Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM19V0EQ _53 Suspension _052591 TIRE PRESSURE MONITORING _0265587 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C250865C94
0.313,1.042 0.698,1.281 0.385,0.24 0.375,1.073 0.677,1.281 0.302,0.208 10 false N44 0.146,0.083 0.354,0.271 0.208,0.188 10 false *a
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the N44 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N44-1 (IG) - N44-12 (GND) V - BR IG power source Ignition switch ON 10 to 16 V
N44-7 (+B) - N44-12 (GND)* SB - BR Power supply (from battery) Always 10 to 16 V
N44-12 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

*: w/o Smart Entry and Start System


b.

Connect the N44 tire pressure warning ECU and receiver connector.


c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


E129452C38
2,0.802 2.323,1 0.323,0.198 0.115,0.094 0.438,0.344 0.323,0.25 10 false *a 2.042,0.823 2.333,1.01 0.292,0.188 10 false N44
*a Component without harness connected
(Tire Pressure Warning ECU and Receiver)
- -


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N44-3 (CLSW) - N44-12 (GND) W - BR Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch on


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch off


8 to 15 V
N44-4 (RDA2) - N44-12 (GND) L - BR Output signals Ignition switch ON Pulse generation (see waveform 1)
N44-5 (PRG2) - N44-12 (GND) P - BR Input signals Ignition switch ON Pulse generation (see waveform 1)
N44-9 (PRG3) - N44-12 (GND)* GR - BR Output signals Ignition switch ON → Ignition switch off 0 V → 16 V
N44-10 (RDA3) - N44-12 (GND)* G - BR Input signals Ignition switch ON → Ignition switch off 0 V → 16 V

*: w/o Smart Entry and Start System


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal N44-4 (RDA2) - N44-12 (GND)
N44-5 (PRG2) - N44-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.