CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the A43 and I78 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| A43-11 (E) - Body ground | - | W - Body ground | Ground | Always | Below 1 Ω | - |
| A43-2 (+B) - A43-11 (E) | Input | W - W | +B power supply | Always | 11 to 14 V | - |
| I78-6 (IG1D) - Body ground | Output | P - Body ground | IG1 signal | 20°C (68°F) | 40.74 to 59.49 Ω | IG1 Relay Monitor(Outside) |
| A43-9 (IG2D) - Body ground | Output | R - Body ground | IG2 signal | 20°C (68°F) | Approximately 302.97 Ω | IG2 Relay Monitor(Outside) |
| I78-4 (ACCD) - Body ground | Output | W - Body ground | ACC signal | 20°C (68°F) | 81.49 to 118.98 Ω | ACC Relay Monitor |
| A43-10 (CUTB) - A43-11 (E) | Input | L - W | Dark current cut pin* | Always | 11 to 14 V | - |
*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).
If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.
Reconnect the A43 and I78 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| I78-5 (IG) - A43-11 (E) | Input | LG - W | IG power supply | Engine switch off → on (IG) | Below 1 V → 11 to 14 V | Engine Switch |
| I78-12 (CLG1) - A43-11 (E) | Output | Y - W | Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area*1 6.
All doors locked through wireless operation |
Pulse generation (See waveform 1) | Over Head + Driver Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Driver Side (key diagnostic mode) | ||||
| I78-13 (CG1B) - A43-11 (E) | Output | LG - W | Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Driver Side (key diagnostic mode) |
| I78-11 (CLG2) - A43-11 (E) | Output | Y - W | Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area*1 6.
All doors locked through wireless operation |
Pulse generation (See waveform 1) | Over Head + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Passenger Side (key diagnostic mode) | ||||
| I78-10 (CG2B) - A43-11 (E) | Output | L*4, LG*5 - W | Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Passenger Side (key diagnostic mode) |
| I78-3 (CLG5) - A43-11 (E) | Output | R - W | Output to No. 1 indoor electrical key antenna assembly (front floor) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Front Room (key diagnostic mode) |
| I78-2 (CG5B) - A43-11 (E) | Output | W - W | Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Front Room (key diagnostic mode) |
| I78-20 (TSW1) - A43-11 (E) | Input | R - W | Driver door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded. |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
Pulse generation (See waveform 6) | D-Door Trigger Switch |
| I78-8 (TSW2) - A43-11 (E) | Input | V - W | Front passenger door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded. |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Front passenger door lock sensor not touched → touched |
Pulse generation (See waveform 6) | P-Door Trigger Switch |
| I78-22 (SEN1) - A43-11 (E) | Input | LG - W | Driver door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Driver door unlock sensor not touched → touched |
Pulse generation (See waveform 6) | D-Door Touch Sensor |
| I78-23 (SEN2) - A43-11 (E) | Input | GR - W | Front passenger door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Front passenger door unlock sensor not touched → touched |
Pulse generation (See waveform 6) | P-Door Touch Sensor |
| O1-27 (TSW5) - A43-11 (E) | Input | G - W | Luggage door opening switch assembly signal input | Luggage door opening switch assembly off → on | Pulse generation (See waveform 6) | Tr/B-Door Unlock SW |
| O1-11 (CLG6) - A43-11 (E) | Output | W - W | Output to No. 2 indoor electrical key antenna assembly (rear floor) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Rear Room (key diagnostic mode) |
| O1-10 (CG6B) - A43-11 (E) | Output | B - W | Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) | Proceed:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Rear Room (key diagnostic mode) |
| O1-9 (CLG7) - A43-11 (E) | Output | R - W | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) | Proceed:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
Pulse generation (See waveform 4) | Over Head + Luggage (inside) (key diagnostic mode) |
| O1-8 (CG7B) - A43-11 (E) | Output | W - W | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) | Proceed:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
Pulse generation (See waveform 4) | Over Head + Luggage (inside) (key diagnostic mode) |
| I78-19 (POS1) - A43-11 (E) | Output | P*4, B*5 - W | Driver door unlock sensor power source (12 V (drops when engine switch turned on (IG))) | Engine switch off → on (IG) | 9 to 14 V → Below 2 V | - |
| I78-21 (POS2) - A43-11 (E) | Output | B*4, P*5 - W | Front passenger door unlock sensor power source (12 V (drops when engine switch turned on (IG))) | Engine switch off → on (IG) | 9 to 14 V → Below 2 V | - |
| O1-5 (RCO) - A43-11 (E) | Output | G - W | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 7) | - |
| O1-17 (RDAM) - A43-11 (E) | Input | Y - W | Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). | Proceed:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 8) | - |
| O1-6 (CSEL) - A43-11 (E) | Output | LG - W | Communication channel switching circuit. | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation | Key diagnostic mode |
| O1-7 (ASEL) - A43-11 (E)*6 | Output | L - W | Wireless charging system stop signal | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly inside vehicle 3.
Engine switch on (ACC) |
Below 1 V → 4.5 to 6 V
(One second after power switch on (ACC)) |
- |
| O1-2 (CLG8) - A43-11 (E) | Output | V - W | Output to electrical key antenna (outside luggage) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage door opening switch assembly off → on |
Pulse generation (See waveform 5) | Over Head + Luggage
or Luggage + Luggage (key diagnostic mode) |
| O1-1 (CG8B) - A43-11 (E) | Output | P - W | Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage door opening switch assembly off → on |
Pulse generation (See waveform 5) | Over Head + Luggage
or Luggage + Luggage (key diagnostic mode) |
*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).
*4: for LHD
*5: for RHD
*6: w/ Wireless Charging System
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I78-12 (CLG1) - A43-11 (E)
I78-11 (CLG2) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area* 6.
All doors locked through wireless operation |
*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I78-12 (CLG1) - A43-11 (E)
I78-11 (CLG2) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area* 6.
All doors locked through wireless operation |
*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
| Item | Content |
|---|---|
| Tester Connection | I78-13 (CG1B) - A43-11 (E)
I78-10 (CG2B) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
All doors locked through wireless operation |
| *a | Door open |
| *b | After approximately 30 seconds from when the door is closed |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I78-3 (CLG5) - A43-11 (E)
I78-2 (CG5B) - A43-11 (E) O1-11 (CLG6) - A43-11 (E) O1-10 (CG6B) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
| *a | Before driver door lock sensor touched |
| *b | After driver door lock sensor touched |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | O1-9 (CLG7) - A43-11 (E)
O1-8 (CG7B) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Proceed:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
| *a | Engine switch off, all doors closed and luggage door opening switch assembly off → on |
Using an oscilloscope, check waveform 5.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | O1-2 (CLG8) - A43-11 (E)
O1-1 (CG8B) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage door opening switch assembly off → on |
| *a | In actuality, sampling is being performed |
Using an oscilloscope, check waveform 6.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I78-20 (TSW1) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | I78-8 (TSW2) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Front passenger door lock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | I78-22 (SEN1) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Driver door unlock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | I78-23 (SEN2) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Front passenger door unlock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | O1-27 (TSW5) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Luggage door opening switch assembly off → on |
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 7.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | O1-5 (RCO) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 8.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | O1-17 (RDAM) - A43-11 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Proceed:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 2 connectors |
| *A | Main body ECU (multiplex network body ECU) with 3 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 3 connectors |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω | - |
| I12-3 (GND2) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| MB-30 (BECU) - Body ground | Input | - | Battery power supply (for CPU) | Always | 11 to 14 V | - |
| MB-31 (ALTB) - Body ground | Input | - | Battery power supply (for indicator) | Always | 11 to 14 V | - |
| MB-29 (ACC) - Body ground | Input | - | ACC power supply | Engine switch on (ACC) | 11 to 14 V | ACC SW |
| MB-32 (IG) - Body ground | Input | - | Engine switch power supply | Engine switch on (IG) | 11 to 14 V | IG SW |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| 3C-15 (FLCY) - Body ground | Input | L - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V | FL Door Courtesy |
| Front door LH closed | 11 to 14 V | |||||
| I13-19 (FRCY) - Body ground | Input | Y - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V | FR Door Courtesy |
| Front door RH closed | 11 to 14 V | |||||
| I13-1 (LCTY) - Body ground | Input | LG - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V | RL Door Courtesy SW |
| Rear door LH closed | Pulse generation (See waveform 1 or 2) | |||||
| I13-6 (RCTY) - Body ground | Input | B - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V | RR Door Courtesy SW |
| Rear door RH closed | Pulse generation (See waveform 1 or 2) | |||||
| 3C-9 (LGCY) - Body ground | Input | W - Body ground | Luggage door courtesy light switch input | Luggage compartment door open | Below 1 V | Luggage Courtesy SW |
| Engine switch off, all doors closed and luggage compartment door closed | 11 to 14 V | |||||
| I13-11 (L2) - Body ground | Input | R - Body ground | Driver door key-linked lock input | Driver door key cylinder in lock position | Below 1 V | Door Key SW-Lock |
| Engine switch off, all doors closed and driver door key cylinder in neutral position | Pulse generation (See waveform 1 or 2) | |||||
| I13-24 (UL3) - Body ground | Input | GR*1, Y*2 - Body ground | Driver door key-linked unlock input | Driver door key cylinder in unlock position | Below 1 V | D Door Key SW-UL |
| Engine switch off, all doors closed and driver door key cylinder in neutral position | Pulse generation (See waveform 1 or 2) | |||||
| 3B-3 (ACT+) - Body ground | Output | W - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3B-2 (ACT+) - Body ground | Output | B - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3B-1 (ACT+) - Body ground | Output | L - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3C-12 (ACT+) - Body ground | Output | L - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3B-4 (ACTD) - Body ground | Output | GR*1, V*2 - Body ground | Driver door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3C-10 (TR+) - Body ground | Output | R - Body ground | Driver door lock motor unlock drive output | Luggage door open button of electrical key transmitter sub-assembly not pressed | Below 1 V | - |
| Luggage door open button of electrical key transmitter sub-assembly pressed | 11 to 14 V | |||||
| 3B-8 (ACT-) - Body ground | Output | V*1, GR*2 - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3C-11 (ACT-) - Body ground | Output | G - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3B-9 (ACT-) - Body ground | Output | B - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| I13-7 (LSFL) - Body ground | Input | V - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V | FL Door Lock Pos |
| Engine switch off, all doors closed and front door LH locked | Pulse generation (See waveform 1 or 2) | |||||
| I13-18 (LSFR) - Body ground | Input | W - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V | FR Door Lock Pos |
| Engine switch off, all doors closed and front door RH locked | Pulse generation (See waveform 1 or 2) | |||||
| 3C-17 (LSR) - Body ground | Input | LG - Body ground | Rear door LH unlock detection switch input | Rear door LH or RH unlocked | Below 1 V | RL-Door Lock Pos SW |
| Engine switch off, all doors closed and rear door LH and RH locked | Pulse generation (See waveform 3 or 4) | |||||
| 3A-53 (LSR) - Body ground | Input | Y - Body ground | Rear door RH unlock detection switch input | Rear door RH or LH unlocked | Below 1 V | RR-Door Lock Pos SW |
| Engine switch off, all doors closed and rear door RH and LH locked | Pulse generation (See waveform 3 or 4) |
*1: for LHD
*2: for RHD
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I13-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | I13-1 (LCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door LH closed |
| Item | Content |
|---|---|
| Tester Connection | I13-6 (RCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door RH closed |
| Item | Content |
|---|---|
| Tester Connection | I13-24 (UL3) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | I13-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and front door LH locked |
| Item | Content |
|---|---|
| Tester Connection | I13-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | I13-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | I13-1 (LCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door LH closed |
| Item | Content |
|---|---|
| Tester Connection | I13-6 (RCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door RH closed |
| Item | Content |
|---|---|
| Tester Connection | I13-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and front door LH locked |
| Item | Content |
|---|---|
| Tester Connection | I13-24 (UL3) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | I13-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | 3C-17 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and rear door LH and RH locked |
| Item | Content |
|---|---|
| Tester Connection | 3A-53 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and rear door RH and LH locked |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | 3C-17 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and rear door LH and RH locked |
| Item | Content |
|---|---|
| Tester Connection | 3A-53 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and rear door RH and LH locked |