METER / GAUGE SYSTEM > DETAILS



OPERATING CONDITION
  1. Eco Driving Indicator Light Operation

    1. Eco Driving Indicator Light can operate when all of the following conditions are met:

      1. The ignition switch is ON and the engine is running.
      2. The vehicle is being driven with the shift lever in D.
      3. Temporary S mode is not selected.
      4. The vehicle is at a speed of 130 km/h (81 mph) or below.


FUNCTION
  1. Combination Meter Assembly

    1. Buzzer Function

      1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

      1
      Seat Belt Warning (Level 2)
      2
      Seat Belt Warning (Level 1)
      3
      EPS Warning
      4
      Smart Entry and Start System Warning 1 (Continuous)*1
      5
      Smart Entry and Start System Warning 2 (Intermittent)*1
      6
      Key Reminder Indicating Buzzer
      7
      Smart Entry and Start System Warning 2 (Continuous, 9 times at the maximum)*1
      8
      Smart Entry and Start System Warning (Once)*1
      9
      Multi-information Display Warning*2
      10
      Immobiliser Certification Reminder
      11
      Parking Brake Engaged Warning
      12
      Door Open while Driving Warning
      13
      S Mode Operation Reject Warning
      14
      Sliding Roof Open Warning*3
      15
      Turn Signal/Hazard Warning Operation
      -
      -
      1. *1: Models with smart entry and start system
      2. *2: Models with multi-information display
      3. *3: Models with sliding roof system



  2. LCD



    1. Display Flow Function

      1. The fuel gauge side LCD display changes in the following order due to ODO/TRIP switch operation.

      Y111666E01


      Text in Illustration 
      *A
      Models without Multi-information Display
      *B
      Models with Multi-information Display
      *1
      Odometer
      *2
      Trip Meter A
      *3
      Trip Meter B
      *4
      Average Fuel Consumption
      *5
      Eco Driving Indicator Light ON/OFF Mode
      -
      -
      V100136
      ODO/TRIP switch pressed briefly.
      V100135
      ODO/TRIP switch pressed and held.



  3. Multi-information Display

    1. Display Flow Function


      1. The multi-information display flow can be switched as shown in the flow chart below:


        Y111604E01


        No.
        Transition Condition
        *1
        Conditions are not met and all new messages have been displayed.
        *2
        If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each.
        *3
        If the ignition switch is turned to OFF during the "Opening" display, the "Opening" display will be shown from the beginning.
        *4
        If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met.
        *5
        If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed.



    2. Cruise Information Mode Function

      1. The cruise information is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.

      Y111669E01


      Text in Illustration 
      *1
      DISP Switch
      -
      -
      V100136
      DISP switch pressed briefly.
      -
      -
      1. The cruise information mode items displayed are as follows:

      No.
      Information
      Outline
      (1)
      Cruising Range
      1. Displays a value that has been calculated by the combination meter assembly. When the ignition switch is turned to ON, the combination meter assembly calculates the range based on continuously monitoring and storing information on fuel consumption data, and the residual fuel volume.
      2. This display is updated every 10 seconds.
      Average Fuel Consumption
      1. Displays a value that has been calculated by the combination meter assembly based on the distance driven and the fuel consumption volume (fuel injection signal from the ECM).
      2. This display is updated every 10 seconds.
      (2)
      Average Speed
      1. Displays the average vehicle speed calculated by the combination meter assembly based on the engine start signal and vehicle speed signal.
      2. This display is updated every 10 seconds.
      Elapsed Time
      Displays the length of time since the engine was started.
      (3)
      Eco Drive Level Display
      1. Displays the average fuel consumption calculated since the engine was started. Uses 4 different height bars to display the level.
      2. This display is updated every 10 seconds.
      (4)
      Settings
      Customizes the combination meter assembly language display and Eco Driving Indicator Light and instantaneous fuel consumption gauge deactivated or activated display states.
      (5)
      Blank Screen
      -

    3. Eco Drive Level

      1. The eco drive level changes among 4 levels to indicate the average fuel consumption.
      2. After the ignition switch is turned off, the eco drive level display appears for 3 seconds in the multi-information display. When the average fuel consumption is 7.8 L/100 km or less*1 or 8.8 L/100 km or less*2, the "EXCELLENT!" message flashes.
      1. *1: Models with 2AR-FE engine
      2. *2: Models with 2GR-FE engine

      Average Fuel Consumption Level (L/100 km)
      Multi-information Display
      Level 0 (15 or more)
      Y111606
      Level 1 (13 to 15)
      Y111607
      Level 2 (11 to 13)
      Y111608
      Level 3 (9 to 11)
      Y111668
      Level 4 (9 or less)
      When driving
      Y111609
      After ignition switch is turned off
      Y111610



    4. Customization Function

      1. In the settings screen of cruise information mode, pressing and holding the DISP switch enters setting mode.
      2. Press the DISP switch briefly to select the item to be customized. Press and hold the DISP switch to confirm the selection.

      Y111611E01


      Text in Illustration 
      *a
      Language Setting
      *b
      Eco Driving Indicator Light ON/OFF Setting
      V100136
      DISP switch pressed briefly.
      V100135
      DISP switch pressed and held.
      V100137
      If the vehicle has reached a speed of 8 km/h (5 mph)
      -
      -
      1. In setting mode, the following items of the combination meter assembly can be customized.

      Item
      Available Setting
      Language
      1. English
      2. French*1
      3. Spanish*1
      4. Russian*2
      Eco Driving Indicator Light and Instantaneous Fuel Consumption Gauge
      1. On
      2. Off
      1. *1: Except models for Russia
      2. *2: Models for Russia

    5. Warning Mode Function

      1. When a warning is necessary, the warning display interrupts the display in the multi-information display.
      2. The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.

      Priority
      Indication/Warning
      Master Warning Light
      Buzzer
      1
      Door Open (While Driving)*1
      Blinks
      Sounds
      Door Open
      -
      -
      Clearance Sonar Obstruction Detection*2
      -
      -
      CHECK SONAR*2
      Illuminates
      Sounds
      CLEAN SONAR*2
      Illuminates
      Sounds
      2
      AUTO POWER OFF TO CONSERVE BATTERY
      -
      -
      3
      SHIFT TO P POSITION*3
      Blinks
      Sounds
      4
      RELEASE PARKING BRAKE
      Blinks
      Sounds
      KEY NOT DETECTED*3
      Blinks
      Sounds
      5
      CHECK ENTRY & START SYSTEM*3
      Blinks
      Sounds
      6
      CHECK CRUISE CONTROL SYSTEM*4
      Illuminates
      Sounds
      7
      TURN POWER OFF*3
      Blinks
      Sounds
      KEY DETECTED IN VEHICLE*3
      Blinks
      Sounds
      TURN LIGHTS OFF
      Blinks
      Sounds
      MOONROOF OPEN*5
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH TO START*3
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START*3
      Blinks
      Sounds
      SHIFT TO P POSITION TO START*3
      Blinks
      Sounds
      8
      STEERING LOCK ACTIVE
      Blinks
      Sounds
      9
      KEY BATTERY LOW*3
      Illuminates
      Sounds
      10
      POWER ON*3
      -
      -
      Engine start ready state*3
      -
      -
      1. *1: If the vehicle has reached a speed of 5 km/h (3 mph).
      2. *2: Models with Toyota parking assist-sensor system
      3. *3: Models with smart entry and start system
      4. *4: Models with cruise control system
      5. *5: Models with sliding roof system