Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A194498E40

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A74-20 (BATT) - E83-104 (E1)
GR - BR
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A74-3 (+BM) - E83-104 (E1)
LG - BR
Power source of throttle actuator
Always
11 to 14 V
A74-28 (IGSW) - E83-104 (E1)
V - BR
Ignition switch signal
Ignition switch ON
11 to 14 V
A74-2 (+B) - E83-104 (E1)
P - BR
Power source of ECM
Ignition switch ON
11 to 14 V
A74-1 (+B2) - E83-104 (E1)
LG - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E83-100 (OC1+) - E83-123 (OC1-)
W - B
Camshaft timing oil control valve assembly operation signal
Idling
Pulse generation
(See waveform 1)
A74-44 (MREL) - E83-104 (E1)
BE - BR
EFI MAIN relay operation signal
Ignition switch ON
11 to 14 V
E83-118 (VG) - E83-116 (E2G)
L - W
Mass air flow meter sub-assembly signal
Idling, shift lever in P, A/C switch off
0.5 to 3.0 V
E83-65 (THA) - E83-88 (ETHA)
P - Y
Intake air temperature sensor signal
Idling, intake air temperature 20°C (68°F)
0.5 to 3.4 V
E83-97 (THW) - E83-96 (ETHW)
B - P
Engine coolant temperature sensor signal
Idling, engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
E83-67 (VCTA) - E83-91 (ETA)
B - R
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E83-115 (VTA1) - E83-91 (ETA)
Y - R
Throttle position sensor signal (for engine control)
Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
3.2 to 4.8 V
E83-114 (VTA2) - E83-91 (ETA)
L - R
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch ON,
accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON,
accelerator pedal fully depressed
4.6 to 5.0 V
A74-55 (VPA) - A74-59 (EPA)
G - Y
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
A74-56 (VPA2) - A74-60 (EPA2)
R - BE
Accelerator pedal position sensor signal
Ignition switch ON,
accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 4.75 V
A74-57 (VCPA) - A74-59 (EPA)
P - Y
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
A74-58 (VCP2) - A74-60 (EPA2)
L - BE
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
E83-109 (HA1A) - E83-46 (E04)
G - W-B
Air fuel ratio sensor (sensor 1) heater operation signal
Idling
Pulse generation
(See waveform 2)
Ignition switch ON
11 to 14 V
E83-112 (A1A+) - E83-104 (E1)
L - BR
Air fuel ratio sensor (sensor 1) signal
Ignition switch ON
3.3 V*1
E83-113 (A1A-) - E83-104 (E1)
P - BR
Air fuel ratio sensor (sensor 1) signal
Ignition switch ON
2.9 V*1
E83-47 (HT1B) - E83-46 (E04)
LG - W-B
Heated oxygen sensor (sensor 2) heater operation signal
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
E83-64 (OX1B) - E83-87 (EX1B)
W - B
Heated oxygen sensor (sensor 2) signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 3)
E83-108 (#10) - E83-45 (E01)
B - W-B
No. 1 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
E83-107 (#20) - E83-45 (E01)
R - W-B
No. 2 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
E83-106 (#30) - E83-45 (E01)
Y - W-B
No. 3 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
E83-105 (#40) - E83-45 (E01)
L - W-B
No. 4 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
E83-110 (KNK1) - E83-111 (EKNK)
R - G
Knock control sensor signal
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
E83-122 (NE+) - E83-121 (NE-)
B - W
Crankshaft position sensor signal
Idling
Pulse generation
(See waveform 6)
E83-99 (G2+) - E83-98 (G2-)
Y - L
Camshaft position sensor signal
Idling
Pulse generation
(See waveform 6)
E83-85 (IGT1) - E83-104 (E1)
W - BR
No. 1 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 7)
E83-84 (IGT2) - E83-104 (E1)
G - BR
No. 2 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 7)
E83-83 (IGT3) - E83-104 (E1)
GR - BR
No. 3 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 7)
E83-82 (IGT4) - E83-104 (E1)
LG - BR
No. 4 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 7)
E83-81 (IGF1) - E83-104 (E1)
V - BR
Ignition coil assembly (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 7)
E83-49 (PRG) - E83-45 (E01)
W - W-B
Purge VSV operation signal
Ignition switch ON
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 8)
A74-8 (SPD) - E83-104 (E1)
L - BR
Vehicle speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 9)
A74-48 (STA) - E83-104 (E1)
LG - BR
ST relay operation signal
Cranking
5.5 V or higher
E83-52 (NSW) - E83-104 (E1)
LG - BR
Park/Neutral position switch assembly signal
Ignition switch ON, shift lever not in P or N
11 to 14 V
Ignition switch ON, shift lever in P or N
Below 2.0 V
A74-36 (STP) - E83-104 (E1)
BE - BR
Stop light switch assembly signal
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A74-35 (ST1-) - E83-104 (E1)
GR - BR
Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
E83-42 (M+) - E83-43 (ME01)
W - W-B
Throttle actuator operation signal (positive terminal)
Idling with warm engine
Pulse generation
(See waveform 10)
E83-41 (M-) - E83-43 (ME01)
B - W-B
Throttle actuator operation signal (negative terminal)
Idling with warm engine
Pulse generation
(See waveform 11)
A74-7 (FC) - E83-45 (E01)
V - W-B
Fuel pump control
Ignition switch ON
11 to 14 V
A74-24 (W) - E83-104 (E1)
R - BR
Malfunction Indicator Lamp (MIL) operation signal
Ignition switch ON
(MIL goes on)
Below 3.0 V
Idling
11 to 14 V
A74-27 (TC) - E83-104 (E1)
P - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
A74-15 (TACH) - E83-104 (E1)
B - BR
Engine speed signal from combination meter assembly
Idling
Pulse generation
(See waveform 12)
E83-50 (ALT) - E83-104 (E1)
L - BR
Generator assembly
Ignition switch ON
11 to 14 V
A74-41 (CANH) - E83-104 (E1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 13)
A74-49 (CANL) - E83-104 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 14)
A74-21 (FANL) - E83-45 (E01)
R - W-B
Cooling fan motor operation signal (low)
Ignition switch ON
11 to 14 V
Idling with A/C on, or high engine coolant temperature
Below 1.5 V
A74-22 (FANH) - E83-45 (E01)
W - W-B
Cooling fan motor operation signal (high)
Ignition switch ON
11 to 14 V
Idling with high engine coolant temperature
Below 1.5 V
A74-32 (EC) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-104 (E1) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-45 (E01) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-44 (E02) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-86 (E03) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-46 (E04) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-43 (ME01) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E83-63 (GE01) - Body ground
G - -
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω
  1. *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E38
Camshaft Timing Oil Control Valve Assembly Operation Signal 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 2
A205412E01
Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal 
ECM Terminal Name
Between HA1A and E04
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E15
Heated Oxygen Sensor (Sensor 2) Operation Signal 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, the item O2S B1S2 shows the values input to the ECM from the heated oxygen sensor.


WAVEFORM 4
A093279E24
No. 1 (to No. 4) Fuel Injector Assembly Signal 
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E82
Knock Control Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.


WAVEFORM 6
A063955E53
Crankshaft Position Sensor Signal and Camshaft Position Sensor Signal 
ECM Terminal Name
CH1: Between G2+ and G2-
CH2: Between NE+ and NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A289263E01
Ignition Coil Assembly Signal (IGT and IGF Signal) 
ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A218020E01
Purge VSV Operation Signal 
ECM Terminal Name
Between PRG and E01
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 9
A005135E29
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 10
A208000E03
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A245848E01
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A093225E33
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 13
A086154E48
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 14
A086155E44
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.