Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Brake actuator assembly

·

Steering sensor

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (certification ECU)*1

·

Navigation receiver assembly*2

·

Radio and display receiver assembly*3

·

Network gateway ECU*4

·

Clearance warning ECU assembly*5

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: w/ Smart Entry and Start System

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Parking Assist Monitor System

*5: w/ Toyota Parking Assist-sensor System

WIRING DIAGRAM

C325235E02
0.063,0.073 1.167,0.313 1.104,0.24 12 false V Bus: 3.448,0.427 4.219,0.625 0.771,0.198 10 false 120 Ω 4.104,1 4.719,1.198 0.615,0.198 10 false CANH 2.771,1 3.385,1.198 0.615,0.198 10 false CANL 4.104,1.271 4.417,1.469 0.313,0.198 10 false 16 3.01,1.26 3.323,1.458 0.313,0.198 10 false 15 4.146,1.521 4.302,1.719 0.156,0.198 10 false R 2.979,1.51 3.135,1.708 0.156,0.198 10 false W 4.26,1.771 4.417,1.969 0.156,0.198 10 false 1 2.917,1.792 3.073,1.99 0.156,0.198 10 false 2 3.177,1.865 3.635,2.063 0.458,0.198 10 false I94 3.948,1.865 4.406,2.063 0.458,0.198 10 false I94 0.125,2.958 0.583,3.156 0.458,0.198 10 false I13 0.875,0.615 2.875,0.896 2,0.281 10 false Combination Meter Assembly 0.635,0.615 1.094,0.813 0.458,0.198 10 false I18 4.948,0.219 6.26,0.49 1.313,0.271 10 false x: Suspected Area 0.365,2.958 2.042,3.448 1.677,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 1.052,2.094 1.667,2.292 0.615,0.198 10 false CANH 1.052,2.698 1.667,2.896 0.615,0.198 10 false CANL 1.531,2.094 1.844,2.292 0.313,0.198 10 false 14 1.531,2.708 1.844,2.906 0.313,0.198 10 false 13 2.229,2.031 2.385,2.229 0.156,0.198 10 false P 2.208,2.792 2.365,2.99 0.156,0.198 10 false W 2.677,2.219 3.135,2.417 0.458,0.198 10 false I95 2.677,2.583 3.135,2.781 0.458,0.198 10 false I95 2.719,2.021 2.875,2.219 0.156,0.198 10 false 1 2.719,2.792 2.875,2.99 0.156,0.198 10 false 2 0.146,4.833 0.604,5.031 0.458,0.198 10 false I29 0.385,4.833 1.583,5.115 1.198,0.281 10 false Steering Sensor 1.052,3.948 1.667,4.146 0.615,0.198 10 false CANH 1.052,4.563 1.667,4.76 0.615,0.198 10 false CANL 1.563,3.979 1.719,4.177 0.156,0.198 10 false 3 1.563,4.573 1.719,4.771 0.156,0.198 10 false 2 2.229,3.865 2.385,4.063 0.156,0.198 10 false V 2.198,4.656 2.354,4.854 0.156,0.198 10 false W 2.677,4.448 3.031,4.688 0.354,0.24 10 false I97 2.677,4.083 3.031,4.323 0.354,0.24 10 false I97 2.719,3.875 2.875,4.073 0.156,0.198 10 false 1 2.719,4.667 2.875,4.865 0.156,0.198 10 false 2 0.229,6.563 0.542,6.76 0.313,0.198 10 false j1 0.396,6.573 1.396,7.063 1,0.49 10 false Power Steering ECU Assembly 1.052,5.708 1.667,5.906 0.615,0.198 10 false CANH 1.063,6.323 1.677,6.521 0.615,0.198 10 false CANL 1.563,5.667 1.719,5.865 0.156,0.198 10 false 4 1.552,6.333 1.708,6.531 0.156,0.198 10 false 8 1.74,5.594 1.896,5.792 0.156,0.198 10 false Y 1.698,6.469 2.01,6.667 0.313,0.198 10 false SB 2.302,5.594 2.458,5.792 0.156,0.198 10 false G 2.281,6.479 2.438,6.677 0.156,0.198 10 false W 2.625,5.833 3.24,6.031 0.615,0.198 10 false I100 2.625,6.198 3.24,6.396 0.615,0.198 10 false I100 2.698,5.594 2.854,5.792 0.156,0.198 10 false 1 2.708,6.417 2.865,6.615 0.156,0.198 10 false 2 3.177,6.688 3.635,6.885 0.458,0.198 10 false I93 3.948,6.688 4.406,6.885 0.458,0.198 10 false I93 4.146,6.99 4.302,7.188 0.156,0.198 10 false B 2.99,6.99 3.146,7.188 0.156,0.198 10 false W 4.427,2.281 6.479,2.573 2.052,0.292 10 false CAN No. 1 Junction Connector 4.417,3.094 5.031,3.292 0.615,0.198 10 false I103 4.417,3.469 5.031,3.667 0.615,0.198 10 false I103 4.271,6.677 4.427,6.875 0.156,0.198 10 false 1 2.938,6.688 3.094,6.885 0.156,0.198 10 false 2 4.5,2.875 4.656,3.073 0.156,0.198 10 false 1 4.5,3.688 4.656,3.885 0.156,0.198 10 false 2 5.208,2.885 5.365,3.083 0.156,0.198 10 false Y 5.188,3.688 5.344,3.885 0.156,0.198 10 false W 5.813,3.854 6.271,4.052 0.458,0.198 10 false I47 6.063,3.854 6.979,4.302 0.917,0.448 10 false Airbag Sensor Assembly 5.844,2.99 6.458,3.188 0.615,0.198 10 false CANH 5.844,3.594 6.458,3.792 0.615,0.198 10 false CANL 5.573,2.979 5.885,3.177 0.313,0.198 10 false 13 5.583,3.594 5.896,3.792 0.313,0.198 10 false 22 4.438,5.156 4.896,5.354 0.458,0.198 10 false I96 4.438,4.792 4.896,4.99 0.458,0.198 10 false I96 4.479,4.594 4.635,4.792 0.156,0.198 10 false 1 4.5,5.365 4.656,5.563 0.156,0.198 10 false 2 6.177,5.333 6.635,5.531 0.458,0.198 10 false I39 5.885,4.75 6.5,4.948 0.615,0.198 10 false CANH 6.052,5.094 6.667,5.292 0.615,0.198 10 false CANL 5.667,4.635 5.823,4.833 0.156,0.198 10 false 6 5.833,5.271 6.146,5.469 0.313,0.198 10 false 14 6.427,5.333 7.042,5.531 0.615,0.198 10 false DLC3 5.219,4.583 5.375,4.781 0.156,0.198 10 false L 5.188,5.375 5.344,5.573 0.156,0.198 10 false W 0.813,8 2.813,8.292 2,0.292 10 false : CAN Main Bus Line (CANH) 0.823,8.427 2.771,8.677 1.948,0.25 10 false : CAN Main Bus Line (CANL) 3.958,7.99 5.885,8.24 1.927,0.25 10 false : CAN Branch Line (CANH) 3.969,8.406 5.865,8.698 1.896,0.292 10 false : CAN Branch Line (CANL)

C355178E01
0.156,0.073 1.26,0.313 1.104,0.24 12 false V Bus: 4.448,5.01 6.49,5.375 2.042,0.365 10 false CAN No. 2 Junction Connector 4.375,2.26 4.719,2.521 0.344,0.26 10 false I105 3.865,0.396 4.208,0.656 0.344,0.26 10 false I101 3.104,0.396 3.448,0.656 0.344,0.26 10 false I101 4.229,0.385 4.573,0.646 0.344,0.26 10 false 1 4.458,0.427 4.802,0.688 0.344,0.26 10 false 1 4.448,2.083 4.792,2.344 0.344,0.26 10 false 1 4.458,3.615 4.802,3.875 0.344,0.26 10 false 1 4.25,5.396 4.594,5.656 0.344,0.26 10 false 1 2.677,4.385 3.021,4.646 0.344,0.26 10 false 1 2.667,2.49 3.01,2.75 0.344,0.26 10 false 1 2.667,0.573 3.01,0.833 0.344,0.26 10 false 1 2.896,0.385 3.24,0.646 0.344,0.26 10 false 2 2.677,1.323 3.021,1.583 0.344,0.26 10 false 2 2.677,3.313 3.021,3.573 0.344,0.26 10 false 2 2.677,5.146 3.021,5.406 0.344,0.26 10 false 2 2.917,5.396 3.26,5.656 0.344,0.26 10 false 2 4.469,4.385 4.813,4.646 0.344,0.26 10 false 2 4.469,2.823 4.813,3.083 0.344,0.26 10 false 2 4.479,1.198 4.823,1.458 0.344,0.26 10 false 2 4.375,0.604 4.719,0.865 0.344,0.26 10 false I106 4.375,0.979 4.719,1.24 0.344,0.26 10 false I106 5.156,0.448 5.5,0.708 0.344,0.26 10 false L 5.146,1.146 5.49,1.406 0.344,0.26 10 false W 5.563,0.51 5.906,0.771 0.344,0.26 10 false 14 5.813,0.51 6.25,0.729 0.438,0.219 10 false CANH 5.802,1.083 6.24,1.302 0.438,0.219 10 false CANL 5.563,1.094 5.906,1.354 0.344,0.26 10 false 15 5.479,1.354 7.135,1.802 1.656,0.448 10 false Smart Key ECU Assembly (Certification ECU)*1 5.25,1.354 5.5,1.604 0.25,0.25 10 false I78 2.583,0.75 2.927,1.01 0.344,0.26 10 false I107 2.573,1.125 2.917,1.385 0.344,0.26 10 false I107 2.063,1.292 2.406,1.552 0.344,0.26 10 false W 2.083,0.615 2.427,0.875 0.344,0.26 10 false R 0.052,1.49 0.458,1.74 0.406,0.25 10 false I155 1.031,0.656 1.469,0.875 0.438,0.219 10 false CANH 1.052,1.229 1.49,1.448 0.438,0.219 10 false CANL 1.521,0.646 1.865,0.906 0.344,0.26 10 false 9 1.51,1.24 1.854,1.5 0.344,0.26 10 false 10 0.344,1.5 2.854,1.792 2.51,0.292 10 false Radio and Display Receiver Assembly*2 0.104,1.813 0.51,2.063 0.406,0.25 10 false I67 0.344,1.823 2.854,2.115 2.51,0.292 10 false Navigation Receiver Assembly*3 4.365,2.625 4.708,2.885 0.344,0.26 10 false I105 4.833,2.802 5.177,3.063 0.344,0.26 10 false W 5.365,2.802 5.708,3.063 0.344,0.26 10 false W 4.854,2.104 5.198,2.365 0.344,0.26 10 false Y 5.313,2.125 5.656,2.385 0.344,0.26 10 false GR 5.552,2.75 5.896,3.01 0.344,0.26 10 false 14 5.552,2.125 5.896,2.385 0.344,0.26 10 false 26 5.813,2.125 6.25,2.344 0.438,0.219 10 false CANH 5.802,2.729 6.24,2.948 0.438,0.219 10 false CANL 5.219,3.01 5.698,3.271 0.479,0.26 10 false A49 5.521,3 7.104,3.302 1.583,0.302 10 false Brake Actuator Assembly 1.031,2.656 1.469,2.875 0.438,0.219 10 false CANH 1.052,3.24 1.49,3.458 0.438,0.219 10 false CANL 2.583,2.76 2.927,3.021 0.344,0.26 10 false I102 2.573,3.125 2.917,3.385 0.344,0.26 10 false I102 2.073,2.594 2.417,2.854 0.344,0.26 10 false V 2.073,3.292 2.417,3.552 0.344,0.26 10 false W 1.51,2.646 1.854,2.906 0.344,0.26 10 false 11 1.51,3.24 1.854,3.5 0.344,0.26 10 false 12 0.083,3.5 0.49,3.75 0.406,0.25 10 false I77 0.323,3.51 2.594,3.823 2.271,0.313 10 false Air Conditioning Amplifier Assembly 4.385,3.813 4.729,4.073 0.344,0.26 10 false I161 4.375,4.177 4.719,4.438 0.344,0.26 10 false I161 5.135,4.344 5.479,4.604 0.344,0.26 10 false W 5.135,3.667 5.479,3.927 0.344,0.26 10 false G 5.802,3.708 6.24,3.927 0.438,0.219 10 false CA1H 5.833,4.292 6.271,4.51 0.438,0.219 10 false CA1L 5.552,3.708 5.896,3.969 0.344,0.26 10 false 16 5.552,4.302 5.896,4.563 0.344,0.26 10 false 15 5.229,4.552 5.667,4.771 0.438,0.219 10 false I160 5.531,4.552 7.083,4.917 1.552,0.365 10 false Network Gateway ECU*4 3.865,5.396 4.208,5.656 0.344,0.26 10 false I104 3.115,5.385 3.458,5.646 0.344,0.26 10 false I104 2.979,5.823 3.323,6.083 0.344,0.26 10 false W 2.99,6.458 3.333,6.719 0.344,0.26 10 false W 4.083,6.458 4.427,6.719 0.344,0.26 10 false B 4.083,5.823 4.427,6.083 0.344,0.26 10 false P 2.063,5.125 2.406,5.385 0.344,0.26 10 false W 2.031,4.417 2.375,4.677 0.344,0.26 10 false BE 2.583,4.573 2.927,4.833 0.344,0.26 10 false I177 2.583,4.948 2.927,5.208 0.344,0.26 10 false I177 1.51,4.469 1.854,4.729 0.344,0.26 10 false 17 1.521,5.052 1.865,5.313 0.344,0.26 10 false 18 1.26,4.469 1.604,4.729 0.344,0.26 10 false R1 1.24,5.063 1.583,5.323 0.344,0.26 10 false R2 0.052,5.323 0.458,5.573 0.406,0.25 10 false I82 0.281,5.333 2.552,5.646 2.271,0.313 10 false Clearance Warning ECU Assembly*5 4.677,6.427 6.896,6.885 2.219,0.458 10 false *5: w/ Toyota Parking Assist-sensor System 3.042,6.74 3.385,7 0.344,0.26 10 false 26 4.052,6.75 4.396,7.01 0.344,0.26 10 false 13 2.792,6.958 3.229,7.177 0.438,0.219 10 false CANL 4.104,6.958 4.542,7.177 0.438,0.219 10 false CANH 3.438,7.542 3.875,7.76 0.438,0.219 10 false 120 Ω 0.792,8.094 2.677,8.344 1.885,0.25 10 false : CAN Main Bus Line (CANH) 0.792,8.479 2.677,8.729 1.885,0.25 10 false : CAN Main Bus Line (CANL) 3.948,8.125 5.833,8.375 1.885,0.25 10 false : CAN Branch Line (CANH) 3.948,8.51 5.833,8.76 1.885,0.25 10 false : CAN Branch Line (CANL) 0.125,5.99 2.458,6.344 2.333,0.354 10 false *1: w/ Smart Entry and Start System 0.135,6.302 2.469,6.656 2.333,0.354 10 false *2: for Radio and Display Type 0.135,6.615 2.469,6.969 2.333,0.354 10 false *3: for Navigation Receiver Type 4.656,5.781 6.948,6.281 2.292,0.5 10 false *4: w/ Parking Assist Monitor System 4.646,7.25 5.427,7.458 0.781,0.208 10 false A25 5,7.25 5.781,7.458 0.781,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C247963C04
1.063,2 1.521,2.281 0.458,0.281 1.969,2.26 2.25,2.073 2.25,2.073 2.344,2.073 true 1.958,2.406 2.24,2.552 2.24,2.552 2.344,2.552 true 1.729,2.323 1.51,1.813 1.51,1.813 1.406,1.813 false 1.792,2.448 2,2.979 2,2.979 2.125,2.979 true 0.115,0.135 0.427,0.427 0.313,0.292 10 false *a 2.385,1.99 3.063,2.229 0.677,0.24 10 false CANH*b 2.396,2.479 3.042,2.708 0.646,0.229 10 false CANL*b 1.198,2.063 1.469,2.302 0.271,0.24 10 false I96 1.302,1.74 1.458,1.979 0.156,0.24 10 false L 2.188,2.906 2.344,3.146 0.156,0.24 10 false W
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to DLC3


Disconnect the I96 DLC3 branch line connector from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C292403C42
1.458,0.167 1.885,0.406 0.427,0.24 0.917,0.333 1.115,0.333 1.115,0.333 1.594,0.781 true 1.615,1.917 1.823,1.917 1.823,1.917 2.042,1.5 true 2.406,0.302 2.188,0.302 2.188,0.302 2.042,0.781 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *1 1.563,0.198 1.875,0.396 0.313,0.198 10 false I39 2.49,0.219 3.104,0.417 0.615,0.198 10 false CANH 1.177,1.844 1.792,2.042 0.615,0.198 10 false CANL 0.635,0.271 1.021,0.51 0.385,0.24 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Reconnect the I96 DLC3 branch line connector to the CAN No. 1 junction connector.


b.
C292403C42
1.458,0.167 1.885,0.406 0.427,0.24 0.917,0.333 1.115,0.333 1.115,0.333 1.594,0.781 true 1.615,1.917 1.823,1.917 1.823,1.917 2.042,1.5 true 2.406,0.302 2.188,0.302 2.188,0.302 2.042,0.781 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *1 1.563,0.198 1.875,0.396 0.313,0.198 10 false I39 2.49,0.219 3.104,0.417 0.615,0.198 10 false CANH 1.177,1.844 1.792,2.042 0.615,0.198 10 false CANL 0.635,0.271 1.021,0.51 0.385,0.24 10 false CG
*1 DLC3


Disconnect the connectors from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.

HINT:

Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.



c.

Using an electrical tester, measure the resistance between terminals 6 (CANH) and 4 (CG), or between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

C325241C02
0.229,1.438 0.385,1.635 0.156,0.198 10 false P 0.76,1.438 0.917,1.635 0.156,0.198 10 false W 0.479,2.396 1.552,2.594 1.073,0.198 10 false *1 1.469,1.677 1.781,1.875 0.313,0.198 10 false *2 2.51,2.396 2.823,2.594 0.313,0.198 10 false *3 2.281,1.052 2.438,1.25 0.156,0.198 10 false G 2.792,1.823 3.073,2.063 0.281,0.24 10 false SB 2.302,1.823 2.615,2.021 0.313,0.198 10 false Y 2.781,1.052 2.938,1.25 0.156,0.198 10 false W 3.781,1.667 4.854,1.865 1.073,0.198 10 false *4 3.531,1.063 3.688,1.26 0.156,0.198 10 false Y 4.031,1.063 4.188,1.26 0.156,0.198 10 false W 4.75,2.375 5.063,2.573 0.313,0.198 10 false *5 4.51,1.49 4.667,1.688 0.156,0.198 10 false L 5.031,1.49 5.188,1.688 0.156,0.198 10 false W 5.771,1.688 6.083,1.885 0.313,0.198 10 false *6 5.521,1.104 5.677,1.302 0.156,0.198 10 false R 6.073,1.104 6.229,1.302 0.156,0.198 10 false W 6.365,2.802 6.521,3 0.156,0.198 10 false B 6.885,2.802 7.042,3 0.156,0.198 10 false W 0.073,3.594 0.229,3.792 0.156,0.198 10 false B 0.563,3.594 0.719,3.792 0.156,0.198 10 false W 0.865,4.104 1.573,4.333 0.708,0.229 10 false *7 (*A) 0.865,4.313 1.573,4.542 0.708,0.229 10 false *8 (*B) 1.906,4.865 2.219,5.063 0.313,0.198 10 false *9 1.688,5.25 1.844,5.448 0.156,0.198 10 false B 1.688,5.688 1.844,5.885 0.156,0.198 10 false P 2.156,5.25 2.313,5.448 0.156,0.198 10 false W 2.167,5.688 2.323,5.885 0.156,0.198 10 false W 2.865,4.198 3.323,4.396 0.458,0.198 10 false *10 2.625,4.781 2.875,4.979 0.25,0.198 10 false GR 3.167,4.781 3.479,4.979 0.313,0.198 10 false W 2.698,5.563 2.854,5.76 0.156,0.198 10 false Y 3.177,5.563 3.333,5.76 0.156,0.198 10 false W 3.844,4.865 4.302,5.063 0.458,0.198 10 false *11 4.771,4.208 5.417,4.438 0.646,0.229 10 false *12 (*C) 5.552,4.865 6.135,5.083 0.583,0.219 10 false *13 (*D) 3.667,5.479 3.823,5.677 0.156,0.198 10 false V 4.135,5.479 4.292,5.677 0.156,0.198 10 false W 4.698,5.188 4.854,5.385 0.156,0.198 10 false L 5.188,5.188 5.344,5.385 0.156,0.198 10 false W 5.469,5.5 5.625,5.698 0.156,0.198 10 false G 5.979,5.5 6.135,5.698 0.156,0.198 10 false W 6.448,4.219 7.063,4.469 0.615,0.25 10 false *14 (*E) 6.313,5.167 6.625,5.365 0.313,0.198 10 false BE 6.885,5.167 7.042,5.365 0.156,0.198 10 false W 3.323,0.354 3.781,0.552 0.458,0.198 10 false *15 3.49,6.271 3.948,6.469 0.458,0.198 10 false *16 1.729,1.052 1.885,1.25 0.156,0.198 10 false W 1.188,1.052 1.344,1.25 0.156,0.198 10 false V 0.76,5.188 0.917,5.385 0.156,0.198 10 false R 1.26,5.188 1.417,5.385 0.156,0.198 10 false W
*A for Radio and Display Type *B for Navigation Receiver Type
*C w/ Smart Entry and Start System *D w/ Parking Assist Monitor System
*E w/ Toyota Parking Assist-sensor System - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 Steering Sensor
*3 Power Steering ECU Assembly *4 Airbag Sensor Assembly
*5 DLC3 *6 Combination Meter Assembly
*7 Radio and Display Receiver Assembly *8 Navigation Receiver Assembly
*9 ECM *10 Brake Actuator Assembly
*11 Air Conditioning Amplifier Assembly *12 Smart Key ECU Assembly (Certification ECU)
*13 Network Gateway ECU *14 Clearance Warning ECU Assembly
*15 CAN No. 1 Junction Connector *16 CAN No. 2 Junction Connector


C247959C02
2.417,0.438 2.76,0.708 0.344,0.271 10 false *a 3.375,3.958 3.594,4.198 0.219,0.24 10 false I94 3.375,3.417 3.594,3.656 0.219,0.24 10 false I96 3.323,3.677 3.615,3.917 0.292,0.24 10 false I100 3.375,2.573 3.667,2.813 0.292,0.24 10 false I95 3.375,2.854 3.594,3.094 0.219,0.24 10 false I97 3.323,3.146 3.615,3.385 0.292,0.24 10 false I103 3.375,4.24 3.667,4.479 0.292,0.24 10 false I93
*a Component without harness connected
(CAN No. 1 Junction Connector)
- -


Wiring Color:
CAN No. 1 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I93 B W
Combination meter assembly I94 R W
Power steering ECU assembly I100 G W
DLC3 I96 L W
Airbag sensor assembly I103 Y W
Steering sensor I97 V W
Main body ECU (multiplex network body ECU) I95 P W


C355210C01
2.323,0.448 2.635,0.646 0.313,0.198 10 false *a 3.573,2.313 4.188,2.51 0.615,0.198 10 false I101 3.573,2.563 4.188,2.76 0.615,0.198 10 false I102 3.573,2.854 4.188,3.052 0.615,0.198 10 false I104 3.583,3.125 4.198,3.323 0.615,0.198 10 false I106 3.573,3.385 4.188,3.583 0.615,0.198 10 false I177 3.583,3.667 4.198,3.865 0.615,0.198 10 false I161 3.583,3.958 4.198,4.156 0.615,0.198 10 false I107 3.583,4.26 4.198,4.458 0.615,0.198 10 false I105
*a Component without harness connected
(CAN No. 2 Junction Connector)
- -


Wiring Color:
CAN No. 2 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I101 B W
Air conditioning amplifier assembly I102 V W
ECM I104 P W
Smart key ECU assembly (certification ECU)*1 I106 L W
Clearance warning ECU assembly*2 I177 BE W
Network gateway ECU*3 I161 G W
·

Radio and display receiver assembly*4

·

Navigation receiver assembly*5


I107 R W
Brake actuator assembly I105 Y W


*1: w/ Smart Entry and Start System

*2: w/ Toyota Parking Assist-sensor System

*3: w/ Parking Assist Monitor System

*4: for Radio and Display Type

*5: for Navigation Receiver Type


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus lines.



Result:
Symptom Proceed to
The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) A
The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.) B


d.

When there is a short to GND in one or more of the bus lines that connect to an ECU or sensor:

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the electrical tester is normal (200 Ω or higher) to confirm that there is a short to GND in the one bus line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.





e.

When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:

i.

With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.




A

3.CHECK CAN NO. 1 JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
3.CHECK CAN NO. 1 JUNCTION CONNECTOR
a.
C247966C03
2.677,1.438 3.135,1.719 0.458,0.281 2.813,2.135 2.458,1.938 2.458,1.938 2.167,1.938 true 2.854,2.365 2.854,2.667 2.854,2.667 2.208,2.667 true 2.667,2.229 2.51,2.146 2.51,2.146 2.396,2.146 false 2.74,2.333 2.438,2.333 true 0.083,0.063 0.365,0.344 0.281,0.281 10 false *a 1.635,1.875 2.375,2.188 0.74,0.313 10 false CANH*b 1.667,2.594 2.26,2.813 0.594,0.219 10 false CANL*b 2.813,1.5 3.104,1.667 0.292,0.167 10 false I93 2.26,2.073 2.396,2.24 0.135,0.167 10 false B 2.281,2.271 2.448,2.438 0.167,0.167 10 false W
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector


Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C292403C42
1.458,0.167 1.885,0.406 0.427,0.24 0.917,0.333 1.115,0.333 1.115,0.333 1.594,0.781 true 1.615,1.917 1.823,1.917 1.823,1.917 2.042,1.5 true 2.406,0.302 2.188,0.302 2.188,0.302 2.042,0.781 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *1 1.563,0.198 1.875,0.396 0.313,0.198 10 false I39 2.49,0.219 3.104,0.417 0.615,0.198 10 false CANH 1.177,1.844 1.792,2.042 0.615,0.198 10 false CANL 0.635,0.271 1.021,0.51 0.385,0.24 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

4.CHECK CAN NO. 2 JUNCTION CONNECTOR

NG

REPLACE CAN NO. 1 JUNCTION CONNECTOR

4.CHECK CAN NO. 2 JUNCTION CONNECTOR
a.

Reconnect the I93 CAN main bus line connector to the CAN No. 1 junction connector.


b.
C355223C01
2.479,1.427 2.875,1.698 0.396,0.271 2.229,2.26 2.479,2.26 false 2.688,2.365 2.688,2.698 2.688,2.698 2.771,2.698 true 2.594,2.344 2.594,3.01 2.594,3.01 2.76,3.01 true 2.135,1.99 2.302,1.99 2.302,1.99 2.635,2.156 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 2.563,1.49 2.958,1.708 0.396,0.219 10 false I101 1.573,1.906 2.146,2.125 0.573,0.219 10 false CANH*b 2.833,2.635 3.354,2.854 0.521,0.219 10 false CANL*b 2.823,2.938 3.156,3.188 0.333,0.25 10 false W 2.073,2.188 2.406,2.438 0.333,0.25 10 false B
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector


Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C292403C42
1.458,0.167 1.885,0.406 0.427,0.24 0.917,0.333 1.115,0.333 1.115,0.333 1.594,0.781 true 1.615,1.917 1.823,1.917 1.823,1.917 2.042,1.5 true 2.406,0.302 2.188,0.302 2.188,0.302 2.042,0.781 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *1 1.563,0.198 1.875,0.396 0.313,0.198 10 false I39 2.49,0.219 3.104,0.417 0.615,0.198 10 false CANH 1.177,1.844 1.792,2.042 0.615,0.198 10 false CANL 0.635,0.271 1.021,0.51 0.385,0.24 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

REPLACE CAN NO. 2 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or higher when it was disconnected).


b.

Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C292403C42
1.458,0.167 1.885,0.406 0.427,0.24 0.917,0.333 1.115,0.333 1.115,0.333 1.594,0.781 true 1.615,1.917 1.823,1.917 1.823,1.917 2.042,1.5 true 2.406,0.302 2.188,0.302 2.188,0.302 2.042,0.781 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *1 1.563,0.198 1.875,0.396 0.313,0.198 10 false I39 2.49,0.219 3.104,0.417 0.615,0.198 10 false CANH 1.177,1.844 1.792,2.042 0.615,0.198 10 false CANL 0.635,0.271 1.021,0.51 0.385,0.24 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR