There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Brake actuator assembly ·
Steering sensor ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Smart key ECU assembly (certification ECU)*1 ·
Navigation receiver assembly*2 ·
Radio and display receiver assembly*3 ·
Network gateway ECU*4 ·
Clearance warning ECU assembly*5 ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector |
*1: w/ Smart Entry and Start System
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Parking Assist Monitor System
*5: w/ Toyota Parking Assist-sensor System
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to DLC3 |
Disconnect the I96 DLC3 branch line connector from the CAN No. 1 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I96 DLC3 branch line connector to the CAN No. 1 junction connector.
| *1 | DLC3 |
Disconnect the connectors from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.
Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
Using an electrical tester, measure the resistance between terminals 6 (CANH) and 16 (BAT), or between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.
| *A | for Radio and Display Type | *B | for Navigation Receiver Type |
| *C | w/ Smart Entry and Start System | *D | w/ Parking Assist Monitor System |
| *E | w/ Toyota Parking Assist-sensor System | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | Steering Sensor |
| *3 | Power Steering ECU Assembly | *4 | Airbag Sensor Assembly |
| *5 | DLC3 | *6 | Combination Meter Assembly |
| *7 | Radio and Display Receiver Assembly | *8 | Navigation Receiver Assembly |
| *9 | ECM | *10 | Brake Actuator Assembly |
| *11 | Air Conditioning Amplifier Assembly | *12 | Smart Key ECU Assembly (Certification ECU) |
| *13 | Network Gateway ECU | *14 | Clearance Warning ECU Assembly |
| *15 | CAN No. 1 Junction Connector | *16 | CAN No. 2 Junction Connector |
| *a | Component without harness connected
(CAN No. 1 Junction Connector) |
- | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |
| Combination meter assembly | I94 | R | W |
| Power steering ECU assembly | I100 | G | W |
| DLC3 | I96 | L | W |
| Airbag sensor assembly | I103 | Y | W |
| Steering sensor | I97 | V | W |
| Main body ECU (multiplex network body ECU) | I95 | P | W |
| *a | Component without harness connected
(CAN No. 2 Junction Connector) |
- | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Air conditioning amplifier assembly | I102 | V | W |
| ECM | I104 | P | W |
| Smart key ECU assembly (certification ECU)*1 | I106 | L | W |
| Clearance warning ECU assembly*2 | I177 | BE | W |
| Network gateway ECU*3 | I161 | G | W |
·
Radio and display receiver assembly*4 ·
Navigation receiver assembly*5 |
I107 | R | W |
| Brake actuator assembly | I105 | Y | W |
*1: w/ Smart Entry and Start System
*2: w/ Toyota Parking Assist-sensor System
*3: w/ Parking Assist Monitor System
*4: for Radio and Display Type
*5: for Navigation Receiver Type
Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.
| Symptom | Proceed to |
|---|---|
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) | A |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) | B |
When there is a short to +B in one or more of the bus lines that connect to an ECU or sensor:
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the electrical tester is normal (6 kΩ or higher) to confirm that there is a short to +B in the one bus line only.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
A
B
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
Disconnect the I93 CAN main bus line connector from the CAN No. 1 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I93 CAN main bus line connector to the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
Disconnect the I101 CAN main bus line connector from the CAN No. 2 junction connector.
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Result |
|---|
| OK |
| NG |
OK
NG