down (LH) | *h | Left |
| *i | Right | *j | Enter (LH) |
| *k | Off Hook | *l | On Hook |
| *m | Back (RH) | *n | Up (RH) |
| *o | Down (RH) | *p | Page |
| *q | Enter (RH) | *r | Voice |
| *s | Distance control | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-1 (HO) - A-1(HO) | Always | Below 2.5 Ω |
| z3-11 (AU1) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Up (LH) switch pushed | Below 2.5 Ω | |
| Down (LH) switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z3-10 (AU2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed*1 | 2955 to 3265 Ω | |
| z3-9 (AU3) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter (LH) switch pushed | Below 2.5 Ω | |
| Back (LH) switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω | |
| z3-3 (+DP2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Back (RH) switch pushed | Below 2.5 Ω | |
| Up (RH) switch pushed | 313 to 345 Ω | |
| Down (RH) switch pushed | 950 to 1050 Ω | |
| Page switch pushed | 2955 to 3265 Ω | |
| z3-2 (+DP) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter (RH) switch pushed | Below 2.5 Ω | |
| z3-6 (SUP) - SR-2 (SUP)*2 | Always | Below 2.5 Ω |
| z3-7 (ECC) - SR-7 (ECC)*2 | Always | Below 2.5 Ω |
| z3-12 (SDN) - SR-3 (SDN)*2 | Always | Below 2.5 Ω |
| z3-4 (DIST) - z3-7 (ECC)*3 | No switch pushed | 1 MΩ or higher |
| Distance control switch pushed | Below 2.5 Ω |
*1: w/ Voice Switch
*2: w/ Shift Paddle Switch
*3: w/ Dynamic Radar Cruise Control System
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.
Check that the switch illumination illuminates.
The steering pad switch illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.