WINDSHIELD GLASS > INSTALLATION |
| 1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with Primer G.
Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Ceramic Notch | - | - |
| *a | Windshield Glass Edge Side | - | - |
| Area | Dimension |
| a | 13.7 to 14.7 mm (0.539 to 0.578 in.) |
| 2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
| 3. INSTALL WINDSHIELD GLASS RETAINER |
Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.
![]() |
Install the 2 windshield glass retainers onto the windshield glass as shown in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch |
| 4. INSTALL WINDSHIELD OUTSIDE MOULDING |
Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.
![]() |
Install the windshield outside moulding onto the windshield glass as shown in the illustration.
| *A | Back Side |
| Area | Dimension |
| a | 6.7 mm (0.264 in.) |
| 5. INSTALL WINDSHIELD GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of a new windshield glass adhesive dam with Primer G.

| *A | Back Side | - | - |
| *1 | Primer G | *2 | Ceramic Notch |
| *3 | Label Area | - | - |
| Area | Dimension |
| a | 33.0 mm (1.30 in.) |
| b | 10.0 mm (0.394 in.) |
| c | 55.0 mm (2.17 in.) |
Install the windshield glass adhesive dam onto the windshield glass as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Ceramic Notch | *2 | Windshield Glass Adhesive Dam |
| Area | Dimension |
| a | 36.0 mm (1.42 in.) |
| 6. INSTALL WINDSHIELD GLASS SUB-ASSEMBLY |
![]() |
Position the windshield glass sub-assembly.
| *1 | Matchmark |
Using suction cups, place the windshield glass sub-assembly in the correct position.
Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.
Align the matchmarks on the windshield glass sub-assembly and vehicle body.
Remove the windshield glass sub-assembly.
Using a brush, coat the installation surface on the vehicle body with Primer M.

| *1 | Brush | *2 | Primer M |
| *3 | Adhesive | - | - |
| *a | CORRECT | *b | INCORRECT |
Using a brush or sponge, coat the application area of adhesive with Primer G.

| *A | Back Side | - | - |
| *1 | Primer G | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
| a | 9.6 mm (0.378 in.) or more |
| b | 16.5 mm (0.650 in.) or more |
| c | 18.5 mm (0.728 in.) or more |
| d | 11.0 mm (0.433 in.) or more |
Apply adhesive to the glass.
![]() |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| *1 | Nozzle |
| Area | Dimension |
| a | 8.0 mm (0.315 in.) or more |
| b | 12.0 mm (0.472 in.) or more |
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Adhesive | *2 | Ceramic Notch |
| *3 | Adhesive Center | - | - |
| Area | Dimension |
| a | 9.5 mm (0.374 in.) |
| b | 9.5 mm (0.374 in.) |
| c | 4.0 mm (0.157 in.) |
| d | 8.0 mm (0.315 in.) |
| e | 4.0 mm (0.157 in.) |
![]() |
Install the windshield glass sub-assembly.
| *1 | Matchmark |
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until the applied adhesive becomes hard.
| Temperature | Minimum Time prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 7. INSPECT FOR LEAK AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 8. INSTALL ROOF HEADLINING ASSEMBLY |
Return the front section of the roof headlining assembly to the original position.
| 9. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
![]() |
Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
| *1 | Notch |
| *2 | Alignment Mark |
| 10. INSTALL VISOR HOLDER |
![]() |
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
| 11. INSTALL VISOR ASSEMBLY LH |
Install the visor assembly LH with the 2 screws.
| 12. INSTALL VISOR BRACKET COVER (for LH Side) |
![]() |
Engage the 4 claws to install the visor bracket cover.
| 13. INSTALL VISOR ASSEMBLY RH |
| 14. INSTALL VISOR BRACKET COVER (for RH Side) |
| 15. INSTALL REAR ASSIST GRIP ASSEMBLY LH |
![]() |
Put an rear assist grip assembly LH together as shown in the illustration.
![]() |
Engage the 2 clips to install the rear assist grip assembly LH.
![]() |
Engage the 4 claws to install the 2 assist grip covers
| 16. INSTALL REAR ASSIST GRIP ASSEMBLY RH |
| 17. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
Put an assist grip sub-assembly together as shown in the illustration.
![]() |
Engage the 2 clips to install the assist grip sub-assembly.
![]() |
Engage the 4 claws to install the 2 assist grip covers
| 18. INSTALL SPOT LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 claws to install the spot light assembly.
| *a | Front |
| 19. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof) |
Connect the connector.
![]() |
Engage the 4 clips to install the roof console box assembly.
| 20. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof) |
Connect the connector.
![]() |
Engage the 4 clips to install the roof console box assembly.
| 21. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
![]() |
Install the front pillar garnish clip to front pillar garnish LH.
Engage the 2 guides as shown in the illustration.
![]() |
Engage the 2 clips to install the front pillar garnish LH.
| 22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 23. INSTALL FRONT PILLAR GARNISH RH |
| 24. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 25. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) |
Engage the 2 claws to install the rain sensor cover.
| 26. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow in the illustration to install it.
| *1 | Lock Lever |
Engage the 2 claws to install the inner mirror base cover.
| 27. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.
![]() |
Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration and engage the 2 claws to install the cover.
| 28. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow in the illustration to install it.
| *1 | Lock Lever |
Engage the 2 claws to install the inner mirror base cover.
| 29. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 8 guides as shown in the illustration.

Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

| 30. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the 3 guides and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.
| 31. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
| 32. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
When reusing the front wiper arm and blade assembly LH:
Clean the wiper arm serrations.
| *a | Wiper Arm Serration |
![]() |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
| *a | Wiper Pivot Serration |
![]() |
Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.
| Area | Measurement |
| A | 7.5mm (0.295 in.) |
| *1 | Ceramic Dot |
| 33. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
When reusing the front wiper arm and blade assembly RH:
Clean the wiper arm serrations.
| *a | Wiper Arm Serration |
![]() |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
| *a | Wiper Pivot Serration |
![]() |
Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.
| Area | Measurement |
| A | 7.5mm (0.295 in.) |
| *1 | Ceramic Dot |
Turn the ignition switch to ON.
Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.
Lift each wiper arm twice after the wipers stop and check the wiper set position.
Turn the ignition switch off.