Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

C240763E29
2.531,1.115 2.323,0.781 2.323,0.781 2.115,0.781 false 4.469,1.115 4.656,0.729 4.656,0.729 4.917,0.729 false 6.354,2.656 6.833,2.896 0.479,0.24 10 false ECM 3.708,3.781 4.073,4.031 0.365,0.25 10 false A49 4.021,3.781 5.729,4.146 1.708,0.365 10 false Brake Actuator Assembly 2.708,0.417 3.198,0.677 0.49,0.26 10 false DLC3 1.49,5 3.656,5.292 2.167,0.292 10 false : CAN Main Bus Line (CANH) 4.458,5 6.438,5.292 1.979,0.292 10 false : CAN Branch Line (CANH) 4.448,5.396 6.365,5.698 1.917,0.302 10 false : CAN Branch Line (CANL) 1.469,5.406 3.479,5.677 2.01,0.271 10 false : CAN Main Bus Line (CANL) 2.865,3.469 3.99,3.729 1.125,0.26 10 false ECU-IG1 NO. 1 4.031,4.615 5.104,4.865 1.073,0.25 10 false Trouble Area 4,3.313 4.375,3.573 0.375,0.26 10 false IG1 4.958,3.313 5.469,3.573 0.51,0.26 10 false GND1 4.229,3.063 4.677,3.271 0.448,0.208 10 false CANH 4.729,3.063 5.146,3.292 0.417,0.229 10 false CANL 3.75,3.198 4,3.406 0.25,0.208 10 false 28 5.406,3.177 5.667,3.396 0.26,0.219 10 false 38 4.25,2.833 4.563,3.052 0.313,0.219 10 false 26 4.906,2.833 5.177,3.083 0.271,0.25 10 false 14 0.177,0.667 2.24,0.917 2.063,0.25 10 false CAN No. 1 Junction Connector 4.979,0.646 7.031,0.885 2.052,0.24 10 false CAN No. 2 Junction Connector 0.469,2.656 1.635,3.083 1.167,0.427 10 false Combination Meter Assembly 0.865,2.042 1.365,2.292 0.5,0.25 10 false 120 Ω 6.146,2.031 6.719,2.281 0.573,0.25 10 false 120 Ω 0.083,0.115 1.521,0.406 1.438,0.292 12 false V Bus (for LHD): 0.208,2.667 0.594,2.927 0.385,0.26 10 false I18 6.031,2.646 6.365,2.833 0.333,0.188 10 false A25

C241447E15
2.354,1.156 2.208,0.813 2.208,0.813 2.073,0.813 false 4.417,1.156 4.604,0.781 4.604,0.781 4.854,0.781 false 0.854,2.719 1.354,2.948 0.5,0.229 10 false ECM 3.24,4.094 3.635,4.365 0.396,0.271 10 false A49 3.563,4.094 5.323,4.417 1.76,0.323 10 false Brake Actuator Assembly 2.99,0.438 3.5,0.75 0.51,0.313 10 false DLC3 1.469,5 3.521,5.323 2.052,0.323 10 false : CAN Main Bus Line (CANH) 4.458,5 6.198,5.354 1.74,0.354 10 false : CAN Branch Line (CANH) 4.458,5.406 6.354,5.729 1.896,0.323 10 false : CAN Branch Line (CANL) 1.469,5.417 3.563,5.719 2.094,0.302 10 false : CAN Main Bus Line (CANL) 2.385,3.76 3.542,4.01 1.156,0.25 10 false ECU-IG1 NO. 1 1.396,3.938 2.365,4.24 0.969,0.302 10 false Trouble Area 3.521,3.563 3.896,3.792 0.375,0.229 10 false IG1 4.469,3.563 4.938,3.802 0.469,0.24 10 false GND1 3.75,3.292 4.208,3.49 0.458,0.198 10 false CANH 4.271,3.292 4.75,3.5 0.479,0.208 10 false CANL 3.26,3.458 3.552,3.698 0.292,0.24 10 false 28 4.938,3.458 5.24,3.708 0.302,0.25 10 false 38 3.76,3.052 4.094,3.385 0.333,0.333 10 false 26 4.417,3.063 4.75,3.302 0.333,0.24 10 false 14 0.125,0.719 2.208,1.01 2.083,0.292 10 false CAN No. 1 Junction Connector 4.917,0.688 6.927,0.875 2.01,0.188 10 false CAN No. 2 Junction Connector 5.802,2.688 7,3.208 1.198,0.521 10 false Combination Meter Assembly 0.677,2.094 1.24,2.344 0.563,0.25 10 false 120 Ω 6.156,2.083 6.698,2.333 0.542,0.25 10 false 120 Ω 0.104,0.125 1.646,0.448 1.542,0.323 12 false V Bus (for RHD): 0.531,2.719 0.927,2.969 0.396,0.25 10 false A25 5.542,2.688 5.854,2.906 0.313,0.219 10 false I18

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 13 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:

DTC C1241 is not output.


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
OK (DTC C1241 is not output) A
NG (DTC C1241 is output) B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURES INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A49 brake actuator assembly connector.


c.
C238832C09
1.479,0.094 1.958,0.385 0.479,0.292 0.927,1.521 0.927,0.76 0.927,0.76 1.198,0.76 false 1,1.802 1,2.438 1,2.438 1.177,2.438 false 0.208,0.115 0.406,0.271 0.198,0.156 10 false *a 1.573,0.156 1.865,0.313 0.292,0.156 10 false A49 1.302,0.677 1.813,0.885 0.51,0.208 10 false CANH 1.25,2.365 1.76,2.573 0.51,0.208 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-26 (CANH) - A49-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result::
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)