Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM19V0EQ _53 Suspension _052591 TIRE PRESSURE MONITORING _0265587 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light illuminates and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C354516E05
5.24,1.896 6.615,2.385 1.375,0.49 10 false Tire Pressure Warning ECU and Receiver 5.458,1.01 6.833,1.5 1.375,0.49 10 false CLSW 1.865,1.438 4.573,1.646 2.708,0.208 10 false Tire Pressure Warning Reset Switch 1.875,1.26 3.25,1.75 1.375,0.49 10 false I197 2.313,0.896 2.583,1.229 0.271,0.333 10 false 6 3.417,0.885 3.688,1.219 0.271,0.333 10 false 9 2.49,0.896 2.76,1.229 0.271,0.333 10 false E 3.115,0.906 3.385,1.24 0.271,0.333 10 false INT 5.271,0.896 5.542,1.229 0.271,0.333 10 false 3 5.25,1.719 6.625,2.208 1.375,0.49 10 false N44

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.
C355093C01
1.177,1.865 1.51,1.448 false 2.438,1.865 2.104,1.448 false 1.083,1.885 1.583,2.083 0.5,0.198 10 false INT 2.417,1.885 2.573,2.083 0.156,0.198 10 false E 0.125,0.146 0.625,0.344 0.5,0.198 10 false *a
*a Component without harness connected
(Tire Pressure Warning Reset Switch)


Remove the tire pressure warning reset switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (INT) - 6 (E) Tire pressure warning reset switch is pushed Below 1 Ω
Tire pressure warning reset switch is not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the I197 tire pressure warning reset switch connector.


b.

Disconnect the N44 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N44-3 (CLSW) - I197-9 (INT) Always Below 1 Ω
N44-3 (CLSW) or I197-9 (INT) - Body ground Always 10 kΩ or higher
I197-6 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR