BODY STRUCTURE > DETAILS



FUNCTION
  1. Safety Features

    1. Impact Absorbing Structure for Frontal Collision

      1. Through the adoption of a body structure that disperses collision energy to multiple frame components, collision energy is efficiently absorbed to suppress cabin deformation.
      2. The front side members utilize to absorb and disperse energy in a frontal collision.

      3. Door beltline reinforcements are strengthened to optimize dispersal of collision energy to the rocker panel and floor panel.


        Y112040E01


        Text in Illustration 
        *1
        Front Side Member
        *2
        Beltline Reinforcement
        V100136
        Impact
        V100135
        Impact Flow

    2. Impact Absorbing Structure for Side Collision

      1. Through the adoption of a body structure that disperses collision energy to multiple frame components, collision energy is efficiently absorbed to suppress cabin deformation.
      2. The center pillars are strengthened to optimize dispersal of collision energy to the rocker panel and roof reinforcement.
      3. The use of roof reinforcement and floor crossmember enables a construction that transmits load to the opposite side of the vehicle in a collision.

      4. Optimal placement of the impact protect beams enables a construction that efficiently transmits load.


        Y112045E01


        Text in Illustration 
        *1
        Center Pillar Outer Reinforcement
        *2
        Front Floor Crossmember
        *3
        Center Floor Crossmember
        *4
        Roof Reinforcement
        *5
        Rocker Panel Reinforcement
        *6
        Impact Protect Beam
        V100135
        Impact Flow
        -
        -

      5. When the roof is subjected to an impact, the impact is dispersed to the roof reinforcements, front pillars and center pillars, thereby minimizing deformation of the cabin.


        Y112046E01


        Text in Illustration 
        *1
        Roof Reinforcement
        *2
        Front Pillar
        *3
        Center Pillar
        -
        -
        V100136
        Impact
        V100135
        Impact Flow

    3. Impact Absorbing Structure for Rear Collision

      1. Straight rear side members are used to reduce body deformation in a rear collision.

    4. Lessening Pedestrian Injury


      1. A hood reinforcement is provided for the hood inner panel to help secure excellent pedestrian protection performance and tensile rigidity.


        Y112048E01


        Text in Illustration 
        *1
        Longitudinal Ribbed Structure
        *2
        Dent Reinforcement (Impact Absorbing Structure)

      2. An impact absorbing bracket is used for the mounting portion of the front fender panel to absorb impact energy to the head of the pedestrian in a collision, thus dampening the impact to the head.


        Y112050E01


        Text in Illustration 
        *1
        Impact Absorbing Bracket (Front)
        *2
        Impact Absorbing Bracket (Rear)
        *a
        A-A Cross Section
        *b
        B-B Cross Section
        *c
        Before Collision
        *d
        After Collision
        V100136
        Impact
        -
        -

      3. The cowl uses an open section structure that collapses easily in an impact from the top, thus reducing the impact to and head injuries sustained by a pedestrian in an accident.


        Y112049E01


        Text in Illustration 
        *1
        Window Shield Glass
        *2
        Cowl Top Panel Sub-assembly
        *a
        A-A Cross Section
        *b
        Before Collision
        *c
        After Collision
        -
        -
        V100136
        Impact
        -
        -



  2. Aerodynamics



    1. An aero stabilizing fin is provided on the outer rear view mirror base for enhanced aerodynamics.

      1. After passing the aero stabilizing fin, the air speed will increase and vortex flow will be generated.
      2. This vortex flow increases the speed of surrounding air while at the same time pulling the airflow towards the vehicle body.
      3. The airflow with higher speed passes near both sides of the vehicle body and ends at the rear of the vehicle. This helps to hold the vehicle body, and thus stabilizes the vehicle.

      Y112064E01


      Text in Illustration 
      *a
      Aero Stabilizing Fin
      *b
      Vortex
      V100135
      Airflow
      V100136
      Hold the Vehicle from Both Side



    2. The height, angle, and shape of the front bumper have been optimized, resulting in smooth airflow underneath the floor.


      Y112060E01


      Text in Illustration 
      *1
      Front Bumper
      -
      -
      V100135
      Airflow
      -
      -

    3. Various types of airflow routing parts are provided under the floor to control airflow. In addition, an undercover is provided to make the under floor area flat in order to ensure excellent aerodynamic performance.



    4. A fin-shaped engine under cover and rear under cover have been adopted to achieve higher diffuser efficiency, thereby ensuring stability.


      Y112042


      Text in Illustration 
      V100144
      Undercover Area
      -
      -


CONSTRUCTION


  1. Lightweight and Highly Rigid Body



    1. High strength steel and ultra high strength steel are used in order to realize excellent body rigidity and a lightweight body.


      Y112057E01


      Text in Illustration 
      *1
      High Strength Steel
      *2
      Ultra High Strength Steel



  2. Rust-resistance Body



    1. Anti-corrosion steel sheet is used as shown in the following illustration:


      Y112061


      Text in Illustration (Upper Body:) 
      V100144
      Anti-corrosion Sheet Steel
      -
      -



    2. For rust resistance, sealant has been applied to the floor panel to prevent water from entering through the mating surfaces of the panels. Undercoating has been also applied to reduce damage to the body from chipping, contributing to rust resistance.


      Y112062E01


      Text in Illustration (Under Body:) 
      *a
      Sealant
      -
      -
      V100144
      Under Coat
      -
      -



  3. Body Shell Construction



    1. The cowl top panel sub-assembly outer is used to connect the left and right front spring supports, which is straight, improving lateral rigidity and ensuring front suspension input point rigidity and body rigidity.


      Y112055E01


      Text in Illustration 
      *1
      Cowl Top Panel Sub-assembly
      -
      -



    2. A closed shape has been adopted for the upper back panel. The upper back panel is used to connect the left and right back side panels, which is straight, improving light weight yet body rigidity.


      Y112056E01


      Text in Illustration 
      *1
      Under Back Panel
      -
      -



    3. Along with the optimal positioning of frame components such as rear side members ,center floor crossmember, rear floor crossmember and rear sub-frame, the usage of a small number of parts has realized a lightweight design while also ensuring an excellent rigidity and handling stability.


      Y112041E01


      Text in Illustration 
      *1
      Rear Side Member
      *2
      Center Floor Crossmember
      *3
      Rear Floor Crossmember
      *4
      Rear Sub-frame



  4. Low Vibration and Low Noise Body



    1. The following body structures are used, in order to reduce panel vibration and body frame movement.

      Panel vibration reduction structure
      1. The cross member of the dash panel is provided
      2. The tunnel reinforcement is connected to the floor


      Y112043E02


      Text in Illustration 
      *1
      Cross Member of Dash Panel
      *2
      Tunnel Reinforcement
      *3
      Floor Pan Panel
      -
      -

    2. Damping coatings are provided, combining enhanced quietness and reduced weight. (*A)



    3. Asphalt Sheets are applied to the floor in order to noise in the cabin. (*B)


      Y112851E01


      Text in Illustration 
      *A
      Models Produced by TOYOTA Motor Corporation
      *B
      Models Produced by TOYOTA Manufacturing, Russia, (TMMR) Inc.
      V100144
      Damping Material Area
      V102143
      Asphalt Sheet



    4. Silencer pads are provided on the engine compartment side and cabin side of the dash panel, minimizing penetration of engine noise and road noise into the cabin.


      Y112044E01


      Text in Illustration 
      *1
      Dash Panel Insulator Outer
      *2
      Dash Panel
      *3
      Dash Panel Insulator Inner
      -
      -



    5. The layout of the sound-absorbing material is optimized to reduce noise and vibration.


      Y112054E01


      Text in Illustration 
      *a
      A-A Cross Section
      *b
      B-B Cross Section
      *c
      C-C Cross Section
      -
      -
      V102143
      Sound-absorbing Material
      -
      -



    6. Silencers are provided inside the rear wheel housings to minimize the penetration into the cabin of splashing noise generated in the wheel housings.


      Y112053E01


      Text in Illustration 
      *1
      Rear Wheel House Silencer
      -
      -
      *a
      A-A Cross Section
      -
      -



    7. Weatherstrips are provided for the front and rear doors at the rocker panel to minimize the penetration of road noise into the cabin.


      Y112052E01


      Text in Illustration 
      *1
      Weatherstrip
      -
      -
      *a
      A-A Cross Section
      -
      -



  5. Parts with Low Repair Cost



    1. A concave design has been adopted for the front bumper absorber. This helps prevent the vehicle from going under obstacles in the event of a collision.


      Y112047E01


      Text in Illustration 
      *1
      Front Bumper Absorber
      *2
      Front Bumper Reinforcement
      *3
      Obstacles
      -
      -
      *a
      Before Collision
      *b
      After Collision